• Proceedings of the Korea Society of Environmental Toocicology Conference
• /
• 2001.05a
• /
• pp.135-135
• /
• 2001

수돗물 불소화사업이란 치아우식증 (충치)을 예방할 목적으로 0.8ppm의 불소를 수돗물에 첨가하는 공중보건사업이며, 수돗물 불소화사업이 시행되지 않고 있는 서울시내 초등학교에서는 1995년부터 불화나트륨용액 (0.2%용액으로 매주 1회 또는 0.05%용액으로 매일 1회)으로 불소양치를 실시하고 있으며, 서울시 일부 보육시설에서는 만4세-6세의 취학전 아동을 대상으로 불소용액양치사업 (0.25% 용액)을 1997년부터 실시하고 있다. (중략)

• Polymer(Korea)
• /
• v.25 no.3
• /
• pp.343-348
• /
• 2001

The mechanical and the platelet adhesion properties of the fluorinated polyurethane elastomers synthesized with a perfluorinated polyether diol (Fomblin ZDOL$ZDOL^{(R)}$) and 4,4'-diphenyl methane diisocyanate (MDI) were investigated. The change of mechanical properties with the Fomblin content and the type of the polyether diol was investigated by applying a designed technique using in vitro platelet adhesion test. As a result, the tensile properties were affected by the content and the type of nixed polyether diols. Also the platelet adhesion of polyurethane elastomers decreased with increasing the extent of fluorination in the polymer.

• Applied Chemistry for Engineering
• /
• v.27 no.4
• /
• pp.386-390
• /
• 2016

The surface of carbon nanotubes (CNTs) was modified by fluorination and applied to conductive materials to improve the energy efficiency of a capacitive desalination (CDI) electrode. CNTs were fluorinated at room temperature with a mixed gas of fluorine and nitrogen, and activated carbon based CDI electrodes were then prepared by adding 0-0.5 wt% of untreated CNTs or fluorinated CNTs with respect to the activated carbon. Fluorinated CNTs showed improved dispersibility in the electrode and also slurry as compared to untreated CNTs, which was confirmed by the zeta potential and scanning electron microscopy. Fluorinated CNTs added electrodes showed higher desalination efficiency but lower energy consumption than those of using untreated CNTs added electrodes. This was attributed to the decrease in the resistance of CDI electrodes due to the improved dispersibility of CNTs by fluorination.

• Applied Chemistry for Engineering
• /
• v.32 no.1
• /
• pp.55-60
• /
• 2021

Fluorination was carried out to improve the adsorption performance of pitch-based activated carbon fibers (ACFs) onto acetic acid. Both plasma and direct gas fluorination were used for fluorination, and the acetic acid gas adsorption performance of fluorinated ACFs was investigated. X-ray photoelectron spectroscopy (XPS) is analyzed to determine the surface characteristics of ACFs, and the pore characteristics were analyzed by 77 K nitrogen adsorption. An adsorption performance was measured through gas chromatography, and it was confirmed that the breakthrough time of plasma fluorinated sample was 790 min and that the breakthrough time was delayed compared to that of using untreated one of 650 min. However, the breakthrough time of direct gas fluorinated sample was 390 min, indicating that the adsorption performance was inhibited. The plasma fluorinated ACFs showed an increase in the adsorption performance due to an electrostatic attraction between the acetic acid gas (CH3COOH) with the fluorine group introduced to the surface without changing its specific surface area. On the other hand, the specific surface area of the direct gas fluorinated ACFs decreased significantly up to 55%, and the physical adsorption effect on the acetic acid gas also reduced.

• Applied Chemistry for Engineering
• /
• v.33 no.2
• /
• pp.159-165
• /
• 2022

To enhance the photocatalytic activities of WO₃ photocatalysts, fluorine doping was performed to induce the oxygen vacancies. Both plasma and direct vaper fluorination were carried out for fluorine doping, and photocatalytic activities were examined by using methylene blue dye. Oxygen vacancies of the plasma and direct vaper fluorinated WO₃ photocatalysts were measured to be 14.65 and 18.59%, which increased to about 23 and 56% at pristine WO₃ photocatalysts. The degradation efficiency of methylene blue was also determined about 1.7 and 3.4 times higher than pristine WO₃ photocatalysts, respectively, depending on oxygen vacancies increased. In addition, it was confirmed that the bandgap process energy decreased from 2.95 eV to 2.64 and 2.45 eV after fluorine doping. From this result, it is considered that the direct vaper fluorination has an advantage for increasing the photocatalytic activities of WO₃ compared to that of the plasma fluorination.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.47-51
• /
• 2011

In this study, illite, an environmental friendly, low cost, and high aspect ratio additive, was used to improve flame retardant property of epoxy and it was fluorinated to enhance dispersion of hydrophilic illite in hydrophobic epoxy by introducing hydrophobic functional groups. Fluorination of illite enhanced illite dispersion ill epoxy solution before curing and that in the complex after curing. These enhanced dispersions were attributed to the increased affinity of illite to hydrophobic epoxy solution induced by fluorination of illite and the increased intercalation of epoxy polymer or exfoliation of illite by epoxy curing. Hence, limited oxygen index(LOI) of fluorinated illite/epoxy complex increased by 24%, compared to that of epoxy, suggesting that the preparation of fluorinated illite/epoxy complex increased their flame retardant properties.

• Membrane Journal
• /
• v.25 no.5
• /
• pp.447-455
• /
• 2015

In this study, Polysulfone (PSf) and polyetherimide (PEI) as the anion exchange polymers were aminated in the different ratio whereas the polyether ether ketone (PEEK) as the cation exchange polymer was sulfonated. The bipolar membranes of SPEEK (sulfonated PEEK)/APSf (aminated PSf) and SPEEK/APEI (aminated PEI) were prepared by the double-casting method. The surfaces of bipolar membranes were fluorinated in accordance with the amination ratio and applied to produce the hypochlorite. As the amination increased, the hypochlorite concentration is also increased. Typically, for SPEEK/APSf 3 : 1 membrane, the produced hypochlorite concentration was 61.0 ppm and its durability was 220 min for the non-fluorinated membrane while for the fluorinated membrane, the concentration of 58.6 ppm and its durability lasted 570 min. Also for SPEEK/APEI 3 : 1 membrane, the hypochlorite concentrations of 60.1 ppm and 58.3 ppm for before- and after-fluorination, respectively were observed whereas the durability was remarkably developed from 150 min to 440 min. Therefore, the surface fluorination takes an important role for the development of the membrane durability.

• Applied Chemistry for Engineering
• /
• v.32 no.6
• /
• pp.653-658
• /
• 2021

Polyvinylidene fluoride (PVDF) is a promising coating material because of its outstanding processability. The PVDF coating, however, has limitations in anti-corrosion application due to its weak hydrophobicity compared to that of other fluoropolymers. In this study, plasma fluorination was performed using carbon tetrafluoride (CF₄) gas to improve anti-corrosion properties of PVDF. The fluorine content and hydrophobicity of PVDF were investigated in different CF₄ flow rates, followed by the determination of anti-corrosion properties. The fluorine content on the surface of the PVDF film increased by up to 46.70%, but the surface free energy was independent of CF₄ flow rate. Meanwhile, the surface roughness of the PDVF film tended to increase by up to 150% and then decrease with increasing CF₄ flow rate. It is considered that the plasma fluorination affects the surface free energy due to the introduction of fluorine functional groups and surface etching. In addition, the degree of corrosion of the PVDF-coated Fe plate was significantly reduced from 49.2% to 19.0% compared to that of the uncoated Fe plate. In particular, the degree of corrosion of the fluorinated PVDF-coated Fe plate was 13.6%, which was 28.4% lower than that of the PVDF-coated Fe plate, showing improved anti-corrosion protection.

• Applied Chemistry for Engineering
• /
• v.26 no.1
• /
• pp.92-98
• /
• 2015

In this study, phenol-based activated carbons (ACs) were fluorinated at various fluorine partial pressures (0.01~0.03 MPa) and the $Cr^{6+}$ ion adsorption of fluorinated ACs was investigated. According to BET and XPS results, the specific surface area and total pore volume of fluorinated ACs increased by 24.7 and 55.8%, respectively, and fluorine functional groups were introduced to AC surface. The most optimized condition of $Cr^{6+}$ ion adsorption was confirmed at the fluorine partial pressure of 0.02 MPa. And also the removal efficiency of $Cr^{6+}$ ion was up to 98% at 300 mg/L of the initial concentration, and these results showed an approximately three-fold increase compared to that of using untreated ACs. Furthermore, the $Cr^{6+}$ ion adsorption of fluorinated ACs was completed in less than 30 min in contrast with untreated ACs, which was expected to be an increase of the affinity between $Cr^{6+}$ ions and ACs surfaces by fluorination.

• Applied Chemistry for Engineering
• /
• v.29 no.6
• /
• pp.677-681
• /
• 2018

In this study, the carbon block was prepared using the fluorinated coke and binder pitch by molding compression to increase its density. After fluorination, it is confirmed that the fluorine element on the coke surface was introduced up to 24.14 at% using XPS analysis. The wettability between the fluorinated coke and binder pitch was evaluated according to the reaction temperature. From the result of contact-angle tests, it can be found that the wettability was improved up to 64.7% as more fluorine atoms were introduced on the surface of cokes. Also, the density of the carbon block with the highest amount of fluorine increased with 6.8% compared to that of using the carbon block prepared by the untreated cokes.