• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.7
• /
• pp.1341-1350
• /
• 1992

This paper addresses the practical problem of finding a useful strain energy function of the incompressible rubberlike materials. It examines methods by which the form of the functions are determined and shows how the selection of experimental data influences the resulting form of the functions. From this information, an optimal choice of the form of energy functions becomes possible. Phenomenological theories used in this paper are limited to elastic, incompressible material models. Due to the nature of the phenomenological methods, these theories are accurate only for the materials treated. However, they serve as a starting basis for the study of more complicated material behaviors.

• Korean Journal of Agricultural Science
• /
• v.13 no.1
• /
• pp.113-122
• /
• 1986

In order to promote mechanization of corn harvesting in Korea, this study was conducted to find out the effect of moisture content on compressive properties such as force, deformation, energy and modulus of stiffness to the bioyield and the rupture point for Korean corn kernel. In this study, the loading positions of corn were flat, edge, longitude and the moisture contents were about 13, 17, 21, 25% in wet basis. The compression test was carreied out with flat plate by use of dynamic straingage for three varieties of Korean corn under quasi-static force when the loading rate was 1.125mm/min. The results of this study are summarized as follows; 1. When the moisture content of corn ranged from 12.5 to 24.5 percent, at flat position, the bioyied force was in the range of 13.63-26.73 kg and the maximum compressive strength was in the range of 21.55-47.65kg. Their values were reached minimum at about 17% and maximum at about 21% moisture content. The bioyield force was in the range of 13.58-6.70kg at edge position and the maximum compressive strength which was 16.42 to 7.82kg at edge position was lower than that which was 18.55-9.05kg at longitudinal position. 2. Deformation of corn varied from 0.43 to 1.37 mm at bioyield point and from 0.70 to 2.66mm at rupture point between 12.5 to 24.5% moisture content. As the moisture content increased, deformation was increased. 3. The moduli of resilience and toughness of corn ranged from 2.60 to 8.57kg. mm and from 6.41 to 34.36kg. mm when the moisture content ranged from 12.5 to 24.5 percent, respectively. As the moisture content increased, the modulus of toughness was increased at edge position and decreased at longitudinal position. And their values were equal each other at 22-23% moisture content. 4. The modulus of stiffness was decreased with increase in the moisture content. Its values ranged from 32.07 to 5.86 kg/mm at edge position and from 42.12 to 18.68kg/mm at flat position, respectively. Also, the values of Suweon 19 were higher than those of Buyeo. 5. It was considered that the compressive properties of corn at flat position were more important on the design data for corn harvesting and processing machinery than those of edge or longitudinal position. Also, grinding energy would be minimized when a corn was processed between about 12.5 to 17% moisture content and corn damage would be reduced when a corn was handled between about 19 to 24% moisture content in wet basis.

• Nuclear Engineering and Technology
• /
• v.3 no.1
• /
• pp.21-31
• /
• 1971

The part of the work of plastic deformation of metal goes into the changes in the total surface free energy. This contribution is dependent on the specific surface free energy, which is affected by the environment. Based on thermodynamical approach, volume constancy requirement and adsorption induced two distinct dislocation interaction mechanisms for strengthening or weakening of metals at surface, theoretical derivation has been made to show that the environmental contribution on the strain hardening, the stress and the energy required for plastic deformation can be expressed in terms of solid surface tension in vacuum (${\gamma}$$_{s}$), interfacial tension (${\gamma}$$_{se}$ ), surface dislocation density ($\rho$$_{s}$), internal dislocation density ($\rho$$_{i}$) and fraction of surface site uncoverage (f). On the basis of theoretical derivation, the various mechanical behaviours under different environments are predicted.d.d.

• Journal of Korean Society of Steel Construction
• /
• v.8 no.4 s.29
• /
• pp.51-58
• /
• 1996

연직하중을 받는 적층보에서 박리좌굴하중을 산정하는 방법을 제시하였다. 재료역학적 방법에 근거하여 박리된 보의 변위함수를 설정하였으며 힘과 변위의 적합조건을 이용하여 연직하중과 박리좌굴하중과의 관계식을 유도하였다. 또한 박리의 진전을 판단하기 위한 변형도에너지 방출율(release rate)을 산정하였다. FRP로 보강된 GLULAM보에 대한 실험과 비교한 이론해는 정확한 결과를 보여 주었으며 연직하중을 받는 적층보의 박리 진전현상은 축하중을 받는 보와는 다른 거동을 보였다.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.309-314
• /
• 2000

Rubber is used as a primary suspension component in a vehicle or a mechanical structure. The aim of this study is to establish a procedure for measuring the material properties of rubber and to analyze the differences of material properties of virgin rubber and heat aged rubber. The effect of mechanical conditioning was shown and included in the procedures of tensile. compression. simple shear. and pure shear tests. In addition. using engine oil was recommended for compression test in order not to have barrelling. Moreover, based on the material properties of vil·gin rubber and heat aged rubber. equations of C10 and IRHD were proposed as a function of heat aging temperature and time.

• Nuclear Engineering and Technology
• /
• v.20 no.4
• /
• pp.241-245
• /
• 1988

It is very important to investigate the behaviors of the material parameters governing PCI fuel failure during power ramp because PCI fuel failure is considered to be related to the operations limits of power reactors. In this study, the behavior characteristics of the material parameters such as hoop stress, hoop strain, ridge height, creep strain rate and strain energy in cladding were studied as a function of the operating parameters such as power shock and ramp rate. The FEMAXI-IV fuel rod performance analysis code was used for this study.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.3
• /
• pp.199-205
• /
• 2012

In this study, wave transformation by damping due to the permeable bed of finite depth is investigated. The relationship between wave damping rate and relative water depth are presented. The damping rate is used in the eigenfunction expansion method to calculate the wave dissipation over the permeable bed. For a permeable shoal, the eigenfunction expansion model result is compared with that of the integral equation method to show good agreement. The model is also used to examine the wave reflection over the permeable planar slope of various frequency. It has been found that in general relatively short waves are more influenced by the permeability of the permeable seabed than relatively long waves unless the water depth is so large that the influence of permeable bed on surface water waves disappears.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.2
• /
• pp.97-104
• /
• 2005

A simple but efficient grid generation technique by using the modified compressible form of stream function has been formulated. Transformation of a physical plane to a streamline plane, the Von Mises Transformation, has been widely used to solve the differential equations governing flow phenomena, however, limitation arises in low velocity region of boundary layer, mixing layer and wake region where the relatively large grid spacing is inevitable. Modified Von Mises Transformation with simple mathematical adjustment for the stream function is suggested and applied to solve the confined coaxial turbulent jet mixing with simple $\kappa-\epsilon$ turbulence model. Comparison with several experimental data of axial mean velocity, turbulent kinetic energy, and Reynolds shear stress distribution shows quite good agreement in the mixing layer except in the centerline where the turbulent kinetic energy distributions were somewhat under estimated. This formulation is strongly suggested to be utilized specially for free turbulent mixing layers in axisymmetric flow conditions such as the investigation of mixing behavior, jet noise production and reduction for Turbofan engines.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.4B
• /
• pp.377-384
• /
• 2009

In order to reduce computing time significantly for a large matrix in EFEM of linear waves propagation over ripple beds, each of which is approximated to a multi-step topography, a partition method is presented to calculate reflection coefficients. By use of 10 evanescent modes in the model, the most accurate numerical solutions have been obtained up to date, which show different behaviors of computed reflection coefficient in some cases against the existing results. Both computing time and memory of the present partition model for solving a large matrix are still so much demanding that it is needed to develop an efficient method.

• Journal of Biosystems Engineering
• /
• v.20 no.2
• /
• pp.141-150
• /
• 1995

땅콩을 대상으로 하는 각종 농산가공기계의 개발 및 최적 작동에 필요한 땅콩 자실의 물리적, 기계적 및 공기 역학적 성질에 대한 연구가 수행되었다. 영호, 올, P.I. 314817의 3 가지 품종에 대해 땅콩 자실의 형상, 각부 칫수, 진밀도, 산물밀도 및 종실율이 측정되었으며, 땅콩자실에 대해 압축실험을 실시함으로써 자실이 파괴될 때의 힘, 변형량, 그리고 단위 체적당 최대 흡수 에너지인 터프니스 계수를 측정하여 기계적 성질로서 제시하였다. 공기 역학적 성질로서는 땅콩 자실과 종실의 종말속도 및 항력계수가 측정되었다. 1. 땅콩 자실의 기하학적 형상은 수원체로 모형화할 수 있었다. 2. 진밀도는 땅콩 자실의 경우는 515-620 $kg/m^3$, 종실의 경우는 960-1,090 $kg/m^3$, 의 값을 보였다. 3. 대합면이 수평인 자세에서의 파괴력은 영호가 61.9 N, P.I. 314817은 71.5 N, 올 땅콩은 84.8 N였으며, 터프니스 계수는 각각 30, 43, 72 kN-$m/m^3$, 의 값을 보였다. 모든 품종과 함수율에서 파괴력과 터프니스 계수는 대합면이 수직인 자세에서보다 수평자세에서 더 큰 값들을 보였다. 4. 땅콩 자실과 종실의 평균 종말속도는 각각 8.7-9.9 m/s, 10.0-11.6 m/s 범위였다. 종말속도는 진밀도와 직선적인 관계가 있었으며 품종과 형상에 따른 뚜렷한 종말속도의 차이는 보이지 않았다.