• Journal of the Korean Society of Propulsion Engineers
• /
• 제5권1호
• /
• pp.34-41
• /
• 2001

A study has been conducted to observe the slot film cooling effect on a convergent nozzle wall. The slot film cooling is used to protect the nozzle wall from the hot combusted gas by the coolant injected from the slot around the inner wall of the nozzle. The film cooling effectiveness and the heat transfer to the nozzle wall are influenced significantly by the blowing ratio of the coolant to the main flow and those are also influenced by the shape of the slot and the flow acceleration in the nozzle. In the present study, the heat transfer for the various blowing ratios has been performed by the experimental method and the results are compared with the results computed by the empirical formula. The numerical method has been conducted to compare the film cooling effectiveness of the convergent nozzle with that of the cylinder. For the relatively low blowing ratio, the cooling effectiveness increases sharply as the blowing ratio increases, and the increasing rate slows down for the high blowing ratio.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.949-952
• /
• 2017

Spray characteristics of the impinging injectors in subsonic crossflows were experimentally studied and compared with the plain-orifice injectors. By changing the impingement angle (60, 90, 120) which is the same orifice length to diameter ratio (L/d = 5), spray characteristics were investigated. In the view of the top view from the impinging injectors, as the impingement angle increases, the liquid column breakup length in the y-direction was decreased. On the other hand, when the impinging injector is viewed from the side view, the breakup length in the x direction is smaller than the previous plain-orifice injectors, which mean that the atomizing performance of the impingement-type injector is better than that of the single-hole orifice.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• 제38권9호
• /
• pp.890-899
• /
• 2010

An experimental study has been conducted to analyze the operating forces on a partially admitted turbine blade using a linear cascade apparatus. Axial-type blades were used and the blade chord was 200mm. The rectangular nozzle was applied and its size was $200mm{\times}200mm$. The experiment was done at $3{\times}10^5$ of Reynolds number based on the chord. The rotational force and axial force on the blade were measured at steady state by moving the blade to the rotational direction. The operating forces were measured at three different nozzle install angles of $58^{\circ}$, $65^{\circ}$ and $72^{\circ}$ for off-design performance test. In addition, three different solidities of 1.25, 1.38 and 1.67 were applied. From the results, the maximum rotational force was increased when the solidity was decreased and the nozzle install angle was decreased. The axial force was increased by decreasing the nozzle install angle. The reverse axial force was obtained in the partially admitted region when the nozzle install angle was increased to $72^{\circ}$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• 제7권4호
• /
• pp.798-804
• /
• 2003

In this paper, We have designed an advanced circuits for controlling the Ink Nozzle of Printer Head We can fully increase the number of nozzle by reducing the number of Input/Output PADs using the proposed new circuit. The proposed circuit is tested with only 20 nozzles to evaluate functional test using FPGA sample chip. The new circuit architecture can be estimated. Full circuit for controlling 320 nozzles was designed and simulated from ASIC full custom methodology, then the circuit was fabricated by applying 3${\mu}{\textrm}{m}$ CMOS process design rule.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• 제12권3호
• /
• pp.41-47
• /
• 2013

This study was carried out to improve the design of fuel injection nozzle for marine medium speed diesel engine. For this purpose, fuel injection nozzle was modeled and simulated using CATIA V5R19 and FLUENT & MSC Nastran. Analyses of flow and heat transfer, respectively, were performed to find the optimal design of fuel injection nozzle. As the results, big pressure drop, which may lead to cavitation damage, was occurred at inlet of fuel injection hole with diameter 0.3mm. Furthermore, it was confirmed that the increase of mean temperature of fuel injection nozzle was almost a half in comparison with that of fuel injection nozzle tip.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• 제35권8호
• /
• pp.706-713
• /
• 2007

The jet structure issuing from a conventional convergent nozzle of variable expansion rate is compared with the result from the nozzle of a constant expansion rate using a normal type annular slit. In experiments, to investigate the jet characteristics between the two cases of jet, the mean velocity of nozzle exit is fixed to be 90m/s, the pressures along the jet axis and radial directions are measured by a scanning valve system moving with 3-axis auto-traverse unit, and the velocity distribution obtained by calculation from the measured static and total pressures is compared. Also to obtain the highly stable and convergence jets, it is turned out that the flow through a nozzle of constant expansion rate using the Coanda effect with an annular slit is the most preferable than that case through variable expansion rate nozzle. Furthermore, it is found that the pressure drop along the nozzle for the constant expansion rate nozzle is small relatively against to the case of variable expansion rate nozzle.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• 제22권4호
• /
• pp.201-213
• /
• 1989

This study is just to be carried out to grasp the efficiency of jet stream excavating for the ground. Changing the dynamic pressure, nozzle diameter, distance off the ground, we measured the impulse, the excavated depth, the excavated width. According as each dynamic pressure increases from 100 to $500gf/cm^2$, the impulse of the jet stream increases from 43 to 114gf, from 52 to 227gf, from 114 to 506gf, from 137 to 768gf, in 4, 6, 8, 10mm nozzles respectively, but it makes no difference in the value of distance within 50cm off ground. The excavated depth increases at the invariable rate in accordance with nozzle diameter, dynamic pressure, nozzle distance. We obtain the equations relevant to the ground I, II as follows: $$L_I=[0.01(H/r-100) -0.43\cdot\iota+11.78]{\cdot}D/4$$ $$L_{II}=[0.03(H/r-100) -0.34\cdot\iota+6.39]{\cdot}D/4$$ where, $L_I,\;L_{II}$ are respectively the excavated depths of the ground I, II, cm; H is the dynamic pressure, $gf/cm^2\;:\;\iota$ is the distance off the ground, cm; D is Nozzle diameter, mm; r is the specific weight, $1gf/cm^2$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제17권11호
• /
• pp.363-367
• /
• 2016

A test section of a supersonic wind tunnel was designed for the analysis of flow characteristics over a backward-facing step with Mach 1.0 slot injection in a supersonic flow of Mach 2.5. The cavity flow of a high-speed vehicle is very complex at supersonic speed, so it is necessary to do experiments using supersonic wind tunnels to verify numerical analysis methods. The previous 2D symmetrical nozzle was replaced with an asymmetrical nozzle. The inviscid nozzle contour was designed using Method of Characteristics (MOC), and the boundary layer thickness correction was reflected by experimental data from the wind tunnel. The results were compared with a CFD analysis. The PID control system was changed to be based on the change of tank pressure. This improved the control efficiency, and the run times of supersonic flow increased by about 1 second. The flow characteristics over a backward facing step with slot injection were visualized by a Schlieren device. This equipment will be used for an experimental study of the film cooling effectiveness over a cavity with various velocities, mass flows, and temperatures.

• Journal of the Korean Society of Propulsion Engineers
• /
• 제10권3호
• /
• pp.41-47
• /
• 2006

Effects of mean flow and nozzle damping on acoustic tuning of a gas-liquid scheme coaxial injector are investigated numerically adopting a linear acoustic analysis. The injector plays a role as a half-wave acoustic resonator for acoustic damping in a combustion chamber of a liquid rocket engine. As Mach number of mean flow in a chamber increases, the resonant frequency of the first tangential mode decreases slightly and the optimum injector tuning length varies negligibly. Nozzle damping affects neither the resonant frequency nor the optimum length. From these numerical results, effects of mean flow and nozzle damping on acoustic tuning of a resonator are negligible. As open area of the injectors increases, the acoustic amplitude decreases, but new injector-coupled modes appear.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제34권10호
• /
• pp.933-939
• /
• 2010

The purpose of this study is to investigate the generation and development of cavitation in circular and elliptical nozzles. In order to investigate the influence of cavitation, the experiment was conducted with a set of elliptical nozzles that had the same cross-sectional area, different orifice aspect ratios (a/b). Each nozzle was made of acrylic so that visualization was possible. With the injection pressure, the internal flow of the nozzle was classified into the no-cavitation, cavitation, and hydraulic-flip regions. Regardless of the nozzle geometry, with the injection pressure, the flow rate in the no-cavitation and cavitation regions increased and the discharge coefficient decreased. However, the flow rate was constant in the hydraulic-flip region. In the elliptical nozzles, the generation and development of cavitation occurred at higher cavitation number than that in the case of a circular nozzle.