• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.2
• /
• pp.161-167
• /
• 2009

The regulation of the $CO_2$ emit from vehicles have become much more stringent in recent years. This stringent regulation is more request vehicle manufacturers to develop the alternative fuel vehicles for reducing exhaust emissions. LPG fuel is more clean energy compares with gasoline and diesel fuel. Especially, $CO_2$ emission of LPG Vehicle is less than gasoline vehicle and almost equal to diesel vehicle. For this reason, recently korean government is extending LPG fuel for hybrid car and light duty vehicle. In domestic, Propane is mixing $15{\sim}30%$ to butane for improvement of cold start at winter season. Therefore, In this paper was investigated that the characteristics of emissions according to propane mixing rate with 0, 10, 20, 30% were compared and analyzed by the vehicle test using LPG vehicle according to the FTP75 mode. It was also investigated the characteristics of nano-particle emit with propane mixing rate.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2245-2250
• /
• 2003

Particulate matters(PM) have bad effect on the health. We carried out measurements of diesel PM under $10{\mu}m$ diameter from a HSDI diesel engine with a diesel oxidation catalyst(DOC) by using the ELPI. This paper compares the two results of the smoke level and the PM level of masses and numbers. We also investigated the effect of the DOC. Under high speed and load, HSDI diesel engine exhausts much masses of particulate matters over 100nm diameter, and a number of PM from 7 to 100nm diameters at the same condition. DOC could reduce the total mass of the PM. However, the DOC could increase the number of ultra fine PM. Before light-off of the soot, the DOC absorb the PM and the DOC oxidize the PM after light-off temperature. The fine PM could be made during the oxidation. Therefore, the advanced DOC is needed to reduce the number of the fine PM.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.230-231
• /
• 2005

본 논문은 광 활성도가 가장 좋은 아나타제(anatase) 상의 광촉매 $TiO_2$ 분말을 상온에서 aerosol deposition 법을 사용하여 박막을 제조하였다. 이런 제조 방법은 aerosol 분말을 초음속으로 분사하여 기판에 증착시키는 방법으로, 저온에서 박막 증착이 가능하여 thermal stress를 줄일 수 있고, 공정 단가를 낮출 수 있다는 장점이 있다. 박막 제조시 aerosol bath의 압력은 500 torr이고, chamber의 압력은 0.4 torr였다. 이런 압력차는 0.4mm$\times$10mm의 크기의 노즐을 통해 $TiO_2$ 나노 분말을 초음속으로 가속하여 기판에 증착시켰다. 박막 제조를 위해 사용한 기판은 수질정화에 응용하기 위해 직경 50mm인 원판 SUS 멤브레인을 사용하였다. SUS 멤브레인 위에 증착되어 있는 $TiO_2$ 박막의 입자 크기와 조성을 알아보기 위해 주사 현미경 (SEM) 및 EDX 분석을 하였고, l$\mu$m 정도의 입자 크기와 수처리 후에도 표면에 증착 되어진 anatase 상의 $TiO_2$ 박막을 확인할 수 있었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.7
• /
• pp.593-602
• /
• 2016

Numerical simulations on the close-coupled supersonic gas atomizer for metallic powder production were performed in this study. A proper turbulence model was chosen and then VOF(Volume of Fluid) and DPM(Discrete Phase Model) methods were sequentially applied for the simulations of primary and secondary break-up processes of liquid metal. Diameters of parent droplets were calculated by analyzing Level-Set function contour from the VOF result. Finally, the distribution of particle diameter was obtained from the DPM result at exit of the computational domain.

• Journal of Drive and Control
• /
• v.21 no.1
• /
• pp.8-15
• /
• 2024

This thesis investigates the jetting characteristics of an aerosol jet printing (AJP) process as a function of design and operating conditions. The governing equations of the AJP system are derived for experimentation and analysis. To understand the characteristics of the AJP system, it analyzes the jetting characteristics as a function of the flow rate of the carrier gas and the sheath gas, and the variation of the linewidth with the nozzle exit size based on particle tracking. The thesis focuses on computational fluid dynamics (CFD), which is a computer simulation. The particle tracking results obtained by CFD were analyzed using MATLAB. CFD analytical models can be analyzed in environments with different conditions and consider more specific situations than mathematical computational models. The validity of the CFD analysis is shown by comparing the experimental results with the CFD analysis.

• Journal of Drive and Control
• /
• v.21 no.2
• /
• pp.8-14
• /
• 2024

This paper investigates the jetting characteristics of an aerosol jet printing (AJP) process as a function of design and operating conditions. The governing equations of the AJP system are derived for experimentation and analysis. To understand the characteristics of the AJP system, this thesis analyzes the jetting characteristics as a function of the flow rate of the carrier gas and the sheath gas, and the variation of the linewidth with the nozzle exit size based on particle tracking. This thesis focuses on computational fluid dynamics (CFD), which is a computer simulation. The particle tracking results obtained by CFD were analyzed using MATLAB. CFD analytical models can be analyzed in environments with different conditions and consider more specific situations than mathematical computational models. The validity of the CFD analysis is shown by comparing the experimental results with the CFD analysis.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.7
• /
• pp.773-778
• /
• 2015

Global warming has recently become an issue that has resulted in a growing trend to minimize environmental pollution. The International Maritime Organization (IMO) has shown that the majority of marine atmospheric pollution occurs as a result of emissions from marine vessels. Therefore, the environmental regulations and emission standards regarding marine vessels have gradually become stricter, and the research and development in this area is experiencing significant progress. In this study, a nozzle for a fuel oil scrubber was investigated using computational fluid dynamics (CFD) and particle imaging velocimetry (PIV). Experiments were conducted on scaled-down model of the scrubber to determine its performance, which was then compared with CFD results. Based on the experimental results, it was found that at a spray angle of $66^{\circ}$, the spray velocity at the nozzle was 20.1 m/s. From this comparison, a full-scale scrubber model was analyzed using CFD, and the effect of the positioning of the nozzle was studied.

• Journal of the Korea Computer Graphics Society
• /
• v.24 no.3
• /
• pp.101-109
• /
• 2018

Recently, the improvement of virtual reality and augmented reality technologies leverages many new technologies like the virtual study room, virtual architecture room. Such virtual worlds require free handed drawing technology such as writing descriptions of formula or drawing blue print of buildings. In nature, lots of view point modifications occur when we walk around inside the virtual world. Especially, we often look some objects from near to far distance in the virtual world. Traditional drawing methods like using fixed size image for drawing unit is not produce acceptable result because they generate blurred and jaggy result as view distance varying. We propose a novel method which robust to the environment that produce lots of magnifications and minimizations like the virtual reality world. We implemented our algorithm both two dimensional and three dimensional devices. Our algorithm does not produce any artifacts, jaggy or blurred result regardless of scaling factor.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.4334-4340
• /
• 2012

In this work, we developed and evaluated the Liquid Particle Generator for generating fine particles in the air. The Liquid Particle Generator, which was based on the spray-evaporation method, had two kinds of orifices: 0.3 mm and 0.5 mm. The Liquid Particle Generator was operated at different pressure between 1 bar and 4 bars to find relationship between input pressure and droplet output rate. In addition, the size distribution of the droplets generated by the Liquid Particle Generator with different orifices was measured by the SMPS system and the optical particle counter. As a result, it was shown that the Liquid Particle Generator with 0.3 mm orifice generated droplets of around 0.3 ${\mu}m$ and atomized particles very stably. The Liquid Particle Generator having 0.5 mm orifice generated bigger droplets, compared with the Liquid Particle Generator with 0.3 mm orifice. Additionally, in these Liquid Particle Generators (0.3 mm and 0.5 mm orifice), little coagulation of particles did occur because of fine droplets atomized by the jet. Therefore, the Liquid Particle Generator could be used as an aerosol generator for atomizing fine particles.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.67.2-67.2
• /
• 2017

본 연구에서는 $SiO_2$ 미세구조 상에 Pd 나노입자(NPs)를 증착하여, 불소화된 마이크로-나노 계층구조를 갖는 Pd-decorated $SiO_2$($Pd/SiO_2$)를 제작하였다. 마이크로 크기의 거칠기를 갖는 $SiO_2$ 층은 졸-겔 공정을 사용해서 제조된 용액을 전기분사함으로써 제조되었다. 이어서, 자외선(UV)을 이용한 광 환원법을 이용해 Pd 나노입자를 $SiO_2$ 층에 형성했다. 생성된 표면은 마이크로-나노의 계층구조 형태를 보여주었다. 해당 시편의 불소화 처리 후, 마이크로-나노의 계층구조 표면은 $170^{\circ}$ 이상의 물 접촉각(water contact angle; WCA) 및 $5^{\circ}$ 이하의 슬라이딩 각(sliding angle)을 보여줌으로써 물에 대해 탁월한 소수성을 나타내었다. 또한, 커피($CA=161^{\circ}$), 우유($CA=162^{\circ}$), 쥬스($CA=163^{\circ}$), 그리고 글리세롤($CA=165^{\circ}$)에 대해서도 우수한 소수 특성을 보여주었다. 또한, 이들 $Pd/SiO_2$ 층은 우수한 장기내구성 및 자외선 저항성을 보여주었다. 그리고 이어진 기름에 대한 접촉각 측정을 통해 해당 시편이 소유 특성이 아닌 친유 특성을 보여준다는 것을 확인할 수 있었고, 기름에 대한 CA는 약 ${\sim}10^{\circ}$로 매우 우수한 친유 특성을 나타내었다. 이와 같은 결과는 자체세정이 가능한 표면 및 지능형 물/기름 분리 시스템과 같은 스마트 장치에서 초소수성-친유성 특성을 갖는 계층구조의 $Pd/SiO_2$ 층을 사용할 가능성을 명확하게 보여준다고 판단된다.