• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.264-267
• /
• 2005

수소의 소규모 분산 생산 기술은 본격적 인 수소 인프라가 도입되기 전에 연료전지 자동차의 수소 충 전용이나 분산 발전형 연료전지의 수소 공급을 위해 필요하다. 생산 용량은 수소 기준으로 $10\~100 Nm^3/hr$ 정도로 현재로선 천연가스의 수증기 개질법이 가장 경제적인 공정으로 알려져 있다. 소규모 생산에 따른 열효율 저하를 줄이 기 위해 단위 공정들이 통합된 컴팩트 개질 시스템의 개발이 필요하다. 핵심 기술인 컴팩트 리포머의 국산화 기술 확보를 위하여 $20 Nm^3/hr$용량의 동심관형 리포머를 설계, 제작하였다. 내부구조는 제작의 단순화를 고려하여 중첩된 동심관이 배열되었고 압력 손실과 열웅력 발생을 억제하도록 유로를 배치하였다. 수증기개질 반응에 필요한 반응열은 리포머 본체에 부착된 버너를 이용하여 공급하였다. 성능 측정을 위한 부속 기기로 상온 흡착식 탈황기, 폐열 회수형 수증기 발생기, 반응물 예열을 위한 열교환기, 생성 가스 응축기를 설계 제작하여 전체 리포밍 시스템을 구성하였다. 반응 온도 $680\~720^{\circ}C$, 탄소 대 수중기 비(S/C ratio) $2.7\~3.2$ 조건에서 수증기 개질 반응을 수행하였다. 해당 반응 조건에서 메탄 전환율 $89\%$ 이상, 저위 발열량 기준 개질 열효율 $70\%$ 이상을 달성하였고 개질 생성가스 내 수소의 최대 유량은 $23.4Nm^3/h$였다. 개발된 리포밍 시스템은 고순도 수소 생산이 필요한 경우, 수소 수율 향상을 위한 고온 수성 가스 전화 반응기를 통합 가능하도록 열교환기 구성을 조정할 수 있으며 용융 탄산염 연료전지와 같이 고온형 연료전지의 경우 $550^{\circ}C$ 이상으로 개질 생성 가스를 공급하도록 구성할 수도 있다. 향후 리포머 본체의 개질 효율 향상 및 장치 소형화, 부속 기기의 최적화를 통한 전체 리포밍 시스템 개선, 스케일 업 설계를 위한 엔지니어링 설계 패키지 구성을 계획하고 있다.

• Journal of the Korean Society of Safety
• /
• v.22 no.5
• /
• pp.77-83
• /
• 2007

This study is conducted on spontaneous ignition temperature and activation energy of Hydroxypropyl Methyl Cellulose(HMC) powder. HMC is a kind of cellulose derivative and used as additives for building material, surface coating, printing ink, adhesives, cosmetics and medical supplies. So this material has been widely used as important additive in the chemical industry fields and a mount of production has increased year by year. Therefore, it is very important to find out the thermal ignition characteristics of its danger and the critical ignition temperature. This study was performed by the Spontaneous Ignition Tester(SIT) and so on. Based on the data of the SIT-II, the critical ignition point of HMC is about $186^{\circ}C$ which is slightly lower than normal cellulose.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.7
• /
• pp.1641-1646
• /
• 2010

Recently, environmental concerns increased, CNG fuel research for the prevention against air pollution is actively. But, the problems of CNG fuel have less output and a shorter charging distance than gasoline. Especially, the causes of the torque and output reduction are the mixed fuel has a combustion timing loss in case of CNG fuel which has a smaller heating value per a unit volume and a slower flame propagation speed than gasoline. In this paper, we design the spark advanced controller in consideration of the spark timing loss. Through the experimental of chassis dynamometer, we show that maximum power and torque have improved compared to that of general CNG bi-fuel system.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.73.1-73.1
• /
• 2011

석탄가스화 복합발전(IGCC) 시스템은 고온 고압으로 운전되는 가스화기에서 미분탄을 산소와 함께 가스화하여 주로 CO 및 $H_2$를 생성하고 이때 발생되는 먼지 및 황성분은 각각 집진기 및 탈황장치에서 제거되며, 석탄 회분은 고온에서 용융되어 슬래그의 형태로 배출되는 방식을 사용하고 있다. 본 연구에서는 석탄가스화 복합발전시스템 설계에 필요한 기본자료를 파악하기 위해서, 고온 고압의 운전조건에서 1일 3톤의 석탄을 처리할 수 있는 Bench Scale급 석탄가스화기를 이용하여 가스화에 사용된 원탄 및 가스화기 설비의 각 지점에서 샘플링한 고체 시료를 중심으로 열화학적 특성을 살펴보았다. 가스화 실험은 아역청탄 계열의 ABK 석탄을 대상으로 가스화기 내부의 온도와 압력을 $1400{\sim}1450^{\circ}C$, $7.5{\sim}7.6Kg/cm^2$로 유지시키면서 실시하였다. 실험에 사용된 석탄 시료의 기본적인 물성치를 조사하기 위하여 표준방법에 따라 석탄의 공업분석, 원소분석, 발열량분석 등을 실시하였다. 석탄가스화기에서 배출된 슬래그와 대상 석탄 회분의 특성을 파악하기 위해서 XRF를 이용한 회분의 성분분석, Heating Microscope를 이용한 회분의 용융점 분석, XRD를 이용한 회분과 슬래그내의 화합물의 형태 및 결정구조 파악, SEM을 이용한 슬래그의 형상 등을 분석하였다. 또한 석탄가스화기 시스템을 구성하는 각 설비의 특성을 파악하기 위해서 관련 설비의 특정 지점에서 채취한 시료의 입도분석, 원소분석, 촤 회분 무게비, 슬래그중의 잔존탄소함량, 슬래그와 슬래그로부터 제조된 용출수내의 중금속 함량분석 등을 실시하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.609-617
• /
• 2017

Railways are one of the safest and most important transportation systems in the world. On the other hand, due to the increasing complexity of the railway system and the running distance of rail vehicles, railway accidents occur continuously every year. In particular, in the case of high-speed trains and freight trains, if the function of the axle bearing is lost due to abnormal overheating of the axle box bearing, the load on the axle becomes uneven. Therefore, abnormal overheating in the train axle box bearings can cause serious accidents or derailments. For this purpose, a Hot Box Detector (HBD) was installed in the track side of a high speed line to detect abnormal overheating. This paper proposes an EWMA technique-based axle temperature monitoring method to detect abnormal overheating quickly and efficiently. A statistical design of the proposed method was also performed. The proposed method has better performance compared to the current method in the case of abnormal overheating and the performance is improved by approximately 170% at the maximum.

• Fire Science and Engineering
• /
• v.26 no.2
• /
• pp.53-58
• /
• 2012

In this study fire control characteristics for inflammable materials of water curtain system are experimentally analyzed. Heat release rate for pinewood and gasoline was calculated using Room Corner Tester (RCT) and fire test apparatus for water curtain system is manufactured. Nozzles (180 degree of injection angle, 8.2 mm of orifice diameter) are installed at the nearby ceiling of place at 5 m distance from fire originate and temperature profile as well as transmission are obtained from the fire experiment of pinewood and gasoline in the water curtain system. Based on the results, parameters of engineering importance for fire control characteristics of water curtain system such as generation of high temperature smoke and thermal phenomena of fluid flow by injection nozzle are identified.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.940-946
• /
• 2015

In this paper, we study a method that amplifies the output gain of a high voltage pulse using 300 kHz or higher frequency. We conducted a study on a method for amplifying the output gain using the resonance between the capacitance components of the load and the parasitic components of the circuit, instead of the conservative method for amplifying the pulse-amplitude by raising the voltage of the power stage. In particular, the method simplifies the circuit configuration throughout the appliance of flyback-type topology instead of the bridge-type. There are advantages that prevent damage from overload and the heat in the output circuit through the hard switching by amplifying the gain of the output voltage applying to the load as given by the capacitance component of the output electrode to the output pulse waveform. This study proposed a method to enhance the spatial and electrical efficiency of the contact-type heating device through the dielectric heating method applied to the field of medical and industrial heating.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.119-125
• /
• 2004

This paper is described the indirect induction heated boiler system and induction heated hot air producer using the voltage-fed series resonant high-frequency inverter which can operate in the frequency range from 20〔KHz〕 to 50〔KHz〕. A specially designed Induction heater, which is composed of laminated stainless assembly with many tiny holes and interconnected spot welding points between stainless plates, is inserted into the ceramic type vessel with external working coil. This working coil is connected to the resonant inverter. In the induction heater, it's primary heating section creates low-pressure saturated steam and secondary heating section generates heat distribution evaporating fluid from the turbulence fluid which is flowing through the vessel. The operating performances of this unique appliance in next generation and its effectiveness are evaluated and discussed from the practical point of view.

• The Journal of Engineering Geology
• /
• v.21 no.2
• /
• pp.157-162
• /
• 2011

Experimental tests have been performed to measure the thermal conductivity of unsaturated soils, and computational models have been widely used to predict thermal conductivity. However, measured values of the thermal conductivity of unsaturated soils cannot be compared with predicted values because of the gradient in moisture content within unsaturated soils. In this study, experimental consolidation tests on saturated unfrozen kaolinite were performed to investigate the effect of dry density and moisture content on thermal conductivity. The results were used to evaluate the validity of a model employed to calculate thermal conductivity.

• Fire Science and Engineering
• /
• v.14 no.1
• /
• pp.8-12
• /
• 2000

We had investigated thermal and ignition behaviors of textiles. Decomposition of textiles with temperature was investigated using a DSC and the weight loss according to temperature using a TGA in order to find the thermal hazard of textiles, and the ignition behaviors of textiles according to species and permeation amount of oil. In addition, ignition behaviors of those permeated into oils indicating different iodine value and of those with arid without air in reaction vessel of measuring equipment were studied with constant temperature method among ignition temperature measuring methods. As results, the range of decomposition temperature of synthetic fiber was slightly broad compared with that of natural fiber, pure cotton. Besides, the initiation temperature of heat generation of both samples riced in the case of no air injection in the reaction vessel. On the other hand, in the case of air injection that was lowered according to the increase in permeative amount of oils and fats and decreased quickly as sample was permeated into drying oil.