• Clean Technology
• /
• v.22 no.1
• /
• pp.9-15
• /
• 2016

xAl-yZr mixed oxide catalysts with different molar ratios of Al/(Al+Zr) were prepared by a co-precipitation method and its catalytic performance was compared in the iso-propanol dehydration as a model reaction. The catalysts were characterized by X-ray diffraction (XRD), differential thermal analysis (DTA), N₂ adsorprion-desorption, NH₃ temperature programmed desorption (NH₃-TPD), and iso-propanol TPD analyses. The addition of Al into ZrO₂ promoted the formation of relatively small particles with large surface areas and retarded the transformation of teragonal phase to monoclnic phase. NH₃-TPD results revealed that the relative acidity of the catalysts increased along with the increase of Al molar ratio. The catalytic activity for the dehydration of iso-propanol to propylene was also increased with the same tendency. The catalytic activity could be correlated with high surface area, acidity and easy desorption of iso-propanol.

• Clean Technology
• /
• v.20 no.3
• /
• pp.330-336
• /
• 2014

Mg-Al mixed oxides with molar ratio of Mg/Al = 1-3 were prepared by co-precipitation and characterized by using X-ray diffraction, scanning electron microscopy, BET surface area and pore volume measured by $N_2$ sorption analysis, and temperature programmed desorption of iso-propanol. As Al content in Mg-Al mixed oxide increased, the acidity and BET surface area proportionally increased. This increase of acidity directly influenced the catalytic activity of iso-propanol conversion and selectivity to propylene.

• Applied Chemistry for Engineering
• /
• v.28 no.6
• /
• pp.649-654
• /
• 2017

An activated carbon was prepared from waste citrus peel produced in large amounts in Jeju Island, Korea, using KOH activation and its characteristics was examined. Under the condition of the KOH ratio between 100 and 300%, activation temperature from 400 to $900^{\circ}C$ and activation time from 0.5 to 1.5 h, the iodine adsorptivity of the activated carbon prepared increased but the yield decreased with respect to the increase of each conditions. The iodine adsorptivity and yield of the activated carbon prepared at the activation time of more than 1.5 h were similar to those of using 1.5 h. In addition, as the KOH ratio increased, the specific surface area and pore volume of the activated carbon increased, but the pore diameter decreased. The activated carbon has an average pore diameter of $20{\sim}25{\AA}$. Also, the activated carbon prepared at 300% KOH and $900^{\circ}C$ for 1.5 h has the highest specific surface area of $1,527m^2/g$ and iodine adsorptivity of 1,246 mg/g.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.41-41
• /
• 2010

에어컨용 냉매 압축기, 냉장고용 냉매압축기 및 자동차 샷시 부품들은 주로 겹치기 필릿용접을 GMAW 으로 실시하고 있다. 그러나 용접 시 스패터 발생으로 인한 추가공수가 요구되며 작업환경 또한 열악한 실정이다. 따라서 저가의 고생산이면서 용접비드의 외관이 미려하고 스패터, 소음 그리고 Fume 이 발생되지 않는 청정한 TIG 용접이 있지만, 용접속도가 수십 cpm 이하로 제한되어 생산성이 낮다는 기술적 모순을 가지고 있다. TIG 용접에서 생산성을 증가시키기 위해 모재와 와이어를 고속 용융 시키려면 전류를 높여 입열량을 증가시켜야 하지만, 증가된 전류로 인하여 상승된 아크력이 험핑비드와 언더컷이 발생되는 물리적 모순을 가진다. 또한 필러와이어를 사용한 기존의 TIG 용접에서 필러 와이어는 주로 원형 단면 와이어를 사용하게 되는데 와이어의 직경이 증가함에 따라 비표면적은 감소하여 용융효율이 낮아지므로 $\Phi$1.2 이하의 필러와이어를 송급하여 용접하였다. 그러나 요구되는 용착량이 큰 경우 필러 와이어를 고속으로 송급하게 되는데 이 경우 필러 와이어 용융이 곤란하거나 송급상의 문제가 자주 생겨 용접속도를 고속으로 하기 곤란하였다. 따라서 필러와이어를 사용한 TIG 용접에서 용착금속의 용융효율을 높게 함으로서 전류를 크게 증가시키지 않으면서도 용접속도를 높일 수 있는 용접 공정개발이 필요한 실정이다. 본 연구에서는 비표면적을 증가시켜 용착금속의 높은 용융효율을 얻을 수 있도록 개발된 와이어와 기존의 $\Phi$3.2 일반와이어 및 를 이용하여 BOP TIG 용접에 비교 실험하였으며, 개발된 와이어와 기존의 $\Phi$1.2 필러와이어를 이용하여 필릿용접부에 적용 실험하여 비교하였다. 그 결과 개발된 와이어의 경우 적절한 비드를 형성하였으나 3.2 일반와이어의 경우 과도한 볼록비드와 불용착부의 문제가 발생하였고, 필릿용접 비교실험에서는 각각 200cpm과 50cpm에서 적절한 비드가 형성되어 더 높은 용착금속 용융효율을 얻을 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.3
• /
• pp.205-212
• /
• 2010

This study was carried out to investigate the characterization of aerogel made by holocellulose, the thermal properties of the aerogel, and its shapes and porous structures. The aerogel was made by holocellulose through the gelation in alkali hydroxide-urea solution and freeze drying processes. Holocellulose aerogel had porous structure such as net or sponge. The density of holocellulose aerogel was 0.04 g/$cm^3$, and the specific surface area 145.3 $m^2$/g. Although thermal degradation occurred in the range of $210{\sim}350^{\circ}C$, significant thermal degradation occurred at low temperature with low heating rate, Micropore volume was sharply increased with low heating rate. Holocellulose aerogel char obtained by carbonization with $900^{\circ}C$ and $0.5^{\circ}C$/min. heating rate had the highest surface area, 656.7 $m^2$/g. The deformed and irregular structures of holocellulose aerogel chars due to the thermal degradation were observed in SEM.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.1
• /
• pp.115-121
• /
• 1997

This study deals with the suppressing characteristics of alkali-silica reaction by ground granulated blast-furnace slag(GGBS) in NaCl solution. NaCl contents used in the experiment ranges over 0%, 2.8% and 20%. Reactive aggregate used is Japanese andesite. Also, three GGBSs of about 4.000. 6, 000 and $8, 000cm^2/g$ were used in the experiment. The replacement proportions of portland cement by GGBSs were 40%. 60%, 70% and 80%. respectively. The specimens with GGBS were severely contracted according to the increasing replacement ratio in NaCl solution. The contraction rate increases according to the increasing in NaCl content. Also. it does with increasing the blaine fineness of GGRS. It is concluded that the suppression of alkali-silica reaction by GGBS in NaCl solution is complished by contraction of GGBS due to chloride ion induced chemical shrinkage.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.3
• /
• pp.126-132
• /
• 2002

The nanocrystalline zirconia powder with anisotropic shapes was synthesized by hydrothermal treatment of the tetragonal zirconia prepared by aging the zirconium hydroxide precipitate, which was obtained from the reaction between $ZrOCl_2{\cdot}8H_2O$ and KOH solutions under the fixed pH of 13.5, at $100^{\circ}C$ for 24 h. With increasing the hydrothermal reaction temperature and time, the fraction of tetragonal phase with spherical zirconia decreased, whereas, relatively the fraction of monoclinic phase with spindle-like and rod shape zirconia increased. As increased concentration of the NaOH solution it promoted the particle size to become larger and the crystalline phase to transform tetragonal to monoclinic. However, the specific surface area at the early stage of the reaction increased and subsequently decreased because of grain growth in powder with longer reaction time.

• Polymer(Korea)
• /
• v.26 no.2
• /
• pp.160-167
• /
• 2002

We synthesized HPP-g-GMA copolymer using pre-irradiation method by E-beam and aminated HPP-g-GMA using amination reaction. Degree of grafting increased with increasing GMA monomer concentration and showed the maximum value of 130% at 1.46 M of GMA. The degree of amination increased with increasing the degree of grafting. When the degree of grafting was 100%, degree of amination showed the maximum value of 37.4%. The ion exchange capacity of aminated HPP-g-GMA was about 3.78 meq/g, and it showed remarkable adsorption ability of hollow fiber ion exchanger. Through the BET analysis, the surface area of aminated HPP-g-GMA was 54.83 $\m^2/g$ and the mean pore size was $26\AA$. These showed the decrease of surface area and the slight increase of the mean pore size. SEM results show that the thickness of fiber increased after the step of reaction and there pore blocking phenomena was not observed. The aminated HPP-g-GMA was synthesized successfully and found to be suitable for the adsorption and separation of anion.

• Korean Journal of Materials Research
• /
• v.6 no.9
• /
• pp.943-949
• /
• 1996

카올린에서 추출된 황산알루미늄 용액으로부터 촉매담체용 r-AI2O3분말 합성에 대하여 연구하였다. 황산알루미늄 용액을 교반중의 에탄올(ethanol)에 적하하여 단일상(single phase)의 AI2(So4)3 18H2O석출물을 제조하고 이 석출물의 하소로부터 r-AI2O3분말을 합성하였다. 이 분말을 100$0^{\circ}C$에서 2시간 하소하였을 때 열적안정성을 보였으나, 120$0^{\circ}C$-2시간 하소에서 $\alpha$-AI2O3 로 전이하였다. r-AI2O3의 열적안정성에 미치는 BaO 첨가의 영향을 조사 연구하였다. 첨가량은 r-AI2O3에 대해서 1.0-6.0wt%로 하였다. BaO를 4.0wt%첨가한 시료는 AI2O3-BaO.6AI2O3(hexa-aluminate)혼합상생성으로 인하여 120$0^{\circ}C$에서 r-AI2O3의 전이를 방지하는데 효과적이었다. BaO를 4.0wt%첨가한 시료와 BaO를 첨가하지 않은 시료에 대하여 r-AI2O3$\longrightarrow$ $\alpha$-AI2O3전이에 따른 비표면적을 조사하여 보았다. 120$0^{\circ}C$-2시간에서 BaO 4.0wt% 첨가한 시료와 BaO를 첨가하지 않은 시료의 비표면적은 각각 95$m^2$/g과 50$m^2$/g을 유지하였다.

• Journal of Sensor Science and Technology
• /
• v.3 no.3
• /
• pp.9-15
• /
• 1994

Catalytic combustible gas sensors were fabricated by using ${\gamma}-Al_{2}O_{3}$ with large surface area and noble metal catalysts. The optimum conditions for ${\gamma}-Al_{2}O_{3}$ fabrication were investigated by DT/TGA and XRD analyses and it was found that fabricated ${\gamma}-Al_{2}O_{3}$ had superior value as surface area of $215.5m^{2}/g$. Gas sensors were manufactured and tested to inflammable gases by using Pt coil as a heater and temperature sensing part, fine ${\gamma}-Al_{2}O_{3}$ powder as a bead material and Pt, Pd noble metal powder as a catalyst. From the results, fabricated sensor showed good sensitivity to LPG and LNG of 20mV/l000ppm, 6.5mV/l000ppm respectively.