• Journal of the Korean Institute of Intelligent Systems
• /
• v.8 no.6
• /
• pp.122-128
• /
• 1998

This paper presents compression of image sequences based on the classification of interframe difference image blocks. classification process consists of image activity classification and energy distribution classification. In the activity classification, interframe difference image blocks are classified into activity blocks and non-activity blocks using the edge detection. In the distribution classification, activity blocks are further classified into vertical blocks, horizontal blocks, and small activity blocks using the AC energy distribution features. The RBFN, trained with numerical classification results, successfully classifies difference image blocks according to image details. Image sequence compressing based on the classification of interframe difference image blocks using the RBFN shows better compression results and less training time than the classical sorting method and the MLP network.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.11
• /
• pp.1681-1690
• /
• 2013

In this paper, a design of speed and position controller based on the EKF(Extended Kalman Filter) for sensorless control in IPMSM(Interior Permanent Magnet Synchronous Motor) is proposed. The proposed method subdivides the state estimation interval for improving the accuracy of state estimation. and each subdivided interval estimated first order term using Taylor series. The proposed state estimator comparison with the second-order extended Kalman filter reduced calculation amount of a priori estimation. And the simulation results were proved that The accuracy of priori estimation is increased.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.5
• /
• pp.72-79
• /
• 2003

Spray characteristics were investigated by impinging F-O-O-F type injector with varying the impingement angle through 15, 20 and 30 degree and the mixture ratio(O/F ratio) from 1.5 to 3.0. Experimental results show that the correlation between dispersion and impingement angle is not influenced of the mixture ratio variation, but which has influence on number density, and there is a linear correlation between dispersion and impingement angle. Velocity distribution, standard deviation and SMD of droplets are decreased as the impingement angle increases. Also, it was confirmed that the distribution of droplet size are in accordance with Rosin-Rammler and Upper-limit distribution.

• Journal of the Korean Institute of Gas
• /
• v.19 no.5
• /
• pp.41-46
• /
• 2015

It is known that in aluminum 6061-T6, which is composed of $Mg_2Si$ and ${\beta}-Al_5FeSi$, void nucleation grows around ${\beta}-Al_5FeSi$ of Al606-T6. In this work, growth of voids was checked by scanning a 6061-T6 specimen with SEM observation. The effects of dislocation damping, coherency strain and voids on ultrasonic attenuation and nonlinearity parameters were experimentally measured. It was observed that a nonlinearity parameter increases until 75 percent of fatigue life and decreases after that. From the results, the authors inferred that dislocation damping and coherency damping increase nonlinearity parameters and void nucleation decreases them as ultrasonic scattering increases with void. The application of nonlinearity parameters in estimating degradation of materials with complex microstructures through fatigue process, therefore, should be carefully considered.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.5
• /
• pp.473-480
• /
• 2011

Recently, the resizing algorithms based on the displacement participation factors have been developed for sizing members to satisfy stiffness criteria. It is proved that this resizing algorithms made for utilizing worker's stiffness design are practical and rational due to the simplicity and convenience of the method. The resizing algorithm can be practically and effectively applied to drift design of buildings. However, the researches on the change of inelastic behavior by the resizing algorithm has been insufficient. To identify the effect on the inelastic behavior of buildings by the resizing method, this study used the reinforced concrete shear wall-frame example. Through the application of the resizing method, the weights of shear wall in the lower class and the weights of columns and beams in the upper class increased respectively. And the initial stiffness of the building increased and the ductility of the buildings had similar with that of the initial structure.

• Applied Chemistry for Engineering
• /
• v.19 no.5
• /
• pp.539-546
• /
• 2008

A study on the selection of an optimal entrainer as the third component among water, aniline, 1,3-diethylbenzene, furfural, and MEK, for the extractive distillation of an azeotropic acetone/methanol system was performed using both the entrainer effect vapor-liquid equilibrium (VLE) and the relative volatility. In the case of water as the entrainer, a VLE curve without azeotropic point in the range of water composition from 0.3 up to 0.7 mole fraction could be obtained by both the experiment and the calculation using modified-UNIFAC model. For aniline and 1,3-diethylbenzene, however, VLE curve without azeotropic point could be obtained only at compositions above 0.7 mole fraction, which exhibited that they could be hardly utilized as the entrainer. Moreover, both furfural and MEK were verified to be improper entrainer since they formed an azeotropic phase. Relative volatility of water showed greater than 1.0 and increased with compositions, while those of the others decreased non-linearly, exhibiting that only water could be utilized as the proper entrainer for the extractive distillation of azeotropic acetone/methanol system.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.1
• /
• pp.75-80
• /
• 2012

$InSb$ films were fabricated by DC magnetron sputtering and the effects of deposition temperature, heat treatment, passivation from evaporation and multi-layered structure were investigated. Electron mobility and electron concentration were linearly increased with deposition temperature for as-deposited specimens. It was found that the mobilities depend on the grain size rather than the stoichiometry for the samples with very low mobilities. The mobilities largely increased for the specimens with evaporation passivation compared with those without passivation layer. The mobility also increased with the amount of indium deposition in the multi-layer structured $InSb$ films. It was found that the mobility increments in both cases are due to the matching of the stoichiometry in $InSb$ films. For the heat treated and passivated specimens, the mobilities increased with annealing time and the maximum mobility was measured as 1612 $cm^2$/Vs.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.119-125
• /
• 2016

This study examined the running dynamic characteristics of a hybrid type wheel-rail high speed train, in which the propulsion method of maglev is applied. A wheel-rail high speed train propelled by a superconducting linear synchronous motor (SC-LSM) is expected to be superior to a maglev train regarding economical and interoperable aspects, still having powerful thrust force as maglev. In this paper, regarding the two methods of applying the SC-LSM to an existing wheel-rail train, to investigate the influences of SC-LSM propulsion on the dynamic characteristics of wheel-rail high speed train, the dynamic model of train including interaction between the rotor and stator of SC-LSM is established. Through the simulation using the model, the influence of the interaction between the rotor and stator of SC-LSM on stability, ride comfort and the effect of guideway irregularity are investigated.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1055-1057
• /
• 2002

산업이 발전할수록 정밀 위치제어 알고리즘에 대한 요구가 증가하고 있으며, 선형 전동기의 보급에 따라 1um 단위의 고급 위치 제어 알고리즘에 대한 중요성이 커지고 있다. 위치제어에 있어서 작업의 신속성 및 정밀도를 높이기 위해서는 제어의 오버슛 현상을 억제할 필요가 있으며, 현장에서 직접 활용이 가능하도록 하려면 보다 간단한 구조의 제어 알고리즘이 요구된다. 위치제어에서 가장 큰 문제는 전동기의 최대 속도 및 최대 전류 제한에 의한 비선형성이 위치의 과도한 오버슛으로 나타난다는 것이며, 기존의 고급 알고리즘에서는 미리 제공되는 S-커브 형태의 위치 명령 패턴을 사용하여 속도 및 전류 제한을 회피하고 있다. 본 연구에서는 고급 제어 알고리즘과 동일한 성능을 내면서 복잡한 패턴 생성기를 사용하지 않고도 실제 위치가 오버슛없이 부드러운 S-커브 형태로 목표값에 수렴하는 새로운 형태의 위치제어기를 제안한다. 제안된 제어기는 비교적 간단한 구조로 인하여 헌장 적용력이 매우 뛰어나며, 이득 설정이 간편하다는 장점을 지니고 있다.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.3 no.4
• /
• pp.244-254
• /
• 1991

The numerical analysis on tile behaviour of mooring system in the offshore guyed tower is presented. The governing equilibrium equations are derived by the principle of virtual work. The drag and inertia effects of fluid are included in a Morrison type equation. The finite element method is used in the computation. Geometric nonlinearities for the analysis of the mooring line are considered in which both modified Newton-Raphson method and Newmark-$\beta$ method are employed. Numerical experiments show the validity and the capability of the developed mathematical formulation.