• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.450-454
• /
• 1997

This system is the automatic boiler tube bending equipment which has four heads for bending the tube and the carriage for moving the tube. The system consists of two frames for transporting each moving parts, high-frequency heating equipment for heating the tube in hot bending, control panel for inputting the job data operating, remote control unit for concetration and distribution of input/output, and the monitoring system which can establish unmanned operationby receiving the bending job data via LAN form a design teamwhich produces the job data and schedule based on master production plan and diagnoses bending data change, input, whole system status, and system malfunctions. By employing this system, 30% of production improvement was achieved was achieved comparing to the existing bending system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.1
• /
• pp.10-16
• /
• 2004

In this thesis, improved full wave mode ZVT(Zero-Voltage-Transition) PMW DC-DC Converters are presented to maximize the regeneration ratio of resonant energy by only putting an additional diode In series with the auxiliary switch. The operation of the auxiliary switch in a half wave mode makes it possible soft switching operation of all switches including the auxiliary switch whereas it is turned off with hard switching in conventional converter. The increase of the regeneration ratio to resonant energy results in low commutation losses and minimum voltage and current stresses. The operation principles of the improved ZVT PWM DC-DC Converters are theoretically analyzed using the boost converter topology as an example. Both theoretical analysis and experimental results verify the validity of the PWM boost converter topology with the improved full wave mode ZVT PWM converters.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.7
• /
• pp.74-80
• /
• 2006

This paper describes a solar energy conversion strategy is applied to grid-connected single phase inverter by the maximum power point of conversion strategy. The maximum power point of tracking is controlled output power of PV(photovoltaic)modules, based on generated circuit control MOSFET switch of two boost converter for a connected single phase inverter with four IGBT's switch in full bridge. The generation control circuit allows each photovoltaic module to operate independently at peak capacity, simply by detecting of the output power of PV module. Furthermore, the generation control circuit attenuates low-frequency ripple voltage. which is caused by the full-bridge inverter, across the photovoltaic modules. The effectiveness of the proposed inverter system is confirmed experimentally and by means of simulation.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2036-2038
• /
• 1998

In the buck-boost DC-DC chopper which is used at a certain situation such as in factories where loads often change a lot, the switches in the device make big energy loss in operating at Buck-Boost Mode due to hard switching and are affected by lots of stresses which decrease the efficiency rate of the converter. In order to improve this problem, to decrease the loss of snubber and switching, it has been investigated that zero voltage switching mode and zero current switching mode which make the operation of switches with soft switching. For the more sophisticated and advanced device, this paper is presented the Partial Resonant Soft Switching Mode Power Converter which is adapted the power converter having the partial resonant soft switching mode, that makes switches operate when the resonant current or voltage becomes zero by making the resonant circuit partially at turning on and off of the switches with suitable layout of the resonant elements and switch elements in the converter. Also, this paper includes the analysis and simulation of the Partial Resonant type Buck-Boost Chopper.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.6
• /
• pp.101-109
• /
• 2005

Ultra-precision positioning systems basically require high natural frequency and sufficient workspace. To cope with this requirement, flexure hinge mechanisms have been proposed. However, previous designs are hard to satisfy the functional requirements of the system due to difficulty in modeling and optimizing process applying an independent axiomatic design. Therefore, this paper proposes a new design and design-order based on semi-coupled axiomatic design. A planar 3 DOF parallel type micro mechanism is chosen as an exemplary device. Based on preliminary kinematic analysis and dynamic modeling of the system, an optimal design has been carried out. To check the effectiveness of the optimal parameters obtained from theoretical approach, simulation is performed by FEM. The simulation result shows that a natural frequency of 200.53Hz and a workspace of $2000{\mu}m{\times}2000{\mu}m$ can be ensured, which is in very close agreement with the specified goal of design.

• Journal of Biomedical Engineering Research
• /
• v.20 no.1
• /
• pp.21-27
• /
• 1999

In order to increase our understanding of the injury mechanism in the child occupant, three year old child model was developed using commercial dynamic package DADS. Total 14 segments and 12 joints were used to compose a model in three points belted condition with booster seat. HYGE sled test case was simulated to validate the developed model. Based on the comparison of the model and published test results, the developed model appears to be a resonable representation of the three year old dummy.

• Journal of Navigation and Port Research
• /
• v.31 no.10
• /
• pp.839-844
• /
• 2007

This paper describes the performance of DC-DC converters for buoy such as buck, boost, and buck-boost. The operating characteristic and charging efficiency with battery, which has a considerable properties about converters with PV(photovoltaic) system, is analyzed in this paper. It is performed by using the MPPT(Maximum Power Point Tracker) algorithm The basic equations of switching operation for converter are described, and the equations are analyzed with according to switch state. Whereas this analysis is directed toward the selection of converter for buoy, it also provides the insight into the behaviour of converter and performance of the proposed algorithm Finally, the suitable DC-DC converter is proposed for buoy, and the characteristic experiment is performed with the buck converter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.6
• /
• pp.531-538
• /
• 1999

This paper proposes a fuzzy logic controller(FLC) for DC-DC converters in order to obtain good l perfonnances that can not be achieved by linear control tc'Chniques in the presence of wide parameter v variations. 'While the standard controller uses error and derivative of e$\pi$or, the proposed controller uses state v variables. Such method is ve$\pi$ efficient in case of DC-DC converters and can guarantee both stable s small-signal responses and improved large signal responses. The presented approach method is general and c can be applied to any dc-dc converter topologies. Through the simulations of booster, we verify the pro[Xlsed C control tc'Chnique can give a satisfactory perfonnance.

• The Journal of the Korea Contents Association
• /
• v.3 no.2
• /
• pp.78-86
• /
• 2003

The Minisoy of Information and Communication(MIC) requires telecompanys to share base stations in order to prevent the duplicated investment and environmental destruction which would be caused by the indiscreet construction of basestations for enlarging their own service area among telecompanys. This paper discusses' the problems of mobile communication services that have been generated in common-repeater at the Metropolitan subway. These problem include factors of power obstacles, communication equipment and establishment obstacles. The content of this paper is helpful in organizing the basestation sharing of IMT-2000 and the 4th generation mobile system, and provides the basics of a higher quality service for common-service communication.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.1
• /
• pp.58-67
• /
• 2021

This paper describes the development for the dual thrust rocket motor with two types of propellants with different combustion characteristics. We developed the composition of two kinds of propellant to be applied to a rocket motor, and improved a propellant charging process in a free grain type to improve the adhesion method and the problems of adhesion between different propellants. In addition, to meet the ignition phenomenon as a small rocket motor, the ignition delay was improved by applying a nozzle plug developed in a high density foam. The propulsion rocket motor reflecting this design and the improved manufacturing process was evaluated through a ground performance test.