• Journal of the Korea Concrete Institute
• /
• v.19 no.2
• /
• pp.241-250
• /
• 2007

In case of retrofitting a concrete structure subjected to blast load by using retrofit materials such as FRP (fiber-reinforced polymer), appropriate ductility as well as raising stiffness must be obtained. But the previous approximate and simplified models, which have been generally used in the design and analysis of structures subjected to blast load, cannot accurately consider effects on retrofit materials. Problems on the accuracy and reliability of analysis results have also been pointed out. In addition, as the response of concrete and reinforcement on dynamic load is different from that on static load, it is not appropriate to use material properties defined in the previous static or quasi-static conditions to in calculating the response on the blast load. In this study, therefore, an accurate HFPB (high fidelity physics based) finite element analysis technique, which includes material models considering strength increase, and strain rate effect on blast load with very fast loading velocity, has been suggested using LS-DYNA, an explicit analysis program. Through the suggested analysis technique, the behavior on the blast load of retrofitted concrete walls using CFRP (carbon fiber-reinforced polymer) and GFRP (glass fiber-reinforced polymer) have been analyzed, and the retrofit capacity analysis has also been carried out by comparing with the analysis results of a wall without retrofit. As a result of the analysis, the retrofit capacity showing an approximate $26{\sim}28%$ reduction of maximum deflection, according to the retrofit, was confirmed, and it is judged ate suggested analysis technique can be effectively applicable in evaluating effectiveness of retrofit materials and techniques.

• Composites Research
• /
• v.13 no.6
• /
• pp.9-22
• /
• 2000

The Rayleigh-Ritz procedure based on energy method is used to present analytically the natural frequencies and the critical buckling loads for four types of loading conditions: (1) uniaxial, (2) biaxial, (3) positive shear and (4) negative shear, of the rectangular, composite plates unidirectionally stiffened with box beam type stiffeners. In analysis the discrete stiffener theory is adopted to present the effect of stiffeners in the plate structure. The convergence study is presented to demonstrate the accuracy of the results. Contour plots of the vibrated and buckled mode shapes are shown for some examples. The effect of various parameters such as numbers, position, aspect ratio of stiffener and layer angle, aspect ratio of plate are focused.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.04a
• /
• pp.28-28
• /
• 1999

본 연구는 이전 연구에서 500KW급 중형 수평축 발전기를 설계하였던 경험을 토대로 750KW급 대형 수평축 풍력발전용 복합재 회전날개를 개발하기 위해 수행되었다. 회전날개의 대형화에 따른 구조강도 확보 및 경량화 문제를 해결하기 위해 날개의 단면구조를 변경하였고, 주 하중을 받는 스파부분을 보강하였으며, 취급이 어렵고 가격이 비싼 노맥스 허니컴 대신에 폼을 사용한 샌드위치 구조를 적용하였다. 또한 경량화를 위해 금속재 플렌지형 허브부분 접합방식을 삽입볼트 접합방식으로 구조 설계를 변경하였다. 이러한 복합재 회전날개의 구조적 안정성을 확인하기 위해 상용 유한요소 해석 코드인 NISA II를 사용하였으며, 선형정적해석, 고유진동수해석, 국부 좌굴해석 등을 수행하여, 무게의 증가는 최대한 억제하면서 대형화에 따른 구조강도의 확보가 이루어졌음을 확인하였고, 피로수명해석을 통하여 20년 이상의 요구 수명을 만족함을 확인하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.12
• /
• pp.967-974
• /
• 2013

Recently the authors had proposed the z-pinning patch concept to simply manufacture z-pinned composite structures at industrial production site and manufactured composite single-lap shear joint specimens using the concept. Through static tensile test on the specimens they had obtained 54~68% improvement of the joint strength. As a sequential study of it, in this study, fatigue test has performed to measure an improvement of joint strength under cyclic loading. The z-pin's material is stainless steel and its surface was specially machined into zagged shapes and chemically corroded to increase the connection force with composite materials. Approximately 98~125% improvement of the joint strength under cyclic loading was obtained.

• The magazine of the Korean Society for Advanced Composite Structures
• /
• v.6 no.1
• /
• pp.37-42
• /
• 2015

• Composites Research
• /
• v.17 no.5
• /
• pp.39-46
• /
• 2004

In this study, the strength of spatially reinforced composites (SRC) are predicted by using stiffness reduction for each structural element composed of a rod stiffness in each direction and a matrix stiffness proportional to its rod volume fraction. Maximum failure strain criteria is applied to rod failure, and modified Tsai-Wu failure criteria to matrix failure. The material properties composed of the tensile failure strain of a rod, the compressive failure strain of 3D SRC, the tensile and compressive strength of the 3D SRC in the $45^{\cir}$ rotated direction from a rod and the shear strength of the 3D SRC are measured to predict the SRC strength. The strength distributions of the 3D/4D SRC in rod and off-rod direction have the largest and the smallest values, respectively. A variable load step is selected to increase an efficiency of strength distribution calculation. Uniform load step is applied when a load history is needed. The results of compressive strength from analysis and experiment show the 18 % difference though the initial slop is coincident with each other.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.1
• /
• pp.147-156
• /
• 2004

The Rehabilitation and repair of structurally deteriorated, reinforced concrete structures will be highly demanded in the near future. The purpose of this study is to investigate whether damaged beams that crack and deflection are developed by bending moment are restored to the former state. In conclusion, when specimens strengthened with Steel Plate, CFS(Carbon Fiber Sheet) and CFRP-Grid(Carbon Fiber Reinforced Plastic-Grid) are compared with standard specimen, flexural capacity is increased and ductility and energy absorbtion capacity are similar with undamaged specimen. Therefore Steel Plate, CFS(Carbon Fiber Sheet) and CFRP-Grid (Carbon Fiber Reinforced Plastic-Grid) have highly efficiency as material of flexural strengthening.

• Composites Research
• /
• v.12 no.5
• /
• pp.54-64
• /
• 1999

This study investigated the impact behaviors of the stitched sandwich composites under the low energy impact by the use of drop weight impact tester. These sandwich composites condidted of the glass fabric faces with a urethane foam core. The upper face and the lower face were stitched to combinr through the core thickness direction using the polyester reinforcements. Four types of the stitched sandwich composites, each having a different core thickness, were tested to determine the effects of the core thickness. The impact conditions were changes with the variations of the mass and drop height of the impact tup. The test results showed that the core thickness and the impact condidtions such as the drop height and the mass of the impact tup affected the impact force, the contact time, and the strain behaviors of the stitched sandwich composites. The stitched sandwich composites are able to avert the damage and also maintain the structural integrity even thouth the presence of the damage owing to the through-the-thickness reinforcements. However, it is important to improve the wetting ability of the stitched reinforcements so that the conventional structures are substituted for the stitched sandwich composites effectively.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.3
• /
• pp.53-59
• /
• 2018

This study analyzed the field applicability through the combination of environment-friendly grid-typed reinforcements and pre-mixed fiber with filler. The film of the grid-typed reinforcement is made by recycled PE resin. And, Ascon fiber is obtained the dispersion by pre-mixing of filler. To be able to recognize in advance the various circumstances that could arise in the construction of the road pavement layer, we conducted a basic field application test of the (Mock Up) pavement layer. As a result, it was found that the pavement with environment-friendly grid-typed reinforcement and dispersive fiber construction had improved strength, stress, and rutting resistance. It is consistent with the strength and stress results of the actual test of the mock up specimen. It is expected to perform an effective role in the safety as well as the use of environment-friendly fibers in actual construction.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.3 no.2
• /
• pp.199-204
• /
• 1999

A recent application of advanced composite materials, primarily fiber-reinforced plastic (FRP) composites, in structures is the reinforcement of conventional structural materials, such as concrete and glued-laminated timber (glulam), to increase their performance. In particular, the construction of large-scale glulam structures usually requires members with large depths and to significantly increase the stiffness and strength of glulam, the members can be reinforced with FRP at top and bottom surfaces. In this paper, glulam beams reinforced with GFRP strip are tested under 2-point bending and results are compared with numerical solution using layer-wise beam theory.