• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.8
• /
• pp.91-100
• /
• 2004

A Green's function approach is adopted for analyzing the thermoelastic deformations and stresses of a plate made of functionally graded materials(FGMs). The solution to the 3-dimensional unsteady temperature is obtained by using the laminate theory. The fundamental equations for thermoelastic problems are derived in terms of out-plane deformation and in-plane force, separately. The thermoelastic deformation and the stress distributions due to the bending and in-plane forces are analyzed by using a Green's function based on the Galerkin method. The eigenfunctions of the Galerkin Green's function for the thermoelastic deformation and the stress distributions are approximated in terms of a series of admissible functions that satisfy the homogeneous boundary conditions of the rectangular plate. Numerical analysis for a simply supported plate is carried out and effects of material properties on unsteady thermoclastic behaviors are discussed.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.4 no.2
• /
• pp.117-131
• /
• 2006

A coupled T-H-M(Thermo-Hydro-Mechanical) analysis was carried out for KENTEX (KAERI Engineering-scale T-H-M Experiment for Engineered Barrier System), which is a facility for validating the coupled T-H-M behavior in the engineered barrier system of the Korean reference HLW(high-level waste) disposal system. The changes of temperature, water saturation, and stress were estimated based on the coupled T-H-M analysis, and the influence of the types of mechanical constitutive material laws was investigated by using elastic model, poroelastic model, and poroelastic-plastic model. The analysis was done using ABAQUS, which is a commercial finite element code for general purposes. From the analysis, it was observed that the temperature in the bentonite increased sharply for a couple of days after heating the heater and then slowly increased to a constant value. The temperatures at all locations were nearly at a steady state after about 37.5 days. In the steady state, the temperature was maintained at $90^{\circ}C$ at the interface between the heater and the bentonite and at about $70^{\circ}C$ at the interface between the bentonite and the confining cylinder. The variation of the water saturation with time in bentonite was almost same independent of the material laws used in the coupled T-H-M processes. By comparing the saturation change of T-H-M and that of H-M(Hydro-Mechanical) processes using elastic and poroelastic material mod31 respectively, it was found that the degree of saturation near the heater from T-H-M calculation was higher than that from the coupled H-M calculation mainly because of the thermal flux, which seemed to speed up the saturation. The stresses in three cases with different material laws were increased with time. By comparing the stress change in H-M calculation using poroelasetic and poroelasetic-plastic model, it was possible to conclude that the influence of saturation on the stress change is higher than the influence of temperature. It is, therefore, recommended to use a material law, which can model the elastic-plastic behavior of buffer, since the coupled T-H-M processes in buffer is affected by the variation of void ratio, thermal expansion, as well as swelling pressure.

• Journal of the Korean Ceramic Society
• /
• v.38 no.2
• /
• pp.193-198
• /
• 2001

유한요소법을 이용하여 STS VOD 래들에서 내장 내화물의 재질 및 back filler의 시공 위치에 따른 열응력을 수행하였다. 불소성 내화물의 경우 높은 열전도율에 의해 가동면과 배면(back face)간의 온도구배가 소성품에 비해 감소하였으며 탄성계수도 낮아 발생되는 열응력이 2~4배 낮았다. Back filler는 dolomite 내화물의 열간 팽창을 흡수하기 위해 시공하는 것으로, 상대적으로 낮은 열전도율을 가지고 있기 때문에 back filler의 내부와 외부에 급격한 온도구배가 발생된다. 결과적으로 래들의 내부는 고온을 유지하여 내화물이 팽창이 되고, 외부는 온도가 낮아지므로 수축되어 열응력이 증가하였다.

• Explosives and Blasting
• /
• v.29 no.1
• /
• pp.34-40
• /
• 2011

In this study, effects that thermal stress and water pressure have on the deformation behaviour of granite specimens recovered in Gagok Mine are estimated. To analyze effects of the thermal stress and water pressure on the deformation behaviour, granite specimens were preheated with cycles of predetermined temperatures ranging $200^{\circ}C$ to $700^{\circ}C$ and 500, 600, $700^{\circ}C$ specimens were pressurized to 7.5 MPa. The deformation behaviour of the specimens had been studied by performing uniaxial compressive tests. Axial and lateral strains of specimens were found to increase with increasing temperature, and above $600^{\circ}C$, the increase of strains were more pronounced. The reduction trends of uniaxial compressive strength and Young's modulus with temperature appeared to follow an exponential decay function. Specimens under water pressure showed the more inelastic deformation characteristics, which means that water pressure has an effect on the widening and extending of micro-cracks existed in preheated specimens.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.4
• /
• pp.1009-1018
• /
• 1994

An attempt is made to develop a kind of hybrid numerical method for computations of the thermal stresses during a solidification process. In this algorithm, the phase-change heat transfer analysis is perrformed by a finite volume method(FVM) and the thermal stress analysis in a solidifying body by a finite element method(FEM). The temperatures at the grid points calculated in the heat transfer analysis are transferred to those of gauss points in elements by a bi-cubic surface patch technique for the thermal stress analysis. A hyperbolic-sine constitutive law is used to prescribe the inelastic strain rate of material. Results for the unidirectional solidification process of a pure aluminum are compared with those of others and shows good agreement.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.7
• /
• pp.1042-1049
• /
• 1997

LMFBR(Liquid Metal Fast Breeder Reactor) vessel is operated under the high temperatures of 500-550.deg. C. Thus, transient thermal loads were severe enough to cause inelastic deformation due to creep-fatigue and plasticity. For reduction of such inelastic deformations, Y-piece structure in the form of a thermal sleeve is used in LMFBR vessel under repeated start-up, service and shut-down conditions. Therefore, a systematic method for inelastic analysis is needed for design of the Y-piece structure subjected to such loading conditions. In the present investigation, finite element analysis of heat transfer and inelastic thermal stress were carried out for the Y-piece structure in LMFBR vessel under service conditions. For such analysis, ABAQUS program was employed based on the elasto-plastic and Chaboche viscoplastic constitutive equations. Based on numerical data obtained from the analysis, creep-fatigue damage estimation according to ASME Code Case N-47 was made and compared to each other. Finally, it was found out that the numerical predictio of damage level due to creep based on Chaboche unified viscoplastic constitutive equation was relatively better compared to elasto-plastic constitutive formulation.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.94-94
• /
• 2011

스포츠웨어 바람막이용도에 사용되는 대부분의 소재는 폴리아미드계 소재이며, 국내에서는 대부분 나일론6 소재를 사용하고 있다. 최근 소비자들의 요구는 점점 경량화되고 있고 야외활동 증가와 더불어 착용감이 우수한 소재를 요구하고 있다. 이러한 시즘에 국내에서 많이 사용되는 나일론6 소재를 이용하여 직물단계에서 경량감과 스트레치성이 발현될수 있는 나일론6 세섬 권축사 개발에 대한 연구를 진행하고자 함이다. 본 연구에서는 직물단계에서 경량감과 스트레치성이 발현될수 있는 나일론6 세섬 권축사 개발을 위해 공중합 나일론6 폴리머와 일반 나일론6 폴리머를 복합방사설비를 이용하여 SIDE BY SIDE POY 26d/6f 원사를 제조하였다. 원사물성은 섬도 25.8d, 절단신도 71%, 절단강도 4.3g/d의 물성을 가졌으며, Nip Belt 가연설비로 연신비, 가연 1st 히터온도, 벨트각도 조건에 따라서 제조된 나일론6 가연사 DTY 20d/6f의 물성을 평가하였고, 비교사로서 T사에서 생산되고 있는 나일론6 가연사 DTY 20d/6f와 비교평가하였다. 비수탄성율은 가연 연신비가 높고, 1st 히터온도가 높은 조건에서 높게 나타남을 알 수 있었으며, 염색 가공 공정에서의 전처리단계에서 $100^{\circ}C$정도의 열을 받았을 때의 수축에 따른 권축효과 발현에 따른 신축성 변화에 대한 상대평가를 사단계에서 유추할 수 있다. 권축효과가 높게 나타난다 하더라도, 사의 수축힘이 적으면 권축효과 발현특성에 큰 차이가 없으므로 열응력을 측정을 한 결과, 가연 연신비가 높고 가연 1st 히터온도가 높은 조건에서 열응력이 높게 나타남을 알 수 있었으며, 비교사에 비해 약간 높은 열응력 값을 보였다. 절단강도는 가연조건에 따라서 큰 변화가 없었고, 절단신도는 연신비가 증가함에 따라 점차 감소하였으며 비교사와도 큰 차이를 보이지 않았음. 따라서, POY 26d/6f 원사에 적합하고, 권축효과가 우수한 가연조건을 도출하였고, 가연현장 작업시 문제가 없는 가연 최적조건을 도출하였다. 향후, 가연조건에 따른 제조된 가연사를 이용하여 제직 및 염색가공 공정을 거친후, 직물신축성 평가를 실시할 계획이다.

• Journal of the Korean Society of Safety
• /
• v.19 no.4 s.68
• /
• pp.155-160
• /
• 2004

A simply supported rectangular thin plate with temperature distribution varying over the thickness is analyzed. Since the thermal deflections are large compared to the plate thickness during bending and membrane stresses are developed md as such a nonlinear stress analysis is necessary. For the geometrically nonlinear, large deflection behavior of the plate, the classical von Karman equations are used. These equations are solved numerically by using the finite difference method. An iterative technique is employed to solve these quasi-linear algebraic equations. The results obtained from the suggested method are presented and discussed.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05b
• /
• pp.659-665
• /
• 1995

액체금속로는 기존의 가압경수로와는 달리 55$0^{\circ}C$ 정도의 고온에서 운전이 되므로 고온 열응력이 중요한 문제로 대두되며 따라서 고은에서의 크립(Creep) 변형, 반복되는 기동과 정지 등으로 인한 되풀이 소성변형, 라체팅(Ratchetting), 크립과 소성의 상호작용 및 크립과 피로의 상호작용 등의 평가에 대한 기술 확립과 고온구조물에 대한 우리의 독자적인 설계방법을 개발하는 것이 필요하다 본 연구에서는 범용 유한요소해석코드인 ABAQUS의 축대칭 요소를 이용해서 액체 금속로 원자로용기와 이에 부착된 열소매(Thermal sleeve)를 Y-형태의 구조물로 모델링하여 반복되는 열천이하중에 대한 비탄성 구조해석을 수행하고 크립효과에 대한 영향을 분석하였다. 해석결과 액체금속로와 같은 고온구조물에 대하여 반복 열천이 하중과 고온 지속시간이 유발하는 크립효과가 크게 나타남을 알 수 있었다.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.11-15
• /
• 1990

고무재료는 강재에 비해 큰 탄성변형을 할 수 있고 충격 흡수능력이 뛰어나므로 자동차에서도 진동문제 및 승차감을 향상시키기 위하여 엔진 마운트, suspension bushing등을 비롯한 여러 곳에 사용되고 있다. 여기에 이용되는 고무재의 요구조건은 1) 피로수명이 충분히 길것, 2) 열 및 산화에 강할 것, 3) 소음이 없을 것 등이다. 본 고에서는 1)번의 요구조건을 기준으로 고무재의 기본적인 역학적 특성 및 해석방법을 소개하고자 한다.