• Journal of the KSME
• /
• v.31 no.4
• /
• pp.356-363
• /
• 1991

선형 탄성 유한요소 응력해석과 평균응력 효과를 고려한 저주기 피로실험으로부터 결정된 피로 특성, 그리고 국부변형률 방법을 종합하여 외경에 흠이 존재하는 자긴가공된 두꺼운 압력 용기의 피로수명이 평가되었다. 직사각형의 매우 날카로운 흠에서의 응력집중계수는 타원형 홈에서의 응력집중계수의 약 두배의 값이 얻어졌으며, 고강도 압력용기강인 ASTM A723의 저주기 피 로거동에 대한 평균응력 영향은 Morrow 및 SWT 파라메타를 이용하여 충분히 고려되었다. 균열발생이 예상되는 위험한 부분인 홈의 뿌리부분에서의 국부적인 응력, 변형률이 계산되었으며 예측된 피로수명은 실험적으로 얻어진 수명과 비교했을 때 2에서 4배의 오차를 보이면서 일치 하는 결과를 얻었다.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.5
• /
• pp.115-125
• /
• 1997

콘크리트의 변형률국소화는 콘크리트의연화거동에 수반되어 변형이 국부적으로 집중되는 현상이다. 본 연구의 목적은 인장과 압축하중상태에서 콘크리트 부재에 발생하는 콘크리트 변형률 국소화 거동을 해석적으로 재현할 수 있는 통일된 모형을 제안하는 것이다. 본 논문에서는 인장과 압축에 대하여 변형률국소화가 일어나는 콘크리트 부재를 변형률 연화가 일어나는 국소화영역과 탄성제하가 발생하는 비국소화영역으로 구분하여 모델링하는 통일된 모형을 제안하였다. 또한 제안된 모형에서 미시역학적 평균화기법을 이용해 평균등가탄성계수와 수정된 평균등가탄성계수를 구하여 시편의 크기와 국소화영역의 크기에 따는 해석을 수행하였으며 기존의 실험값과 비교하였다. 연구결과, 본 연구에서의 변형률국소화모형이 크기효과를 포함한 콘크리트의 변형률국소화거동 해석에 타당하게 적용될 수 있음을 보여주었다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.12 no.4
• /
• pp.295-306
• /
• 2010

Contrary to an intact rock, the jointed rock mass shows strain-dependent deformation characteristics (elastic modulus and damping ratio). The maximum elastic modulus of a rock mass can be obtained from an elastic wave-based exploration in a small strain level and applied to seismic analyses. However, the assessment and application of the non-linear characteristics of rock masses in a small to medium strain level ($10^{-4}{\sim}0.5%$) have not been carried out yet. A non-linear dynamic analysis module is newly developed for FLAC3D to simulate strain-dependent shear modulus degradation and damping ratio amplification characteristics. The developed module is verified by analyzing the change of the Ricker wave propagation. Strain-dependent non-linear characteristics are obtained from disks of cored samples using a rock mass dynamic testing apparatus which can evaluate wave propagation characteristics in a jointed rock column. Using the experimental results and the developed non-linear dynamic module, seismic analyses are performed for the intersection of a shaft and an inclined tunnel. The numerical results show that vertical and horizontal displacements of non-linear analyses are larger than those of linear analyses. Also, non-linear analyses induce bigger bending compressive stresses acting on the lining. The bending compressive stress concentrates at the intersection part. The fundamental understanding of a strain-dependent jointed rock mass behavior is achieved in this study and the analytical procedure suggested can be effectively applied to field designs and analyses.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.5
• /
• pp.133-141
• /
• 2002

Isotropic rock and anisotropic rock have different tensile strength which has the greatest influence on rock failure. In this study, elastic modulus of anisotropic rock is obtained through uniaxial compression test, and tensile strength and tension failure behavior are analyzed through indirect tensile strength test. Stress concentration factor of a specimen at the center is obtained from anisotropic elastic modulus and strain by indirect tensile strength test. Theoretical solutions for tensile strength of isotropic and anisotropic rock are compared. Stress concentration factor of anisotropic rock is either higher or lower than isotropic rock depending on the inclination angle of bedding plane. The use of stress concentration factor of isotropic rock resulted in overestimation or underestimation of tensile strength.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.1
• /
• pp.46-51
• /
• 2002

Fatigue life estimation by the theoretical stress concentration factors are, in general, considerably different from test results. And in calculating stress concentration factor, it is very difficult to consider actual geometry and material property which are the notch shapes, imperfections or defects of materials such as porosities inclusions and casting defects, etc. Therefore, the paper deals with the experimental method to find out the more exact stress concentration factors by measuring the strain distributions on each specimen by 3D-ESPI(Electronic Speckle Pattern Interferometry) System. Then the fatigue lives are compared between theoretical calculations using stress concentration factors determined by 3D-ESPI system and fatigue test results.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.5
• /
• pp.329-335
• /
• 2006

It is necessary to study on the stress concentration experimentally, which is the main reason to avoid mechanical dilapidation and failure, when designing a mechanical structure. Stress concentration factor of a specimen of cantilever beam with a circular hole in the center was measured using both strain gage and photoelastic methods in this paper. In strain-gage measurement, three strain gages along the line near a hole of the specimen were installed and maximum strain was extrapolated from three measurements. In photoelastic measurement, two methods were employed. First, the Babinet-Soleil compensation method was used to measure the maximum strain. Secondly, photoelastic 4-step phase shilling method was applied to observe the strain distribution around the hole. Measurements obtained by different experiments were comparable within the range of experimental error.

• Journal of the Korea Convergence Society
• /
• v.5 no.1
• /
• pp.23-27
• /
• 2014

In case eccentric load is applied at compact tension specimen, the propagation behavior due to existence or nonexistence of hole, numbers and positions of holes near crack is investigated in this study. Strain energy, displacement and stress happened in specimen are examined through simulation analysis. And stress intensity factor is obtained by the basis of strain energy and deformation. When defect or hole exists in structure, the possibility of fracture can be thought to be verified by using the study result.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1991.04a
• /
• pp.133-138
• /
• 1991

일반적으로 고무를 비롯한 점탄성재료는 형상 및 크기를 적절히 조절함으로 써 한 방향 이상으로의 원하는 스프링상수를 얻을 수 있으며, 금속에 비하여 내부 마찰에 의한 에너지 발산이 매우 크기 때문에 강제 진동시의 진폭저감 및 충격에 따른 자유진동의 감쇠에 널리 이용되고 있다. 이와 같은 진동감쇠 에 점탄성재료를 효과적으로 사용하기 위해서는 복소탄성계수 즉, 탄성계수 와 손실계수를 정확하게 알아내는 것이 필요하다. 점탄성재료의 복소탄성계 수는 주파수, 온도 및 변형률등에 따라 변하므로 이와 같은 사용조건의 함수 로 구해야 한다. 복소탄성계수를 실험적으로 구하는 방법은 여러가지가 있으 며 실험의 용이성과 관심대상에 따라 적절한 방법을 선택하게 된다. 본 연구 에서는 주파수변화에 따른 복소탄성계수를 임피던스법으로 집중질량 모형을 이용하여 구하려고 할 때, 실험데이타로부터 보다 정확한 결과를 얻기 위하 여 적절한 시편의 크기를 결정하는 방법을 제시하고자 한다. 이를 위해서 시 편내의 파동전달효과와 포아송비와 관련된 양단제한효과 그리고 정하중시 압축변형에 대한 시편의 좌굴등을 고려하여 이론적으로 해석하였으며 실험 적으로도 검증하였다.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.2 s.146
• /
• pp.213-219
• /
• 2006

Low cycle fatigue cracks are mainly detected at discontinuous welded locations with high stresses under repeated cyclic static loads due to cargo leading and unloading. Theoretical and analytical methods have been used for evaluation of local stress and strain which have an effect on a prediction of fatigue life, but those have difficulties of considering stress concentration at notched location and complicated material behavior of welded joint or heat affected zone. Electronic speckle pattern interferometry(ESPI) system is nondestructive and non-contact measurement system which can get the relatively accurate full field strain at critical positions such as welded zone and structural discontinuous location. In this study, local strain was measured on welded cruciform joint by ESPI system and then low cycle fatigue test was performed. Effect of local strain on low cycle fatigue life was examined by measured values using ESPI system. Moreover, experimental fatigue life was compared with established S-N curves using theoretical local strain and stress calculated by Neuber's rule.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.9
• /
• pp.859-869
• /
• 2015

In this study, we analyze the problem of wedge cracks, which are geometrically unsymmetrical in transversely piezoelectric materials. A single concentrated antiplane mechanical load and inplane electrical load are applied at the point of the wedge surface, while one concentrated antiplane load is applied at the crack surface. The crack surfaces are considered as permeable thin slits, where both the normal component of electric displacement and the electric potential are assumed to be continuous across these slits. Using Mellin transform method, the problem is formulated and the Wiener-Hopf equation is derived. By solving the equation, the solution is obtained in a closed form. The intensity factors of the stress and the electric displacement are obtained for any crack length as well as inclined and wedge angles. Based on the results, the intensity factors are independent of the applied electric loads. The electric displacement intensity factor is always dependent on that of stress intensity factor, while the electric field intensity factor is zero. In addition, the energy release rate is computed. These solutions can be used as fundamental solutions which can be superposed to arbitrary electromechanical loadings.