• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.383-386
• /
• 2005

철근콘크리트 부재가 하중을 받을 때, 응력교란구역에서의 힘의 흐름은 스트럿-타이 모델을 이용하여 효과적으로 표현할 수 있다. 그러나 스트럿-타이 모델을 이용하여 철근콘크리트 부재의 해석과 설계를 하기 위해서는 큰크리트 압축스트럿이 가지는 유효강도를 정확히 산정하여야 한다. 본 연구는 철근콘크리트 부재에 휨과 전단력이 동시에 작용할 때 발생하는 대각선 균열이 콘크리트 압축스트럿에 미치는 영향에 대해 설명하고 있다. 대각선 균열의 발생 메커니즘과 이로 인한 콘크리트 압축스트럿의 강도 저하를 이론적으로 설명하였으며, 그 결과를 철근콘크리트 보의 강도 산정에 적용하였다. 최종적으로 철근콘크리트 보의 강도 예측값을 기존 연구자들의 실험결과와 비교하여 제안된 이론의 합리성을 검증하였다.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.5
• /
• pp.5-12
• /
• 2006

In this study a series of tests (bench scale test) are carried out for increasing the strength of clayey soil by EK-Injection method. In addition, the effects of strength increase in the treated sample are measured by operating the vane shear test device during 25 days at 5 days intervals in order to estimate the effect of ground improvement caused by diffusion. Also, the effects of strength increase in the treated sample are measured by operating the vane shear test device to estimate the effect by treatment durations (5, 10, 15, 20, 25). The test results show that the strength increase was developed approximately 2 to 7 times in comparison to initial shear strength, and outstanding strenfth increase was created as much as 7 times while injecting the sodium silicate and phosphoric acid in anolyte and catholyte. In addition, the measured shear strength with the influence of diffusion and reduction of water-content had a tendency to converge in constant value in proportion to elapsed time. As a result of this study, strength increment developed by the influence of EK-Injection and diffusion rather than the reduction of water-content was 1000% high on average. In case of changes of treatment duration, strength increment developed by the influence of treatment durations rather than the reduction of water-content was 3 to 4 times high on average.

• Journal of Korean Society of Steel Construction
• /
• v.10 no.2 s.35
• /
• pp.303-315
• /
• 1998

Four types of repair procedures are applied to the fatigue cracked crane runway gilders, which are stop-holes as crack arrester stop-holes reinforced with high strength bolts, welding repair and reinforcement with high strength bolted splices. The fatgiue cracks are reinitiated at the region where stop-holes and weld repairments are applied, while none of the cracks are observed in the cases of stop-holes reinforcement and reinforcement with high strength bolted splices. When using stop-holes and hole-reinforcement all repaired regions show a same fatigue strength to the one before the repairments. The experiments also reveal that the proper weldment is an essential factor when applying the welding repairement as a properly welding produces the same level of fatigue strength after the repairement. When the situation permits to use reinforcement with high strength boilted splices, the experiments shows the repairment is the best possible method among the procedures available.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1322-1326
• /
• 2007

지구 온난화에 의한 엘리뇨, 라니냐의 발생은 한반도에 커다란 기후변화를 가져왔다. 이러한 변화는 연간 총 강우량은 크게 변화하지 않았지만 강우강도가 증가하고, 태풍의 규모가 커지는 등 홍수방어의 측면에서 상당한 어려움을 야기하고 있다. 2006년 태풍 '에위니아'와 이에 뒤이은 태풍과 중국 북부지방의 기단이 장마전선을 형성하며 사상 최고의 강우강도를 기록한 집중호우는 미래의 기후조건이 극단의 사상으로 변화하고 있으며 이에 따른 구조적/비구조적 대책이 요구됨을 단적으로 드러내는 예이다. 이러한 집중호우들의 결과로 발생하는 제방붕괴 등으로 인한 홍수범람은 수많은 인명과 재산의 피해를 발생시키고 있다. 따라서, 본 연구에서는 500년 빈도 홍수유출에 의한 제방붕괴모의를 실시하고 강원도 원주시에 대한 침수심과 범람범위를 도출하고, 해당 침수지역의 홍수위험강도(침수심${\times}$유속)를 구하였고, FEMA에서 제시한 바 있는 Downstream Hazard Classification Guidelines(USBR, 1988)의 사람 및 가옥에 대한 위험 정도를 도출하였으며, 이 자료들을 근간으로 하여 침수심과 범람범위의 정보를 포함하고 있던 범람지도와 지역별 홍수의 세기를 표현하는 홍수위험 정보를 GIS Tool(ArcView, ArcGIS, CAD 등)들을 이용하여 표출함으로써 좀 더 효율적이고 체계적인 홍수지도를 작성하였다. 본 연구의 결과로 작성된 홍수위험정보 지도(침수심, 유속분포도, 홍수위험강도)는 주민의 대피 이동시나 대피지구 선정, 홍수로부터 발생하는 피해에 대한 최적화된 대응 대비, 도시개발계획 수립시 개발지역의 선정 등에 기초자료로 사용될 수 있을 것으로 판단되었다. 다양한 정보를 포함하고 있는 홍수정보 지도의 작성을 통해 기존 침수깊이와 범람범위의 1차적인 정보에서 수립할 수 있었던 계획이 가질 수 있었던 한계점을 좀 더 향상된 정보를 이용하여 극복함으로써 효율적이고 체계적인 치수 방재 계획수립이 가능할 것으로 판단된다.

• The Journal of Engineering Geology
• /
• v.16 no.3 s.49
• /
• pp.275-282
• /
• 2006

This study was conducted laboratory flume tests to identify landslide features and flow characteristics of debris using a flume test equipment. Under the several test conditions dependent on rainfall intensity and slope angle, the authors measured pore water pressure, slope failure and displacement, spreading area of debris on a regular time interval. The test processes were also recorded by video cameras and digital still cameras. According to the test results, pore water pressures have trends of direct proportion to the rainfall intensity and the slope angle, resulting in high potential of landslide triggering. The spreading area of debris is also increased with the slope angle and the rainfall intensity as well as the rainfall duration.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.34-34
• /
• 2019

급격한 기후변화의 영향으로 강우의 발생패턴과 높은 강우강도를 갖는 호우의 발생빈도가 높아지고 있어, 짧은 시간동안 다량의 표토가 손실될 가능성이 증가하고 있다. 강우에 의한 표토손실은 다양한 영역에서 발생하는데, 특히 산지유역과 농경지에서 발생할 경우 산림자원의 손실과 작물을 재배할 수 있는 영역이 감소하는 문제를 가져오게 된다. 또한 침식된 표토가 하천으로 유입되면 퇴적으로 인한 통수능력 저하, 하천생태 교란 등의 다양한 문제가 나타나고 있다. 우리나라는 표토침식량을 추정하기 위하여 연평균 토양침식모델을 적용하고 있다. 이모형은 기본적으로 연평균 토양침식을 예측하기 위해 개발되어온 모형으로, 적용하고 있는 매개변수도 연평균 개념의 값을 가지고 있다. 따라서 이모형은 짧은 시간동안에 발생하는 호우사상으로 발생하는 표토침식을 예측하는데 한계를 가진다. 본 연구에서는 기후변화의 영향으로 나타나는 단기호우사상에 의한 표토침식을 예측하기 위해 외부에서 작용하는 침식요인인 강우강도를 고려하기 위하여, 강우입자의 물리적인 특성을 반영한 강우에너지 산정공식을 제시하였다. 또한 기 개발된 분포형 단기표토침식모형에 제안된 식을 적용하여 타당성을 검토하였다.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.5
• /
• pp.117-128
• /
• 1998

화학적으로 유해한 환경에 놓인 콘크리트 구조물은 필연적으로 그 기능이 악화되므로 혼화재를 포함한 고강도 콘크리트 또는 혼화재 그 자체가 화학물질에 오염된 환경하에서 어떤 변화를 일으키는가에 대한 연구의 필요성이 점점 증대되고 있다. 따라서 본 논문에서는 건설현장에서 가장 흔히 사용되는 보통강도 콘크리트와 실리카-흄을 포함한 포틀랜드시멘트 경화체인 고강도 콘크리트가 황산염의 침해를 받는 경우에 일어나는 강도특성과 물성변화를 조사하기 위하여 담수와 함께 황산나트륨, 황산마근네슘, 황산나트륨과 황산마그네슘의 혼합용액 등 여러종류의 황산염 용액에 실리카-흄을 사용한 고강도 콘크리트, 낮은 물-시멘트 비의 고강도 콘크리트, 보통강도의 콘크리트 등의 시험체들을 270일간 침지시켜 침지시간에 따른 압축강도 변화와 실리카-흄의 첨가량에 따른 압축강도 변화, 그리고 실리카-흄의 첨가량에 따른 선형팽창량 및 중량변화등에 관한 실험을 수행하였다. 이에 대한 실험결과를 토대로 실리카-흄을 사용한 고강도 콘크리트에 황산염이 미치는 영향을 분석하여 고강도 콘크리트의 실용성을 극대화하기 위한 방안에 대하여 고찰해보았다. 그 결과 실리카-흄을 포함한 고강도 콘크리트는 황산나트륨의 침해에 대해서는 강한 저항성을 나타내지만 황산마그네슘에 대해서는 심각한 침해를 일으키는 것으로 나타났으므로 황산마그네슘에 노출될 우려가 있는 콘크리트 구조물에 고강도를 발현하기 위하여 실리카-흄을 사용하는 것은 구조적으로 큰 문제가 발생할 것으로 사료된다.

• Journal of forensic and investigative science
• /
• v.2 no.2
• /
• pp.5-20
• /
• 2007

During the period from 2001 to 2005, 29,892 burglaries took place in Korea with the approximate average annual number - 5,978 cases. This study was conducted to analyze the reported burglaries and the result was summarized as follows. There were 8,605 residential invasion burglaries (28.8%) as the most frequent characteristic pattern. The exit was used as the most frequent invasion route for 4,031 invasion burglaries (64.3%), and an unlocked exit door or window was used as the most frequent invasion method for 2,462 invasion burglaries (28.6%). The hours just after midnight (between 00:00 and 04:00) were the most frequent time for invasion burglary to occur. Also, 5,652 burglaries occurred on Wednesday which was twice higher than on Sunday (2,988 burglaries). It was shown that the number of persons injured during burglaries were 260 deaths and 10,610 injuries. The places of the highest occurrence were the street with 10,183 burglaries (34%) and then residential place with 7,527 burglaries (approximately 25%). One-man burglary was the highest complicity: 15,012 offenders (56.1%). The knife was used as the most frequent instrument for 6,498 burglaries (24,3%) what is rare, while no criminal tool or instrument was used for 15,631 burglaries (58.4). During the period from 2001 to 2006, 1,506 burglaries occurred in Daegu and the average annual number was 251 burglaries. Among those,515 residential invasion burglaries (34.2%) took place and the average annual number was approximately 86 cases. The hours just after midnight (between 00:00 and 04:00) were the most frequent time for invasion burglary to occur (194 cases, 37.7%), the place of the highest invasion occurrence was the residential place (259 cases, 50.3%), and the exit was used as the most frequent invasion route (87 cases, 37.7%). An unlocked exit door or window was the most frequent invasion method (65 cases, 25.1%). In addition, pretending to be a delivery man, visitor or following the victim methods were used for 26 burglaries (10%). It is apparent that personal preventive measures against crimes, as well as governmental and social measures, play an important role in preventing burglaries. In particular, based on the analyzed result that an unlocked window or exit door was most frequently used for reported burglaries, it seems that there is a lack of understanding of crime prevention while little effort has been made to prevent crimes. Although everyone knows that locking a door is one of the basic measures to prevent crimes, many people tend to pay little attention to lock a door properly so burglary takes place. This study, therefore, is intended to encourage people to pay more careful attention to crime prevention, in order to help reduce the probability of burglary. With the recent improvement in social understanding of scientific crime investigation, a wide variety of police professions, including crime analysts, crime victim police counselors and coroners, have been prepared to develop the scientific crime investigation and crime analysis. In addition, it is hoped that further this study will contribute to encourage studies on crime prevention to be carried out in the future.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.26 no.4
• /
• pp.405-417
• /
• 2010

Previous studies have already shown that mouthguard is effective in protecting jaw bone, teeth and oral tissue against sports trauma. However, other than severe trauma, repetitive force, such as disorders like clenching, cause teeth or oral tissue damage. These kinds of disorders usually present pathologic attrition in the posterior teeth, resorption in alveolar bone, loss of teeth and destruction of occlusion. Wearing a mouthguard is believed to be effective in preventing these disorders. But its effect is not examined thoroughly enough. The purpose of this study is to identify whether mouthguard is effective in reducing strain caused by clenching. Mandibular first molars in the normal occlusal relationship without any history of dental treatment were chosen. Biaxial type strain gauge was placed on the buccal surface of the tooth. Having maximum occlusal force, measured by load cell, as a standard, clenching intensity were divided into three stages; moment of slightly tooth contact, medium bite force (50% of maximum bite force), maximum bite force. Strain occurring in dentition in each stage with and without mouthguard was measured. Changes in strain (on dentition) between each stage and difference in strain, between with or without mouthguard were recorded by PCD-300 analyzer and PCD-30 soft ware. The data was statistically analyzed by Wilcoxon signed rank test. The following results were drawn; Without mouthguard, strain given on dentition increased as the clenching force increased. With mouthguard, strain given on dentition also increased as the clenching force increased. With mouthguard, strain decreased, in all cases of clenching force stages. Data on the moment of slightly tooth contact stage, had no statistical significance. However, with mouthguard, 50-90% of decrease in strain could be obtained in maximum occlusal force, compared to the group without mouthguard. Mouthguard decreased the strain on the dentition, caused by clenching. Therefore, mouthguard seems to be effective in preventing damage on dentition, by acting against clenching, which occurs both consciously and unconsciously during sports activities.

• Journal of the Korea Concrete Institute
• /
• v.26 no.4
• /
• pp.465-474
• /
• 2014

This is a comparative study that shows the overall environmental impacts from concrete structures when different compressive strength of concrete applied to structural systems having the same reference flow with different durability. A total of 24 MPa, 40 MPa and 60 MPa cases is analyzed to define the characteristic using end-point perspective LCA methodology including the stages of production, construction, maintenance and disposal. As results, global warming, non-renewable energy and respiratory inorganics problems are the major issues for assessing environmental impacts of concrete products.