• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.7 s.110
• /
• pp.648-658
• /
• 2006

We propose a thin frequency selective surface(FSS) superstrate etched on a substrate for dual-band directivity enhancement, and present a design method of the superstrate. In the proposed new design, two FSS arrays with the same periodicity, but with different alignments are placed above and below a thin dielectric layer to overcome the problem of conventional superstrates for dual band directivity enhancements. Based on the unit-cell simulation, several important parameters that characterize the thin FSS superstrate are investigated, and the procedure for designing such a superstrate is described. We compare the resonant frequencies and the qualify factors of the unit cell with those of three FSS antenna composites with different quality factors, and identify the quality factors which support similar directivity enhancement at the dual-band directivity enhancement. It was found that there is an optimum FSS array size of a superstrate to enhance the directivity most efficiently. Measured results for a fabricated superstrate show a good agreement with the simulated ones.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.5A
• /
• pp.317-325
• /
• 2012

In this study, to evaluate the shrinkage behavior of ultra high performance fiber reinforced concrete (UHPFRC) under restrained condition, restrained shrinkage test was performed according to ring-test mostly used at home and abroad. Ring-test was performed with the various thicknesses and radii of inner steel ring to give different degree of restraint. Free shrinkage and tensile tests were carried out simultaneously to estimate the degree of restraint, stress relaxation, and shrinkage cracking potential. Test results indicated that the average steel strain and residual tensile stress were reduced as the thicker inner steel ring was used, whereas degree of restraint was increased. The steel strain, residual tensile stress and degree of restraint were hardly affected by the size of radius of inner ring. In the case of all ring specimens, shrinkage crack did not occur because the residual tensile stress was lower than the tensile strength. About 39~65% of the elastic shrinkage stress was relaxed by the sustained interface pressure, and the maximum relaxed stress was increased as the thicker inner ring was applied. Finally, the degree of restraint with age was predicted by performing non-linear regression analysis, and it was in good agreement with the test results.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• autumn
• /
• pp.529-532
• /
• 2003

Efficiency and efficient management on maintenance/repair/operation (MRO) phase is getting important with advance in technologies and complex functionalities of building and facility. Using software systems as well as advanced hardware systems in MRO area is spreading along with this trend to take advantage of information technology. Information of building and facility for MRO phase is derived from engineering/procurement/construction (EPC) phase. But most current commercial software systems in EPC and MRO are focusing on their own phase, which arise lack of consistency of information from EPC to MRO phase. But, the information system now used at the MRO phase stop flowing the building and the facilities information and then newly create. Moreover, from all asset management point of view, asset particulars such as the structures and equipments are different the value fluctuation. In order to reflect these information rationally, the construction costs are correctly distributed and the initial price of the asset particulars have to be estimated. In this study, develop the information model which can apply the cost information at the EPC phase to the MRO phase.

• Korean Journal of Construction Engineering and Management
• /
• v.5 no.1 s.17
• /
• pp.99-106
• /
• 2004

Efficiency and efficient management on maintenance/repair/operation (MRO) phase is getting important with advance in technologies and complex functionalities of building and facility, Using software systems as well as advanced hardware systems in MRO area is spreading along with this trend to take advantage of information technology. Information of building and facility for MRO phase is derived from engineering/procurement/construction (EPC) phase. But most current commercial software systems in EPC and MRO are focusing on their own phase, which arise lack of consistency of information from EPC to MRO phase. But, the information system now used at the MRO phase stop flowing the building and the facilities information and then newly create. Moreover, from an asset management point of view, asset particulars such as the structures and equipments are different the value fluctuation. In order to reflect these information rationally, the construction costs are correctly distributed and the initial price of the asset particulars have to be estimated. In this study, develop the information model which can apply the cost information at the EPC phase to the MRO phase.

• Journal of the Korean earth science society
• /
• v.21 no.6
• /
• pp.719-733
• /
• 2000

Normally, a digital geologic map can be defined as mappable one whose spatial information with geographic information details and geologic database attribute, recorded in a digital format that is readable by computer. It shows fundamentally two different conceptual perspectives: cartography for digital mapping and analysis for geo-data processing. While, as both aspects basically relate to natural entities and their interpretation of complex features fused with multi-sources, digital geo-data mapping or geologic mapping, it should be distinguished from digital mapping in engineering such as UIS(Urban Infomation System) and AM/FM(Automated Mapping/Facilities Management). Furthermore, according to short-cycled development of GIS(Geographic Information System) software architecture based on IT(Information Technology) and wide expansion of GIS applications' fields, the importance of domain analysis and application model is emphasized at digital geologic informatizaion. In this paper, first terms and concepts of geo-data model with general data modeling aspects are addressed, and then case histories for geo-data modeling and several approaches for data modeling in GIS application fields are discussed. Lastly, tentative conceptual geo-data modeling by using UML(Unified Modeling Language) of OO(Object-oriented) concepts with respect to USGS/AASG geo-data mode is attempted. Through this approach, the main benefits for standardization and implementation lineage with conceptual model in consideration to reusability are expected. Conclusively, it is expected that geo-information system and its architecture by UML is the new coming key approach for the GIS application in geo-sciences.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.1
• /
• pp.31-35
• /
• 2017

The mechanical characteristics of frozen sand greatly depend on the frozen temperature and the fine contents according to the previous study by Chae et al. (2015). There are two hypotheses to explain this experimental results; one is the unfrozen water contents greatly affected by the fine contents and frozen temperature and the other is the sand particle spacing greatly affected by the pore-ice. To evaluate the latter hypothesis, the micro X-ray CT scan was performed. The micro X-ray CT scanning, one of the actively performed interdisciplinary research area, has a high resolution with micrometer unit allows to investigate internal structure of soils. In this study, X-ray CT technique was applied to investigate the effect of the frozen temperature and fine contents on the sand particle minimum and average spacing with the developed image processing techniques. Based on the spacing analysis, the frozen temperature and fine contents have little influence on the sand particle spacing in the frozen sand specimens.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.4
• /
• pp.13-16
• /
• 2013

A lot of various researches have been going on to use heat spreader for LED module. Nano porous aluminum anodic oxide (AAO) applied LED, which is produced from anodization, is easy and economically advantageous. Convensional LED module is consist of aluminum/adhesive/copper circuit. The polymer adhesive in this module is used as heat spreader. However the thermal emission of LED component is degraded because of low heat conductivity of polymer and also reliability of LED component is reduced. Therefore, AAO in this work was applied to heat spreader of LED module which has higher heat conductivity compare to polymer. Bonding strength between AAO and copper circuit was improved with Ti/Cu seed layer by copper sputtering process (DBC) before the bonding. And this copper circuit has been fabricated by electro plating method. Peel strength of AAO and copper circuit in this work showed range between 1.18~1.45 kgf/cm with anodizing process which is very suitable for high power LED application.

• Composites Research
• /
• v.30 no.3
• /
• pp.181-187
• /
• 2017

The effect of nanoscopic and microscopic Fe, $Fe_3O_4$, and Ni particles and their shapes and substrate materials on the heating behavior of thermoplastic polyurethane (TPU) adhesive films was investigated via induction heating. The heat generation tendency of $Fe_3O_4$ particles was higher than that shown by Fe and Ni particles in the TPU adhesive films. When the Fe and Ni particle size was larger than the penetration skin depth, the initial heating rate and maximum temperature increased with an increase in the particle size. This is attributed to the eddy current heat loss. The heating behavior of the TPU films with Ni particles of different shapes was examined, and different hysteresis heat losses were observed depending on the particle shape. Consequently, the flake-shaped Ni particles showed the most favorable heat generation because of the largest hysteresis loss. The substrate materials also affected the heating behavior of the TPU adhesive films in an induction heating system, and the thermal conductivity of the substrate materials was determined to be the main factor affecting the heating behavior.

• Journal of Digital Convergence
• /
• v.12 no.2
• /
• pp.1-10
• /
• 2014

Recently, the value and the status of the digital archives that are built individually in the crossroads of oblivion and memory are due to big data has attracted attention globally is confusing. Video data that contains the cultural memory of the digital archive, such as culture, art, life, society, and social conditions of the time, it is a cultural heritage of national common expressed. Also, it remains a trace of history from the various media just like magazines, books, painting, photography, and film. Digital archive system is one of the best research results of media convergence and it has also a good opportunity to take full advantage of the new opportunities and cultural assets. The collection of infinite information of big data in perspective transient that exist at the same time compatibility of big data, it is trying to dismantle the cultural memory of us. It was asserted that must meet the criteria which can correspond to via the new digital era, will be applied to preserve the traditional media. The current image archive is necessary to accommodate proper two different directions.

• Korean Journal of Construction Engineering and Management
• /
• v.11 no.3
• /
• pp.23-32
• /
• 2010

Construction Projects have mutual collaborative structures among various participants for common objectives. Most of all the design project which is the initial phase in the project is crucial for determining project overall quality and requires intimate and continuous relations between project participants. Thus, this study suggests Design Collaboration Management System for successful performing projects through cooperation among participants in the initial stage of projects. First, expert interviews were performed to figure out present conditions of design collaboration management and problems. The factor analysis was applied to draw owner's collaboration factors and engineer's collaboration factors. Based on those factors, this study suggests design cooperation management process which gives a framework for systematic management method. Through the process the design collaboration management system was developed which helps owner/designers/engineer's co-work. The System suggested from this study realizes systematic information management tool and through that it is expected to improve design product;'s quality, and further contribute the advancement of project.