• Resources Recycling
• /
• v.14 no.3
• /
• pp.63-67
• /
• 2005

As there are recent tendencies to raise horizontal frequencies so as to improve screen definition for high-quality TV and high definition display, ferrite core for deflective yokes requires materials with low coreloss in the areas of high frequencies. The researcher added CuO to low-loss Mg-Zn ferrite. After choosing MgO, ZnO, Fe$_2O_3$ and CuO, the researcher changed a ratio of composition, substituting MgO for CuO. These samples were sintered for three hours up to 980$^{\circ}C$~1350$^{\circ}C$. Measure magnetic permeability, electric loss, core loss and a rate of contraction.

• Resources Recycling
• /
• v.12 no.6
• /
• pp.26-31
• /
• 2003

The power loss characteristics of Mn-Zn ferrite were observed with the sintering temperature. In case of $1150 ^{\circ}C$ sintering, the core loss increased with measuring temperature, and does not have minimum value at the point where the magnetocrystalline anisotropy be 'zero'. This reason mainly due to the change of core loss mechanism with grain size which affects residual loss. The grain size and sintered density slightly increased with equilibrium oxygen partial pressure at$ 1150 ^{\circ}C$ sintering. The resistivity and initial permeability showed no significance with atmosphere, these results due to complex effect of $Fe^{2+}$ concentration and microstructure change. The core loss at $100^{\circ}C$ decreased as the equilibrium oxygen partial pressure increased.e increased.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.12
• /
• pp.993-998
• /
• 2017

In this paper, a high-accuracy current sensing technique for three-phase current paths in an electrical switchboard is proposed. Conventional open-style current sensors using magnetic sensors show inaccurate sensing performance with more than 10% error due to undesired magnetic field interference from neighboring paths. To increase accuracy, large and expensive current transformers with large permeabilities have been used, which increased the cost and size. The proposed technique can improve the measured magnetic field by the calculation of magnetic interference effect from neighboring current paths. The relationship between neighboring magnetic fields and the desired magnetic field is theoretically analyzed in a general case. The proposed technique is verified using magnetic field simulations in a three-phase busbar environment.

• Korean Journal of Construction Engineering and Management
• /
• v.7 no.1 s.29
• /
• pp.168-175
• /
• 2006

Since the partly changed 'Private Investment Act for Social Infrastructure Projects' set forth in January 2005, the number of BTL(Build-Transfer-Lease) projects offered to the market has rapidly increased. The scope of BTL projects offered covers not only legally defined facilities but several facilities for the private schools. A BTL project, by definition, is a way of project management that includes the entire process of development such as planning, design, construction and operation over the period of 20-30 years. As a result, various types of risk may happen at each stage of the project and it is extremely important to efficiently control the sensitive factors that affect the risk profiles of the project. The examples of the sensitive factors are construction cost, interest rate, discount rate, lease amount, rental fee, O&M cost and so on. This study examines the characteristics of these sensitivity factors, analyzes their impact on the project feasibility and suggests the alternatives to manage them efficiently.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.1
• /
• pp.25-30
• /
• 2017

In this paper, dual band patch antenna was designed using a CSRR structure with negative values permeability which inserted into the ground plane. We propose an antenna that can be used in dual band f1(1.53GHz) and f2(1.63GHz) for satellite communications by using the CSRR placed on the backside of feeding line, which is a negative shape of SRR. The proposed antenna can be arrayed using microstrip line and can be made smaller than conventional patch antenna. The fabricated antenna has the input reflection coefficient of -12.5dB and -14.5dB at f1 and f2, and the gain of 2dB and -0.8dB, respectively. and it was confirmed that the performance was sufficient in the dual-band.

• Korean Journal of Crystallography
• /
• v.12 no.3
• /
• pp.182-187
• /
• 2001

The purpose of this study is to investigate the degradation of soft magnetic properties of Fe-Hf-N thin films after annealing in vacuum. They were annealed at 450℃∼650℃. The microstructure and crystal phase of the selected area of the thin films were analyzed by TEM and SAD. After annealing at 450℃-600℃, the coercivity of the films increased by 0.2 Oe and the effective permeability decreased by 1500 as compared with them before annealing due to the growth of α-Fe crystallites. The saturation magnetic flux density of the films increased by 0.5 KG after annealing under 600℃. However, the soft magnetic properties of the film annealed at 650℃ degraded abruptly, which was attributed to the destruction of nano-crystalline microstructure of the film due to the rapid growth of α-Fe crystallites with the segregation of N sited in the α-Fe lattice into HfN.

• Journal of the Korean Magnetics Society
• /
• v.12 no.2
• /
• pp.51-56
• /
• 2002

Permalloy thin films fabricated by rf magnetron sputtering showed the excellent magnetic properties, i.e., an effective permeability of over 2000 at 1$\mu\textrm{m}$ thick up to 10 MHz, a saturation magnetization of 10∼12 kG, a coercive force of 0.2∼1 Oe, resistivity (p) is 20 ${\mu}$$\Omega$cm. In order to control the magnetic anisotropy direction of the films in a wafer scale, two parallel Nd-Fe-B permenant mangnets were used to provide the magnetic field during the sputtering process. As a result, the anisotropy direction was successfully controlled when the two magnets were seperated with a distance of 70 mm. 3D simmulation of the magnteic fields around the wafer during sputtering were in accord with the above result.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.8
• /
• pp.933-939
• /
• 2008

In this paper, a new composite electromagnetic bandgap(EBG) structure using magnetic materials is proposed for simultaneous switching noise(SSN) suppression in the high-speed digital circuits. The proposed EBG structure has periodic unit cells of square-patches connected by spiral-shaped bridges. The magnetic materials are located on the unit cells of spiral-shaped EBG. The real part of the permeability shifts bandgap to the lower frequency region due to the increased effective inductance. The imaginary part of the permeability has magnetic loss that decreases parasitic LC resonance peaks from between the unit cells. As a result, the proposed structure has the lower cut-off frequency compared with conventional EBG structure and -30 dB SSN suppression bandwidth from 175 MHz to 7.7 GHz. The proposed structure is expected to improve the power integrity and reduce the size of the EBG power plane.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10B
• /
• pp.676-688
• /
• 2005

We introduced mathematical economic analysis model for understanding the fairness of charge from VoIP providers for interconnection of access network. In order to set up this model we made four assumptions predictable in the real world. Also we proposed two accounting method that is flat-rate-pricing and usage-based-pricing and tried to propose which method is more desirable to charge for interconnection on the basis of social welfare and activation of market competitiveness. The outcome of this study includes the reasonable accounting method for interconnection between telephone network and IP Phone network which is most effective to ensure the social welfare and market competitiveness

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.231-234
• /
• 2007

The magnetic sensor using electromagnetic principle. which transfers magnatic into electric. is the electric component.It has been widely applied to the industry, university and the reseach. However there are some problems. Not only the korean domestic sensor manufacture skills are still lower then the advanced manufacture's but also production of sensor is not well organized yet. Due to cahnging excitation cvurrent, excitation freq and the rate magnetic permeability core, there sometimes would be distorted phenomena or loaded phenomena which result in limited measurment range. Therefore, the signal conversion device should support to receive undistorted and nice output. This paper focuses on both the design of signal transform circuit using inductive proximity sensor and the signal transfer equipment (Z device) which detects thickness of painted material.