• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.4
• /
• pp.6-13
• /
• 2011

Due to its robustness to illumination change, normalized cross-correlation based similarity measurement is widely used in many machine vision applications. However, its inefficient computation structure is not adequate for real-time embedded vision system. In this paper, we present an efficient hardware architecture based on a normalized cross correlation (NCC) for fast image similarity measure. The proposed architecture simplifies window-sum process of the NCC using the integral-image. Relieving the overhead to constructing integral image, we make it possible to process integral image construction at the same time that pixel sequences are inputted. Also the proposed segmented integral image method can reduce the buffer size for storing integral image data.

• Korean Journal of Remote Sensing
• /
• v.27 no.4
• /
• pp.403-410
• /
• 2011

Consistent observation with high temporal and spatial resolution is required for an efficient monitoring of coastal environments. Remote monitoring system installed on the ground is capable of simultaneous observation of wide coastal area and consistent observation with high frequency, which a small number of in-situ measurements cannot manage. This paper studies two typical ground based coastal monitoring system, marine radar and camera system. Marine radar can produce time series of frequency spectrum by integrating wave number spectrum calculated from spatial and temporal variation of waves in the radar image. The time averaged radar images of waves can analyze wave breaking zone, rip currents and location of littoral bars. Camera system can observe temporal variation of foam generation originated from coastal contamination as well as shoreline changes. By extracting the part of foams from rectified images, quantitative analysis of temporal foam variation can be done. By using the two above systems of different characteristics, synergetic benefit can be achieved.

• Journal of Korean Society of Transportation
• /
• v.21 no.3
• /
• pp.71-83
• /
• 2003

An arterial street control is performed for the purpose of the progression of a traffic flow using the arterial. However during the progression in the arterial, the change according to the time is one of the most representative problems occurring at a signal plan. This paper intends to efficiently operate the arterial progression by applying fuzzy logic, which is thought to be the most possible one in the inference as that of the human logic, to the traffic responsive control system. Fuzzy Logic controller is appliable to the daily human language (linguistic). can be dealt with the uncertain traffic data and is useful on planning the signal control to sensitively confront the randomly changing traffic condition. This study, based on the signal control part of the isolated intersection in "A Development of a Real-time, Traffic Adaptive Control Scheme Through VIDs"(Seong Ho. Kim. 1996). suggested the strategy for the progression control in the arterial and analyzed its effect by comparing the effect of the existing control method. In addition, the study compared each effect by using TRAF-NETSIM which is the traffic simulation software to analyze each control method.

• Progress in Medical Physics
• /
• v.22 no.4
• /
• pp.190-197
• /
• 2011

Currently, the dose distribution calculation used by commercial treatment planning systems (TPSs) for high-dose rate (HDR) brachytherapy is derived from point and line source approximation method recommended by AAPM Task Group 43 (TG-43). However, the study of Monte Carlo (MC) simulation is required in order to assess the accuracy of dose calculation around three-dimensional Ir-192 source. In this study, geometry factor was calculated using segmented sources integration method by dividing microSelectron HDR Ir-192 source into smaller parts. The Monte Carlo code (MCNPX 2.5.0) was used to calculate the dose rate $\dot{D}(r,\theta)$ at a point ($r,\theta$) away from a HDR Ir-192 source in spherical water phantom with 30 cm diameter. Finally, anisotropy function and radial dose function were calculated from obtained results. The obtained geometry factor was compared with that calculated from line source approximation. Similarly, obtained anisotropy function and radial dose function were compared with those derived from MCPT results by Williamson. The geometry factor calculated from segmented sources integration method and line source approximation was within 0.2% for $r{\geq}0.5$ cm and 1.33% for r=0.1 cm, respectively. The relative-root mean square error (R-RMSE) of anisotropy function obtained by this study and Williamson was 2.33% for r=0.25 cm and within 1% for r>0.5 cm, respectively. The R-RMSE of radial dose function was 0.46% at radial distance from 0.1 to 14.0 cm. The geometry factor acquired from segmented sources integration method and line source approximation was in good agreement for $r{\geq}0.1$ cm. However, application of segmented sources integration method seems to be valid, since this method using three-dimensional Ir-192 source provides more realistic geometry factor. The anisotropy function and radial dose function estimated from MCNPX in this study and MCPT by Williamson are in good agreement within uncertainty of Monte Carlo codes except at radial distance of r=0.25 cm. It is expected that Monte Carlo code used in this study could be applied to other sources utilized for brachytherapy.

• Journal of Korea Spatial Information System Society
• /
• v.11 no.2
• /
• pp.119-132
• /
• 2009

Owing to the GIS technology, a vast volume of spatial data has been accumulated, thereby incurring the necessity of spatial data mining techniques. In this paper, we propose a new spatial data mining system named SD-Miner. SD-Miner consists of three parts: a graphical user interface for inputs and outputs, a data mining module that processes spatial mining functionalities, a data storage model that stores and manages spatial as well as non-spatial data by using a DBMS. In particular, the data mining module provides major data mining functionalities such as spatial clustering, spatial classification, spatial characterization, and spatio-temporal association rule mining. SD-Miner has own characteristics: (1) It supports users to perform non-spatial data mining functionalities as well as spatial data mining functionalities intuitively and effectively; (2) It provides users with spatial data mining functions as a form of libraries, thereby making applications conveniently use those functions. (3) It inputs parameters for mining as a form of database tables to increase flexibility. In order to verify the practicality of our SD-Miner developed, we present meaningful results obtained by performing spatial data mining with real-world spatial data.

• Journal of the Korea Computer Graphics Society
• /
• v.16 no.3
• /
• pp.1-10
• /
• 2010

In this paper, we propose a novel noiseless method of BRDF rendering on a GPU in real-time. Illumination at a surface point is formulated as an integral of BRDF producted with incident radiance over the hemi-sphere domain. The most popular method to compute the integral is the Monte Carlo method, which needs a large number of samples to achieve good image quality. But, it leads to increase of rendering time. Otherwise, a small number of sample points cause serious image noise. The main contribution of our work is a new importance sampling scheme producing a set of incoming ray samples varying continuously with respect to the eye ray. An incoming ray is importance-based sampled at different latitude angles of the eye ray, and then the ray samples are linearly connected to form a curve, called a thread. These threads give continuously moving incident rays for eye ray change, so they do not make image noise. Since even a small number of threads can achieve a plausible quality and also can be precomputed before rendering, they enable real-time BRDF rendering on the GPU.

• Journal of Korean Society of Transportation
• /
• v.18 no.5
• /
• pp.33-42
• /
• 2000

This Paper is a Part of research Project series to analyze unique traffic characteristics observable within weaving sections on urban freeways. The research objectives were to establish with headway distribution and maximum Passing volume on weaving sections the basis of weaving designs that can promote safety and efficiency. Until now, when one wants to check the maximum Passing volume on weaving sections, it is taken for granted using headway distribution of freeway basic section. However. it was suspected in this research that for weaving sections different form of headway distribution had better be used. To prove this, field surveys were made to count headway intervals which supposedly were influenced not only by freeway basic section flows but also by weaving flows and later on used to develop headway distribution for weaving sections. For validation of the developed headway distribution, $x^2$-test was applied to three different data set of observed headways, currently used headway distribution for basic sections(Pearson Type III distribution) and new headway distribution. The result indicated new headway distribution as the most appropriate distribution form. Also, maximum passing volume within weaving sections was calculated based on new headway distribution and compared with Drew's maximum Passing volume.

• Journal of Korea Water Resources Association
• /
• v.43 no.8
• /
• pp.733-745
• /
• 2010

Seasonality of hydrologic extreme variable is a significant element from a water resources managemental point of view. It is closely related with various fields such as dam operation, flood control, irrigation water management, and so on. Hydrological frequency analysis conjunction with partial duration series rather than block maxima, offers benefits that include data expansion, analysis of seasonality and occurrence. In this study, nonstationary frequency analysis based on the Bayesian model has been suggested which effectively linked with advantage of POT (peaks over threshold) analysis that contains seasonality information. A selected threshold that the value of upper 98% among the 24 hours duration rainfall was applied to extract POT series at Seoul station, and goodness-fit-test of selected GEV distribution has been examined through graphical representation. Seasonal variation of location and scale parameter ($\mu$ and $\sigma$) of GEV distribution were represented by Fourier series, and the posterior distributions were estimated by Bayesian Markov Chain Monte Carlo simulation. The design rainfall estimated by GEV quantile function and derived posterior distribution for the Fourier coefficients, were illustrated with a wide range of return periods. The nonstationary frequency analysis considering seasonality can reasonably reproduce underlying extreme distribution and simultaneously provide a full annual cycle of the design rainfall as well.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.11A
• /
• pp.1827-1840
• /
• 2001

In digital data transmission/storage systems, the compensation for channel distortion is conducted normally using a training sequence that is known a priori to both the sender and receiver. The use of the training sequences results in inefficient utilization of channel bandwidth. Sometimes, it is also impossible to send training sequences such as in the burst-mode communication. As such, a great deal of attention has been given to the approach requiring no training sequences, which has been called the blind equalization technique. On the other hand, to utilize the limited bandwidth effectively, the concept of partial response (PR) signaling has widely been adopted in both the high-speed transmission and high-density recording/playback systems such as digital microwave, digital subscriber loops, hard disk drives, digital VCRs and digital versatile recordable disks and so on. This paper is concerned with blind adaptive equalization of partial response channels whose transfer function zeros are located on the unit circle, thereby causing some problems in performance. Specifically we study how the problems of blind channel equalization associated with the PR channels can be improved. In doing so, we first discuss the existing methods and then propose new structures for blind PR channel equalization. Our structures have been extensively tested by computer simulation and found out to be encouraging in performance. The results seem very promising as well in terms of the implementation complexity compared to the previous approach reported in literature.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.438-443
• /
• 2002

본 연구는 수도작에서 토양과 식물체의 분광반사특성과 영상처리를 이용한 기계시각 잡초검출 센서를 개발하기 위한 기초연구로서 분류하고자 하는 대상체들의 분광반사율을 조사하여 주요한 파장을 선정하고 선정된 파장을 이용한 판별분석을 통해 각 대상체에 대한 분류 정확도를 중심으로 잡초검출 가능성을 조사하기 위하여 수행하였으며, 실험으로부터 얻은 결론은 다음과 같다. 1. 토양과 식물체를 구분하는데 효과적인 파장은 마른 토양의 경우 680 nm, 배수 토양에 있어서는 810 nm로 선정하였고, 토양을 배제한 후 벼와 잡초를 구분하기에 효과적인 파장은 580, 680 nm로 선정하였다. 2. 토양과 식물체를 구분하기 위한 판별분석 결과 2가지 토양상태 모두 식물체와 완전히 구분 가능한 것으로 나타났다. 벼와 잡초를 구분하기 위한 실험에서, 벼는 98%의 분류정확도로 구분이 가능하였고, 잡초는 83%의 분류정확도로 구분이 되는 것으로 나타났다. 따라서 차후 분광학적 원리를 이용한 센서를 제작할 때 본 연구에서 선택한 주요 파장과 판별함수를 이용하여 장치를 구성하고 알고리즘을 제작한다면 벼, 잡초, 토양을 효과적으로 구분이 가능할 것으로 판단되었다. 3. 컬러 CCD 카메라를 사용하는 경우에 있어 식물체와 토양을 구분하기 위해 3 종의 파장 중 630 nm 파장만의 이용을 고려하여 그 분류성능을 분석한 결과, 식물체와 토양은 소수의 관측치를 제외하고 완전히 구분이 가능했고, 벼와 잡초를 구분한 결과에서는 비교적 높은 분류능력을 가진 것으로 나타나 차후 컬러 CCD 카메라를 이용하여 장치를 구성하는데 좋은 기초가 될 것으로 판단된다. 배양체의 접종작업은 모든 배양실이 인력에 의존하였으며, 배양체를 배지와 분리하여 불필요한 부분을 제거하고 배양작물에 따라 생육정도를 2~3등급으로 구분하여 배양용기의 배지 위에 치상하는 과정으로 수행되었으며, 작업능률은 호접란의 경우 배양병에 25본을 접종하는데 시간당 6병, 심비디움은 원형 플라스크에 25본을 접종하는데 시간당 10병 정도였다. 바. 식물체의 대량증식에 사용되는 플라스크, 배양병, PE용기 등 배양용기의 세척작업은 농원의 1개배양실에서 간이식 세척기, 이 외의 9개배양실은 모두 물에 담겨 두었다가 세제와 브러쉬 등을 사용하여 인력으로 세척하고 있어 생력화 기술개발이 요구되었다.도가 빠를수록 건조속도가 빨라졌으며, 건조에너지도 1,334kcal/kg.water로 비슷하게 소요되었다. 마. 시험구와 대비구의 건감률은 시험구에서 1.08~1.36w.b./h로 나타나 대비구보다 약 9.9~18.3%가 높게 나타났고, 건조에너지는 10.2~14.6%가 절감되었다. 발아율은 열풍온도가 낮을수록 높게 나타났고 시험구가 대비구보다 발아율이 낮게 나타났으며, 동할률 증가량도 원적외선.열풍 복합건조방법이 높게 나타나 이것은 곡물 표면에 원적외선 방사에의한 복사열이 전달되어 열장해를 받았기 때문으로 판단되며, 금후 더 연구하여 적정 열풍온도 및 방사체 크기를 구명해야 할 것이다.으로 보여진다 따라서 옻나무 유래 F는 포유동물의 생식기능에 중요하게 작용하는 것으로 사료된다.된다.정량 분석한 결과이다. 시편의 조성은 33.6 at% U, 66.4 at% O의 결과를 얻었다. 산화물 핵연료의 표면 관찰 및 정량 분석 시험시 시편 표면을