• Korean Journal of Optics and Photonics
• /
• v.14 no.4
• /
• pp.413-422
• /
• 2003

We have calculated the power extraction efficiency and the lasing wavelength distribution of index-coupled DFB lasers at threshold for various kL and facet reflectivity combinations, and compared with those above-threshold. The power extraction efficiency increases as the asymmetry of the facet reflectivities increases. The power extraction efficiency above-threshold is slightly larger than that at threshold. Since the relative photon density around the center region increases as kL increases, the power extraction efficiency decreases. The uniformity of the distribution of lasing wavelength over the stop band increases due to the relief of mode degeneracy as the asymmetry of the facet reflectivities increases. In the case of AR-HR combination, the lasing wavelength distributions at threshold are similar to those above-threshold. However, in the case of AR-AR combination, the lasing wavelength at threshold is concentrated on both edges of the stop band, while it is concentrated only on the longer wavelength edge above-threshold. As kL increases, the range of the lasing wavelength distribution increases due to the increase of the stop band. The effect of AR reflectivity on the power extraction and the lasing wavelength distribution is very weak.

• Fire Science and Engineering
• /
• v.25 no.2
• /
• pp.80-87
• /
• 2011

On the result of load-bearing fire test to confirm the fire resistance of a composit beam, if the composit beam has lower fire resistance than required standard, it can be improved by section change. But if there are many types of section change, it takes much time and cost owing to conducting many tests. On this study, it was confirmed which part of the asymmetric H-section composit beam affected most on fire resistance by heat-transfer analysis. Then, we checked the tendency of improving fire resistance depend on section change by heat-transfer and non-linear structural analysis and suggested a changed section having 1-hour fire resistance.

• Journal of Korean Society of Steel Construction
• /
• v.28 no.1
• /
• pp.43-52
• /
• 2016

A numerical study on required stiffness of the longitudinal stiffener in the webs stiffened with flat plate at one-side of the web was conducted. The longitudinal stiffeners are commonly placed around 0.2D, i.e., 1/5 the web depth due to fabrication convenience although most plate girders for bridges are unsymmetric section. Considering asymmetry of section, aspect ratio of web and the rigidity ratio of longitudinal stiffener(${\gamma}^*$), eigenvalue analysis were performed to evaluate the buckling strength for the webs with a stiffener located at 0.16D~0.24D. Based on the parametric analysis, the required stiffness of the longitudinal stiffener to satisfy the buckling strength specified in AASHTO LRFD specifications was presented.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.7 no.4
• /
• pp.1-13
• /
• 2003

For spatial free vibration of non-symmetric thin-walled curved beams with shear deformation, an improved formulation is proposed in the present study. The elastic strain and the kinetic energies are first derived by considering constant curvature and shear deformation effects due to shear forces and restrained warping torsion. Next equilibrium equations and force-deformation relations are obtained using a stationary condition of total potential energy. And the finite element procedures are developed by using isoparametric curved beam element with arbitray thin-walled sections. Particularly not only shear deformation and thickness-curvature effects on vibration behaviors of curved beams but also mode transition and crossover phenomena with change in curvatures of beams are parametrically investigated. In order to illustrate the accuracy and the reliability of this study, various numerical solutions for spatial free vibration are compared with results by available references and ABAQUS's shell element.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.2
• /
• pp.291-298
• /
• 1994

This paper presents a new stiffness matrix for the analysis of arbitrary thin-walled open beams in warp-restrained torsion. The element accounts for both flexural and warping torsional effects. To eliminate the ad hoc introduction of St. Venant stiffness in this $C^0$ element, the virtual work equation based on an orthogonal Cartesian coordinate system is used. The effectiveness of the derived block stiffness is addressed. The transformation matrix between two different reference systems is also shown. Numerical examples using the proposed matrix are compared with the classical solutions or other previous results in the literature.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.10
• /
• pp.4706-4712
• /
• 2013

One of the efficient procedures for the solution of partial differential equations is the method of differential quadrature. This method has been applied to a large number of cases to circumvent the difficulties of programming complex algorithms for the computer, as well as excessive use of storage due to conditions of complex geometry and loading. Under in-plane uniform distributed load, the buckling of asymmetric curved beam with varying cross section is analyzed by using differential quadrature method (DQM). Critical load due to diverse cross section variation and opening angle is calculated. Analysis result of DQM is compared with the result of exact analytic solution. As DQM is used with small grid points, exact analysis result is shown. New result according to diverse cross section variation is also suggested.

• The Korean Journal of Petroleum Geology
• /
• v.7 no.1_2 s.8
• /
• pp.7-12
• /
• 1999

A new high-resolution rnagnetotelluric (MT) survey was conducted for pull-apart basin analysis (Cretaceous Eumsung Basin), combined with surface sedimentological results. Two cross-basinal MT profiles represent an asymmetric form with a subbasin in the southeastern part. These basinal architectures are well compatible with paleoflow directions and facies transitions of surface sedimentology. The results also suggest that the basin fills reflect pull-apart opening with rapid subsidence of the central blocks. Combined with the surface sedimentological data on asymmetric lithofacies distribution, facies transitions, and paleoflow directions of the alluvio-lacustrine systems, the MT data help explain basin-fill processes during the basin formation. For petroleum exploration and basin analysis, the high-frequency MT technique can be a useful substitute for the costly burden of a seismic-reflection survey on land.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.37 no.2
• /
• pp.333-342
• /
• 2017

In order to understand the mechanism of the cross-shore evolution of storm (barred) and normal (nonbarred) profiles of a sandy beach, the vertically two-dimensional laboratory experiment was performed with a movable bed. The beach profiles and free surface motion were measured under monochromatic wave conditions evolving the storm and normal beach profiles. The observation was conducted in the surf zone during the alternation of the two wave conditions to reach its quasi-equilibrium state. The sandbar-crest and trough and the steep berm were evolved due to the plunging breakers in the storm case, and the bar-trough was decayed due to the spilling breakers in the normal case. From the measurements, it was found that the storm wave case was in an erosion state and the normal wave case was in an accretion state. The strong undertow, which is a dominant factor of the offshore migration mechanism, was developed in the storm wave case, and the weak undertow was developed in the normal wave case. The skewness and the asymmetry of the nonlinear wave motion, which is a dominant factor of the onshore migration mechanism, was measured similarly in both cases.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.4
• /
• pp.357-366
• /
• 2007

This paper is a pilot study regarding an experimental and parametric study to investigate the structural behavior of slimfloor beam(ASB) in fire. The objective of this research is to obtain the rational fire resistance design method through understanding the structural behavior of composite members in fire. The flexural capacity of slimfloor section under various thermal conditions is examined on a basis of the strength retention of the materials at elevated temperatures and full bonding assumption. The effect of web thickness and ASB depth to the moment capacity in fire is also examined.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.6 no.1
• /
• pp.25-33
• /
• 1986

Natural river channels usually have a deep section and one or two floodplains, which is called a compound channel. As the general method in the compound channel overestimates the discharge capacity, the momentum transfer due to interaction between the main channel flow and flow over its floodplain must be considered. Scale model experiments are performed for the rectangular main channel with an asymmetrical floodplain. Firstly, velocities are measured at various section grids. Secondary, boundary shear stresses are calculated from velocity distributions. Lastly, in order to determine the apparent shear force, the shear stress distributions are integrated along the wetted perimeter for the full cross-section and equated to the total weight force in the flow direction. The hydraulic characteristics in a compound channel are closely examined with the scales of length, velocity, boundary shear stress, and apparent shear force which are described with the various relationships.