• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.10 no.3
• /
• pp.219-228
• /
• 2012

A long-term R&D program for HLW disposal technology development was launched in 1997 in Korea and Korea Reference disposal System(KRS) for spent fuels had been developed. After then, a recycling process for PWR spent fuels to get the reusable material such as uranium or TRU and to reduce the volume of radioactive waste, called Pyro-process, is being developed. This Pyro-process produces several kinds of wastes including metal waste and ceramic waste. In this study, the characteristics of the waste from Pyro-process and the concepts of a disposal container for the wastes were described. Based on these concepts, thermal analyses were carried out to determine a layout of the disposal area of the ceramic wastes which was classified as a high level waste and to develop the disposal system called A-KRS. The location of the final repository for A-KRS is not determined yet, thus to review the potential repository domains, the possible layout in the geological characteristics of KURT facility site was proposed. These results will be used in developing a repository system design and in performing the safety assessment.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.9
• /
• pp.887-893
• /
• 2010

Role of the perforated pipe is to drain the water with equal pressure and velocity through the holes of perforated pipe. The perforated pipe is being used in many processes of water treatment system, however, the design parameter of perforated pipe is not standardized in korea. In this study, we have found the design parameter of perforated pipe in the water treatment system using the Computational Fluid Dynamics (CFD). The uniformity of outflow from the perforated pipe is directly affected according to area ratio (gross area of holes/surface area of the perforated pipe). In other words, the uniformity of outflow is improved as area ratio is smaller. Also, at the same area ratio, the uniformity of outflow is improved as number of holes is increase. Specially, in case of the two holes per length of pipe diameter (2/D) shows the most uniformity of outflow and the best hydraulic with the smaller pressure drop. When the inlet velocity of pipe is about 0.06m/sec, the flux of pipe has decreased as from front to backward. When the inlet velocity is 3 m/s, the flux of pipe has increased as from front to backward.

• Journal of Korea Entertainment Industry Association
• /
• v.15 no.2
• /
• pp.203-212
• /
• 2021

The research purpose is analyzing the relationship between the distributive justice and turnover intention of the workers in community rehabilitation centers. This study also examines the mediating effect of job satisfaction between the distributive justice and the turnover intention. For this purpose, the survey was conducted to workers of 14 community rehabilitation centers in Daejeon and Chungnam area, and the 365 data were used for analysis. The results of analysing as follows: 1) the distributive justice of the workers in community rehabilitation centers effected the turnover intention negatively and the job satisfaction positively. In addition, the partial mediating effect of job satisfaction was proved between the distributive justice and the turnover intention. The analysis results show that the distributive justice is the important independent variable of the turnover intention and the job satisfaction is the important parameter between the two variables. According to these analysis results, several suggestions were made to reduce the turnover intention of the workers being engaged in community rehabilitation centers in terms of the improving their distributive justice and job satisfaction.

• Journal of Convergence for Information Technology
• /
• v.12 no.3
• /
• pp.132-140
• /
• 2022

This study was conducted to identify the optimal lotion manufacturing conditions with decursin and decursinol angelate of Angelica gigas Nakai extraction. Lotion was confirmed that it had viscosity (5,208±112 cPs), assay (99.71±1.01%), and pH (5.62) for 3 months. The optimization of manufacturing conditions of mixing 4 for lotion formulation were made by 22+3 full factorial design. Mixing temperature (40-80℃) and mixing time (10-30 min) were used as independent variables with three responses(assay, pH, and weight variation) as critical quality attributes (CQAs). The model for assay and weight variation identified a proper fit having a determination coefficient of the regression equation (about 0.9) and a p-value less than 0.05. Estimated conditions for the optimal manufacturing process of lotion were 61.93℃ in mixing temperature and 15.85 min in mixing time. Predicted values at the mixing temperature (60℃) and mixing time (20 min) were 100.69% of assay, 5.57 of pH, and 98.07% of weight variation. In the verification of the actual measurement the obtained values showed 100.29±0.98% of assay, 5.57±0.02 of pH, and 98.27±0.89% of weight variation, respectively, in good agreement with predicted values.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.3
• /
• pp.817-823
• /
• 2023

Manufacturing plants face the challenge of reducing energy use in response to climate change. Reducing energy consumption can be seen as one of the most important issues, such as reducing production costs and improving efficiency. Among manufacturing industries, the increase in energy consumption in the food industry is gradually increasing along with the improvement of the standard of living and the increase in population. In order to save energy in food processing plants, it is important to identify and analyze energy consumption characteristics in energy-consuming processes. Prior to this, it is necessary to monitor and analyze existing energy consumption to derive reduction measures. In this study, a small and medium-sized food processing plant producing processed meat products was used as a case study to identify and analyze the energy consumption structure at typical cycle/stage level of the batch heating process. From this, we tried to establish realistic and quantitative goals that can be obtained under individual process operating conditions. The results of this study will be used as basic data for the development of diffusion and pervasive energy saving FEMS technology for common core processes of food factories of small and medium-sized enterprises in the future.

• Korean Chemical Engineering Research
• /
• v.54 no.1
• /
• pp.44-51
• /
• 2016

The powder core, conventionally fabricated from iron particles coated with insulator, showed large eddy current loss under high frequency, because of small specific resistance. To overcome the eddy current loss, the increase in the specific resistance of powder cores was needed. In this study, copper oxide coating onto electrically conductive iron particles was performed using a planetary ball mill to increase the specific resistance. Coating factors were optimized by the Response surface methodology. The independent variables were the CuO mass fraction, mill revolution number, coating time, ball size, ball mass and sample mass. The response variable was the specific resistance. The optimization of six factors by the fractional factorial design indicated that CuO mass fraction, mill revolution number, and coating time were the key factors. The levels of these three factors were selected by the three-factors full factorial design and steepest ascent method. The steepest ascent method was used to approach the optimum range for maximum specific resistance. The Box-Behnken design was finally used to analyze the response surfaces of the screened factors for further optimization. The results of the Box-Behnken design showed that the CuO mass fraction and mill revolution number were the main factors affecting the efficiency of coating process. As the CuO mass fraction increased, the specific resistance increased. In contrast, the specific resistance increased with decreasing mill revolution number. The process optimization results revealed a high agreement between the experimental and the predicted data ($Adj-R^2=0.944$). The optimized CuO mass fraction, mill revolution number, and coating time were 0.4, 200 rpm, and 15 min, respectively. The measured value of the specific resistance of the coated pellet under the optimized conditions of the maximum specific resistance was $530k{\Omega}{\cdot}cm$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.6
• /
• pp.1754-1759
• /
• 2008

To produce plastic parts that have fine pattern through conventional injection molding, a lot of difficulties follow. Therefore, rapid heating and cooling methods are good candidates for manufacturing injection-molded parts with micro/nano patterns. In this study, we adopted the E-Mold patent technology. The mold for E-Mold technology has a separate heated core with micro heaters. It is very important to optimize the lay-out of the heaters in heated core because it influences both control and distribution of mold temperature. We developed a optimization method of heating line lay-out by using commercial softwares and compared the output with the experimental results. We used Pro-Engineer Wildfire 2.0 for the mold design, ICEMCFD for mesh generation, and FLUENT for heat transfer simulation. The simulation results showed the temperature profile from $60^{\circ}C$ to $120^{\circ}C$ or $180^{\circ}C$ during heating and cooling process which were compared with the injection molding experiments. We concluded that the simulation could well explain the experimental results. It was shown that the E-Mold optimization design for heater lay-out could be available through the simulation.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.264-267
• /
• 2005

수소의 소규모 분산 생산 기술은 본격적 인 수소 인프라가 도입되기 전에 연료전지 자동차의 수소 충 전용이나 분산 발전형 연료전지의 수소 공급을 위해 필요하다. 생산 용량은 수소 기준으로 $10\~100 Nm^3/hr$ 정도로 현재로선 천연가스의 수증기 개질법이 가장 경제적인 공정으로 알려져 있다. 소규모 생산에 따른 열효율 저하를 줄이 기 위해 단위 공정들이 통합된 컴팩트 개질 시스템의 개발이 필요하다. 핵심 기술인 컴팩트 리포머의 국산화 기술 확보를 위하여 $20 Nm^3/hr$용량의 동심관형 리포머를 설계, 제작하였다. 내부구조는 제작의 단순화를 고려하여 중첩된 동심관이 배열되었고 압력 손실과 열웅력 발생을 억제하도록 유로를 배치하였다. 수증기개질 반응에 필요한 반응열은 리포머 본체에 부착된 버너를 이용하여 공급하였다. 성능 측정을 위한 부속 기기로 상온 흡착식 탈황기, 폐열 회수형 수증기 발생기, 반응물 예열을 위한 열교환기, 생성 가스 응축기를 설계 제작하여 전체 리포밍 시스템을 구성하였다. 반응 온도 $680\~720^{\circ}C$, 탄소 대 수중기 비(S/C ratio) $2.7\~3.2$ 조건에서 수증기 개질 반응을 수행하였다. 해당 반응 조건에서 메탄 전환율 $89\%$ 이상, 저위 발열량 기준 개질 열효율 $70\%$ 이상을 달성하였고 개질 생성가스 내 수소의 최대 유량은 $23.4Nm^3/h$였다. 개발된 리포밍 시스템은 고순도 수소 생산이 필요한 경우, 수소 수율 향상을 위한 고온 수성 가스 전화 반응기를 통합 가능하도록 열교환기 구성을 조정할 수 있으며 용융 탄산염 연료전지와 같이 고온형 연료전지의 경우 $550^{\circ}C$ 이상으로 개질 생성 가스를 공급하도록 구성할 수도 있다. 향후 리포머 본체의 개질 효율 향상 및 장치 소형화, 부속 기기의 최적화를 통한 전체 리포밍 시스템 개선, 스케일 업 설계를 위한 엔지니어링 설계 패키지 구성을 계획하고 있다.

• Journal of Bio-Environment Control
• /
• v.13 no.2
• /
• pp.81-89
• /
• 2004

This study was conducted in a commercial plug glasshouse in Sacheon to examine the possibility of producing tomato plug seedlings using various growing media containing cellular glass foam (CGF)and carbonized chestnut woodchips (CCW) as medium components. Plug seedlings of 'Seogun' tomato were grown in media containing 50% CCW＋50% peatmoss, 33% CGF＋67% peatmoss, and 50% peatmoss＋50% granular rockwool. A commercial plug medium (Tosilee) was used as the control. All seeds were sown in 200 cell plug trays on November 28, 2001. Seedling growth was measured at 31 days after sowing. Each treatment showed a similar growth result as compared to the control. Plant height, root grade, fresh weight, and air space and bulk density of the medium were significantly greater in the 33% CGF＋67% peatmoss treatment than those in the other media. However, growth was slightly suppressed in the 50% CCW＋50% peatmoss. pH and EC of the media were the highest in the control treatment, although no toxicity symptoms had been observed. The results suggest that perlite can be replaced with a new material such as CGF in the commercial scale production of plug seedlings of 'Seogun' tomato.

• Journal of KIISE:Computer Systems and Theory
• /
• v.33 no.1_2
• /
• pp.44-51
• /
• 2006

In this paper, we present a network-based integrated nesting system, that is adapted a current engineering concept. Generally, sheet cutting processes proceed in turn following an existing order In this study, however, the special characteristics of these processes were analyzed and the processes were redesigned with distributed design so that they could be operated in a client/server environment. Also, the necessary sheet material cutting processes, part CAD, nesting, part CAM, and NC post-processor capabilities, were implemented so that many workers could handle them all on the Web. Compared to existing commonly used systems, the developed system can provide integrated work environment for cutting automation, allow job collaboration between workers, and it has proved that it can shorten the standby time for work. By grafting computer system technologies to sheet material cutting automation field, this research expects to contribute to the enhancement of factory automation efficiency and productivity.