• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.204-209
• /
• 1999

각종섬유를 연속섬유 보강재로 사용하는 경우, 일반적으로 수지를 매트릭스로 하여 봉재 형상(FRP rod)으로 제조하고있다. 성형된 섬유는 수지가 섬유의 보호재 역할을 하기 때문에, 콘크리트내의 알칼리와 절연되어 열화가능성이 작다고 고려된다. 그러나, 일반적으로 섬유를 둘러싼 수지는 그 두께가 수 {$mu}m$이하로 특히 얇고, 운반이나 보관시에 수지가 물리적 변형 및 자외선에 의한 열화가 일어날 가능성이 높다. 또 알칼리에 의하여 에스테르의 가수분해반응에 따른 폴리머의 부식 등, 수지에 알칼리의 침입을 완전히 막는 것이 불가능하게 여겨진다.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1948-1950
• /
• 2000

Polymeric composite insulators have been in use for outdoor insulation. However, our knowledge about their long-term performance in an outdoor environment is still very limited. Especially, these insulators are subjected to the environmental stress such as ultraviolet radiation, electrical stress, mechanical load, etc.. Hence, in this paper, we simulated the factors having influence on aging of polymer insulators using the combined aging test chamber. In order to evaluate an aging characteristics with time, we measured leakage current on these insulators to make out the degree of aging.

• Corrosion Science and Technology
• /
• v.8 no.2
• /
• pp.53-61
• /
• 2009

In this study, both evaluations by visual imaging for exterior view of coating and by EIS were executed for epoxy primer coated specimens deteriorated by accelerated test, and comparison and analysis were carried out for 2 evaluation methods. In the comparison between total damaged area ratio acquired by image processing method and deterioration point, higher deterioration points were appeared for rusted specimens than for non-rusted specimens. It is attributed that deterioration point per unit area ratio given for rust is higher than for peeling. In the comparison between total damaged area ratio and EIS result, impedance of coating was largely decreased as about TEX>$10^4{\Omega}{\cdot}cm^2$ or less when rust area ratio is more than about 0.1%, and blistering area ratio is more than about 3%. Charge transfer resistance ($R_{ct}$) and double layer capacitance ($C_{dl}$) values were appeared for all specimens except 2 ones, which shows that water is accumulated and steel substrate is corroded at coated film-steel interface. In the comparison between deterioration point and EIS result, more than 10 points as deterioration point were given for specimens of below $10^6{\Omega}{\cdot}cm^2$ of impedance at low frequency. For specimens deteriorated by NORSOK cyclic test, impedance was lowest of all, though deterioration point was not high. It is thought to be attributed that coating system and accelerated deterioration condition of cyclic tested specimens were different from those of main specimens. From the result, it is thought that coating resistance can be relatively more decreased than deterioration degree estimated from exterior view under more severe corrosion environment or in the present of more complex deterioration factors.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.2
• /
• pp.150-156
• /
• 2011

In this paper, infrared thermography measurement technique has been used to develop standard measurement technique for nondestructive testing of composite materials which is widely used in aerospace industries. To increase the defect detection rate, the related experiment used the lock-in IR-thermographiy method. Therefore it is of considerable interest in the field of non-destructive testing for fast discontinuity detection by using ultrasonic lock-in infrared thermography. The result also shows that as the investigation period of light source is lengthened according to the thickness of specimen, the possibility of detecting defects gets higher as well. However, the reason why the result values were not favorable when less than 50 mHz of light source was provided is because it was difficult to detect defects as the defect parts became a state of thermal equilibrium in general when thermal diffusivity affects the entire materials.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.8 no.2
• /
• pp.165-182
• /
• 2006

In this study, field test was performed to investigate the strength-improvement effect of shotcrete mixed Micro-silica fume and shotcrete quality was estimated by EFNARC standard. Deterioration test combined the Freezing-thawing and Carbonation was also performed in order to investigate a long-term durability of high-strength shotcrete. As a result of test, the compressive strength of shotcrete using Micro-silica fume was 45.2~55.8MPa and flexible strength was 5.01~6.66MPa, so a promotion ratio of strength was 37~79%, 17~61% respectively. And the strength-improvement effect of strength by silica fume addition ratio of 7.5~10% for cement mass was more superior to the others. Due to relative dynamic modulus, mass decrease rate and carbonation progress of shotcrete mixed Micro-silica fume, it was especially realized that Micro-silica fume reduced deterioration caused by steel fiber and improved a long-term durability of shotcrete.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.3
• /
• pp.115-122
• /
• 2006

Ten types of steel bars having different Cr contents were embedded in concretes with chloride ion contents of 0.3, 0.6, 1.2, and $2.4kg/m^3$ to fabricate specimens assuming such deteriorative environments. After being carbonated to the reinforcement level, these concretes were subjected to corrosion-accelerating cycles of heating/cooling and drying/wetting. The time-related changes in the corrosion area and corrosion loss of the Cr-bearing rebars were then measured to investigate their corrosion resistance. The results revealed that in a deteriorative environment prone to both carbonation and chloride attack, corrosion resistance was evident with a Cr content of 7% or more and 9% or more in concretes with chloride ion contents of 1.2 and $2.4kg/m^3$, respectively.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.8
• /
• pp.711-718
• /
• 2011

The thermoelastic behavior of the porous carbon/phenolic composites is studied using the thermomechanical response model of chemically decomposing composites. The model includes thermal dependence of the porous composites, porosity in the pyrolysis process, pore pressure due to decomposing gases, and shrinkage. The poroelastic coefficients are calculated based on representative volume element model and finite element analysis. The internal stress distribution caused by pores and pore pressure, and the overall deformation are verified. The effects of the poroelastic coefficients on the thermoelastic behavior are examined through numerical experiments.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.5
• /
• pp.1064-1070
• /
• 2012

Nowadays, image processing has been applied in a variety of fields. In order to preserve the high quality of visual the degradation phenomenon for images should be removed. Noise is one of the representative elements cause of the degradation phenomenon and AWGN(additive white Gaussian noise) always damages images. In this paper, an mixed filter algorithm, which is based on parallel denoising method, is proposed to suppress AWGN. This algorithm parallels the spatial domain wiener filter and the wavelet domain thresholding method which thresholding function is selected based on scale level. The proposed modified thresholding function which considers the dependency between parent and child coefficient performs well on suppressing noise.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.537-540
• /
• 2008

Up to now, the RC structures have been recognized as being socially semi-permanent. But in recent years there were reports about the cases of early deterioration of RC structures. Most of all pore structure effects on the durability of concrete as well as mechanical properties of concrete. Therefore, in this study, mixing design was proportioned with the water-binder ratio 0.55 binder compositions corresponding to cement without any supplementary materials(OPC), cement with 50% blast-furnace slag replacement (BFS50), cement with 15% fly ash replacement (FA15), and ternary cement with cement, 15% fly ash, and 35% slag replacement (BFS35+FA15). And this study is to compare pore structure property of concrete by carbonation to investigate the effect of the permeation of deterioration factors such as $CO_2$ and chloride ion under the combined deterioration environments. The results showed that pore volume effects on the diffusibility of chloride ion.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3437-3443
• /
• 2013

The polymer insulators have been extensively used as an alternate material of ceramic insulators. However, when they are used in practical conditions, there are many problems of decreasing performance and shortening lifetime due to the exposures of degradation factors applied from the outdoor situations. Accordingly, the analysis of polymer degradations has been getting influential too late as one of important subjects for improvements of safety and reliability. Heat, water treatments are arbitrary simulated for finding out the initiations and processes of surface degradation on the polymer surface. Especially, this study is focused on the chemical changes properties. From the analysis of hydrophilic and hydrophobic molecular structures, final modeling of surface degradation is accomplished. We checked the contact angle depending on heat and moisturized accelerated degradation and ran an XPS analysis to check the mechanism change of the surface of the PCB polymer composite. The surface that had a tendency to attract moisture showed a decrease in the contact angle and generated a large amount of carboxyl($-COO^*$) radicals. The hydrophobized surface showed an increase in the contact angle and had a stable chemical composition constituted of the breakaway of oxygen radicals and the formation of double bond by carburization.