• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.1
• /
• pp.20-26
• /
• 2005

Ultrasonic guided waves have been widely employed for long range inspection of structures such as plates, rods and pipes. There are numerous modes with different wave velocities, and the appropriate mode selection is one of key techniques in the application of guided waves. In the present work, phase tuning by an array transducer was applied to generate ultrasonic guided waves. For this purpose, 8-channel ultrasonic pulser/receiver and their controller which enables sequential activation of each channels with given time delay were developed. Eight transducers were fabricated in order to generate guided waves by using an array transducer. The selective tuning of wave mode can be achieved by changing the interval between elements of an array transducer.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.2
• /
• pp.114-121
• /
• 2009

Ultrasonic guided waves have been widely utilized for long range inspection of structures. Especially, development of array guided waves techniques and its application for long range gas pipe lines(length of from hundreds meters to few km) were getting increased. In this study, focusing algorithm for array guided waves was developed in order to improve long range inspectability and accuracy of the array guided waves techniques for long range inspection of gas pipes, and performance of the developed techniques was verified by experiments using the developed array guided wave system. As a result, S/N ratio of array guided wave signals obtained with the focusing algorithm was increased higher than that of signals without focusing algorithm.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.3 s.192
• /
• pp.16-22
• /
• 2007

• Journal of the Korean Institute of Gas
• /
• v.19 no.5
• /
• pp.29-35
• /
• 2015

Pipes, commonly used in energy and petrochemical facilities, have various types of defects induced by diverse factors and this is often issued in NDE society. Ultrasonic guided wave inspection method are normally adopted to insure the healthiness of industry pipes. Recently, ultrasonic guided wave inspection is shifted to adopt arrayed probes and system. And here we developed an array guided wave ultrasonic testing system can adapt arrayed probes and focusing methods. In this paper, an array guided wave ultrasonic testing system is presented including a transmitting focusing technique and flaw signal level enhancement.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.699-704
• /
• 2008

This paper describes a general approach for processing data from an omni-directional guided wave transducer array for the rapid inspection of large plate structures. A basic phased array algorithm is presented that can be applied to any array Geometry. For guided waves on plate, beam steering algorithm is derived and the corresponding beam pattern is analyzed. The algorithms are applied to simulation and experimental data. The results show well its usefulness in structural applications.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.1
• /
• pp.56-63
• /
• 2009

This paper describes a general approach for processing data from an omni-directional guided wave transducer array for the rapid inspection of large plate structures. A basic phased array algorithm is presented that can be applied to any array geometry. For guided waves on plate, beam steering algorithm is derived and the corresponding beam pattern is analyzed. The algorithms are applied to simulation and experimental data. The results show well its usefulness in structural applications.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.4
• /
• pp.367-373
• /
• 2011

Guided waves inspection techniques that are different with inspection technique by bulk waves are widely used in pipe line evaluation due to advantages of long distance inspection. However, most of pipe lines at industrial fields are buried and/or coated. In this case, due to the attenuation effect from soil and/or coating material, there are a lot of difficulty on inspection by conventional ultrasonic technique. In this paper, guided waves propagating patterns are calculated with respect to excitation mode by Normal Mode Expansion(NME). Guided waves patterns based on excited by single transducer and guided wave focusing technique have employed to analyze focusing pattern on a pipe. A longitudinal mode and high order flexural modes are used with various number of transducers to determine sensitivity. Guided waves energy excited by multi transducer with focusing algorithm was successfully focused at a desired point.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.2
• /
• pp.136-141
• /
• 2004

A torsional guided wave mode was applied to detect a crack in a pipe. An array of electromagnetic acoustic transduce. (EMAT that can generate and receive torsional guided ultrasound with the frequency of 200kHz was designed and fabricated for testing a pipe of 2.5 inch diameter Artificial notches with various depths were fabricated in a bent feeder pipe mock-up and the detectability was examined from the distance of 2m of the specimen. The axial notches with the depth of 5% of wall thickness were successfully detected by a torsional mode (T(0,1)) generated by the EMAT However, it was found that the depth of defects was not related to the signal amplitude.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.215-216
• /
• 2009

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.474-475
• /
• 2009