• Transactions of the Korean Society of Mechanical Engineers
• /
• v.4 no.3
• /
• pp.105-112
• /
• 1980

정현적 응력을 받고 있는 정탄성 결합부의 에너지 손실을 여러 가지 인자를 고려하여 구하였다. 탄성접착결합부의 해를 구하고 탄성해의 전단계수를 복소전단계수로 대치하여 점탄성 접착결 합부의 전단변형분포를 구하였다. 주어진 접착제의 최대강쇠현상은 접착제의 강성과 피접착물의 비를 증가 시킴으로서 얻을 수 있다. 구조적 결합부에서 파괴가 일어나지 않도록 피접착부와의 강성비를 결정함에 있어 주의를 요한다.

• Restorative Dentistry and Endodontics
• /
• v.34 no.5
• /
• pp.450-459
• /
• 2009

The aim of this study was to measure the initial dynamic modulus changes of light cured composites using a custom made rheometer. The custom made rheometer consisted of 3 parts: (1) a measurement unit of parallel plates made of glass rods, (2) an oscillating shear strain generator with a DC motor and a crank mechanism, (3) a stress measurement device using an electromagnetic torque sensor. This instrument could measure a maximum torque of 2Ncm, and the switch of the light-curing unit was synchronized with the rheometer. Six commercial composite resins [Z-100 (Z1), Z-250 (Z2), Z-350 (Z3), DenFil (DF), Tetric Ceram (TC), and Clearfil AP-X (CF)] were investigated. A dynamic oscillating shear test was undertaken with the rheometer. A certain volume ($14.2\;mm^3$) of composite was loaded between the parallel plates, which were made of glass rods (3 mm in diameter). An oscillating shear strain with a frequency of 6 Hz and amplitude of 0.00579 rad was applied to the specimen and the resultant stress was measured. Data acquisition started simultaneously with light curing, and the changes in visco-elasticity of composites were recorded for 10 seconds. The measurements were repeated 5 times for each composite at $25{\pm}0.5^{\circ}C$. Complex shear modulus G*, storage shear modulus G', loss shear modulus G" were calculated from the measured strain-stress curves. Time to reach the complex modulus G* of 10 MPa was determined. The G* and time to reach the G* of 10 MPa of composites were analyzed with One-way ANOVA and Tukey's test ($\alpha$ = 0.05). The results were as follows. 1. The custom made rheometer in this study reliably measured the initial visco-elastic modulus changes of composites during 10 seconds of light curing. 2. In all composites, the development of complex shear modulus G* had a latent period for $1{\sim}2$ seconds immediately after the start of light curing, and then increased rapidly during 10 seconds. 3. In all composites, the storage shear modulus G" increased steeper than the loss shear modulus G" during 10 seconds of light curing. 4. The complex shear modulus of Z1 was the highest, followed by CF, Z2, Z3, TC and DF the lowest. 5. Z1 was the fastest and DF was the slowest in the time to reach the complex shear modulus of 10 MPa.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.1
• /
• pp.9-17
• /
• 2011

In this paper, the general equation of motion of damped sandwich beam with multi-viscoelastic material layer was derived based on the equation presented by Mead and Markus. The viscoelastic layer, which has characteristics of complex shear modulus, was assumed to be dominantly under shear deformation. The equation of motion of n-layered damped sandwich beam in bending could be represented by (n+3)th order ordinary differential equation. Finite element model for the n-layered damped sandwich beam was formulated and programmed using higher order shape functions. Several numerical examples were implemented to show the effects of damped material.

• Composites Research
• /
• v.13 no.4
• /
• pp.67-74
• /
• 2000

The general solution of the anti-plane shear problem for the curved interfacial crack between viscoelastic foam and composites was investigated with the complex variable displacement function. Kelvin-Maxwell three parameter model is used to present viscoelasticity and the Laplace transform was applied to treat the viscoelastic characteristics of foam in the analysis. The stress intensity factor near the interfacial crack tip was predicted by considering both anisotropic and viscoelastic properties of two different materials. The results showed that the stress intensity factor increased with increasing the curvature of the curved interfacial crack and it also increased and eventually converged to a specific value with increasing time. The stress intensity factor increased with increasing the ratio of stiffness coefficients between foam and composites and the effect of fiber orientation on the stress intensity factor decreased with increasing the ratio of stiffness coefficients between foam and composites.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.2
• /
• pp.110-122
• /
• 1996

본 논문에서는 전기유동유체(Electro-Rheological Fluid : ERF)를 함유하는 지능구조물의 동적 모델링 및 진동제어를 수행하였다. 먼저 실리콘 오일을 기본용매로 하여 조성된 ERF의 복소 전단모듈러스를 전장부하와 가진 주파수의 함수로 동적 회전모드 실험을 통하여 도출한 후, 이를 샌드위치 보 이론과 연계하여 동적 모델링을 실시하였다. 도출된 6차 편미분방정식 형태의 지배 방정식을 유한요소 모델로 이산화하여 전장부하에 따른 지능구조물의 동탄성 특성값인 감쇠 고유 주파수 및 모달 손실계수를 주파수 영역에서 얻었다. 그리고 ERF를 함유한 샌드위치 형태의 지능구조물을 제작한 후 실험적으로 얻은 동탄성 특성값과 모델에 의해 예측된 동탄성 특성값을 비교 고찰하여 제시된 동적 모델에 대한 타당성을 입증하였다. 또한 모델을 통해 전장부하 함수로 예측된 주파수 응답곡선 중에서 각 주파수 대역에 대해 최소 변위가 되는 응답곡선을 요구응답으로 설정한 후, 그에 해당하는 전장부하를 선정하는 논리적인 능동 진동제어 알고리즘을 제안하였다. 제어알고리즘의 유용성을 입증하기 위해 실험적으로 수행된 능동 진동제어 결과를 주파수영역과 시간영역에서 제시하였다.

• The Korean Journal of Rheology
• /
• v.7 no.2
• /
• pp.120-127
• /
• 1995

중량비가 측쇄의 함량이 각각 4.37%(시료I)와 8.97%(시료II)인 두종류의 사과 펙틴을 이용하여 측쇄가 펙틴용액의 점탄성에 미치는 역할에 대하여 연구하였다. 시료II가 시료 I보 다 동일한 농도에서 더높은 전단속도에서는 오히려 시료 I의 전단점도가 시료 II보다 높은 값을 보였다. 시료I과 시료 II의 η0는 농도에 대하여 각각 η0 C4.23의 관계를보여 시료II가 더높은 농도의존성을 보였다. 한편 용액의 탄성특성을 나타내는 저장탄성계수(G＇)와 zero-shear recoverable compliance(Jeo)의 경우에는 시료II가 시료I보다 높은 값을 보였는데 이는 측쇄가 탄성과 밀접한 관계가 있다는 것을 의미한다. 펙틴용액의 전단점도와 복소점도 를 비교했을 때 거의 비슷한 값을 보였으나 예외적으로 고측쇄의 시료 II의 경우 고농도에 서 서로 상이한 값을 보였다. 본연구의 결과는 진한 용액하에서 측쇄가 분자간의 상호엉킴 에 상당한 기여를 하고 있음을 나타내었다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.411-414
• /
• 2006

In this paper, the forced vibration of damped composite beam with arbitrary section was analyzed. The damping material was assumed to have either complex shear modulus or complex Young???smodulus. Damped composite beam could be modeled using beam elements with less D.O.F. rather than solid elements. Finite element method for these methods was formulated and programmed using complex values. The results of frequency responses revealed good agreement with those of NASTRAN in several beam structures.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.978-981
• /
• 2005

The vibration analysis of damped sandwich beam is conducted using finite element method. The equation of motion presented by Mead and Markus is used to formulate FEM. Also as the thickness of the core in the damped sandwich beam goes to zero, conventional beam theory based on the transformed-section method and the equation of Mead and Markus are compared. According to the change of thickness and loss factor of the core, the forced frequency response of beam is calculated and discussed. And then using the half-power band width method, the damping ratio of each mode is calculated and discussed about each case.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1530-1537
• /
• 1991

본 연구에서는 반무한 직선 계면균열의 상하면에 임의로 분포하는 어떠한 하 중에 대해서도 그 해석이 가능한 그린함수(Green's function)를 구하고자 한다. 이 를 위하여 반무한 직선 계면균열상의 임의의 한 점에 평면 집중하중이 작용하는 문제 와 비평면 집중전단하중이 작용하는 문제를 각각 택하였고, 이때 계면균열의 선단은 열려있다고 가정하였다. 이 문제를 풀므로써 균열선단부근의 응력성분을 결정하고 이로부터 그린함수의 의미를 지니는 응력강도계수에 대한 폐형해를 얻었다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.210-215
• /
• 2002

MR(Magnetorheogical) fluid composed of fine iron powders dispersed in silicon oil is utilized to many smart structures and devices because of its significant rheological property change by the application of an external magnetic field. When we deal with the shock wave attenuation of warship structures, we should be able to characterize the high frequency behavior of MR fluids. So far, however, many efforts have been focused on the material characterization of MR fluids at low frequencies below 100Hz. In this paper, the MR fluid property characterization at high frequency region is performed. An experimental setup based on wave transmission technique is made and the storage modulus as well as the loss modulus of MR fluids are found from the measured data of speed sound and attenuation. Details of the experiment are addressed and the obtained storage and loss moduli are addressed at $50kHz{\sim}100kHz$.