• Journal of IKEEE
• /
• v.15 no.4
• /
• pp.324-329
• /
• 2011

In recent years, the performance and functions of portable devices has increased. so it requires more power efficiency and energy density while using the battery for a long time. therefore Battery pack which are made up from several battery cells in series in order to achieve higher operating voltage is being used. when using a Li-ion battery, we need a protection circuit to protect from overcharge, over discharge, high temperature and over current. Also, when using battery pack, we need to Cell voltage balancing circuit that each cell in tune with the balancing. In this paper, the proposed IC is applicable by mobile devices as well as E-bike, hybrid vehicles, electric vehicles, and is expected to contribute to the development of domestic PMIC.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.527-535
• /
• 2017

Heat management is one of the most critical issues in Polymer Electrolyte Membrane Fuel Cells (PEMFCs) installed inside the fuel cell power pack of a fuel cell battery hybrid UPS. If the heat generated by the chemical reaction in the fuel cell is not rapidly removed, the durability and performance of the fuel cell may be affected, which may shorten its lifetime. Therefore, the objective of this study is to select and propose a proper cooling method for the fuel cells used in the fuel cell power pack of a UPS. In order to find the most appropriate cooling method, the various design factors affecting the cooling performance were studied. The numerical analysis was performed by a commercial program, i.e., COMSOL Multiphysics. Firstly, the surface temperature of the 1 kW class fuel cell stack with the cooling fans placed at the top was compared with the one with the cooling fans placed at the bottom. Various rotation speeds of the cooling fan, viz. 2,500, 3,000, 3,500, and 4,000 RPM, were tested to determine the proper cooling fan speed. In addition, the influence of the inhaled air flow rate was investigated by changing the porous area of the grille, which is the entrance of the air flowing from the outside to the inside of the power pack. As a result, it was found that for the operating conditions of the 1 kW class PEMFC to be acceptable, the cooling fan was required to have a minimum rotating speed of 3500 RPM to maintain the fuel cell surface temperature within an acceptable range. The results of this study can be effectively applied to the development of thermal management technology for the fuel cells inside the fuel cell power pack of a UPS.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.2
• /
• pp.33-42
• /
• 2023

Throughout all industries, eco-friendliness is being promoted worldwide with focus on suppressing the environmental impact. With recent international environment policies and regulations supported by government, the electric vehicles demand is expected to increase rapidly. Battery system itself perform an essential role in EVs technology that is arranged in cells, modules, and packs, and each of them are connected mechanically and electrically. A multifaceted approach is necessary for battery pack bonding technologies. In this paper, pros and cons of applicable bonding technologies, such as resistance welding, laser and ultrasonic bonding used in constructing electric vehicle battery packs were compared. Each bonding technique has different advantages and limitations. Therefore, several criteria must be considered when determining which bonding technology is suitable for a battery cell. In particular, the shape and production scale of battery cells are seen as important factors in selecting a bonding method. While dealing with the types and components of battery cells, package bonding technologies and general issues, we will review suitable bonding technologies and suggest future directions.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.6
• /
• pp.818-824
• /
• 2018

CFRP is often used as lightweight hull material for luxury yachts or special-service ships. An electric propulsion system is also eco-friendly, and has been trialled to equip a small vessel as its main propulsion. In this study, replacing the hull materials and propulsion system with CFRP and electric motors, we made an estimate of the effect of weight reduction and compared it to the original design, for this purpose a case study was conducted on a 45-ft yacht. When redesigning structures with CFRP, we applied the reinforcement content of the carbon fiber in the same way as the original (GC = 0.4), and when changing to the electric propulsion system, we designed motors and battery packs to achieve the same performance as the original. The result showed that CFRP and the electric propulsion system could make the structural and machinery weights 45 % and 58 % lighter, respectively. However, in terms of efficiency, it was confirmed that the electric propulsion system is practically inefficient because it requires a huge amount of battery packs for the same navigation range with diesel engines.

• Journal of the Korea Society for Simulation
• /
• v.32 no.4
• /
• pp.77-84
• /
• 2023

In the agricultural sector, power sources are being developed that use alternative energy sources such as electric tractors and hydrogen tractors, away from internal combustion engine tractors. As parts such as engines and transmissions used in conventional internal combustion engine tractors are replaced with motors and batteries, the center of gravity changes, and thus the risk of rollover should be considered. The purpose of this study is to analyze the overturn angle of the main parts of the electric tractor through dynamic simulation to minimize the overturn accident and to derive the optimal arrangement of parts to improve stability. A total of nine dynamics simulations were conducted by designing three components of the PTO motor, drive motor and the battery pack, and three factors of the arrangement method. As a result of the experiment, it was confirmed that Type3 Level3, in which the drive motor and the PTO motor are located at the front and rear of the tractor, and two battery packs are located in the middle of the tractor, has a high rollover angle. As a result of this study, the stability increased as the center of gravity was placed backward and located below. Future research needs to be done to find the optimal location of parts considering their performance and placement efficiency.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.16-21
• /
• 2017

In this paper, the effect of battery-package shape of electric vehicle on the forced convection around a group of battery cells has been numerically investigated. Simulations for the two package shapes with straight/curved ducts have been conducted to examine the two design factors; the maximum temperature and the temperature deviation of a group of cells which influence the cell durability. The simulation of the conjugate heat transfer has been simplified by employing an equivalent thermal conductivity of cell that consists of various materials. It has been found that the maximum temperature and the temperature deviation of curved duct were lower than those of straight duct. Velocity fields have also been examined to describe the temperature distribution of a group of cells and the position of maximum temperature was found to be related to the dead zone of flow field.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.3
• /
• pp.1-9
• /
• 2022

The aircraft targeted in this study is a vertical take-off and landing aircraft with 4 to 5 passengers, and the propulsion system for the aircraft is a distributed hybrid propulsion system that uses a gas turbine engine and a battery pack as the main power source to supply the power required by multiple motors. In this study, a design/analysis platform for a hybrid propulsion system was developed using the MATLAB/Simulink program based on the preliminary design results. Through simulation analysis, the output characteristics and operating range of each power source according to the mission profile were confirmed, and through this, the feasibility of the preliminary design result was confirmed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.138.1-138.1
• /
• 2010

직접메탄올 연료전지는 액체 메탄올 저장의 이점을 가지고 있어 이동형 전원 등의 응용에 적합하며, 최근 군사용 통신 전원이나 노트북용 전원으로 사용하기 위한 연구가 활발히 진행 중이다. 그러나 연료전지 스스로는 초기 기동을 할 수 없고 부하의 응답 특성에 빠르게 대응하기 어렵다. 따라서 연료전지와 배터리를 하이브리드로 구성하면 이러한 문제를 해결할 수 있을 뿐만 아니라 연료전지에 대한 부하가 안정되어 수명 연장에도 긍정적인 효과를 얻을 수 있다. 본 연구에서는 직접메탄올 연료전지와 리튬 이차전지를 연계하여 하이브리드 시스템을 구성하고자한다. 시뮬레이션을 통해 채널 형상에 따른 유동 및 차압을 해석하였으며, Single Cell, Short Stack 및 Stack의 특성을 평가하였다. 또한 하이브리드 시스템은 연료전지 스택, 연료전지 운전 장치, 리튬 이차전지, BMS, PCM, DC/DC Converter 등을 구성하여 시스템의 특성 등을 관찰하고자한다.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.171-172
• /
• 2016

본 논문에서는 군 주둔지의 전원공급을 위한 이동형 ESS 시스템에 대해서 제안한다. 제안하는 시스템은 군 주둔지와 같이 외부 소음 및 열에 민감한 시스템에서 디젤발전기를 대체하기 위하여 설계되었으며, 배터리 팩, BMS(Battery Management System), EMS(Energy Management System), PCS(Power Conditioning System), PMS(Power Management System), 구조물 그리고 차량체계로 구성된 시스템을 소개한다. 그리고 실험결과에서는 260kWh급의 이동형 ESS의 실차에 장착된 결과를 제시한다.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.397-398
• /
• 2016

This paper analyzes switching losses, efficiency and temperature depending on Si and SiC devices applied in two stage AC-DC converter. To evaluate the charge and discharge performance and stability of the battery pack, there is a need for a battery pack testing system. To do battery charge and discharge experiment used in battery pack test, A topology, two stage AC-DC converter, has been built. SiC devices more decrease switching losses than that of Si. Also, cooling system was applied in Si and SiC devices. When using SiC devices, it can be confirmed that the size of heat sink is reduced for small loss.