• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.7
• /
• pp.643-649
• /
• 2013

In this paper, human heartbeat detection using signal reflected from the antenna which is varied reflection coefficient by near field variation of the antenna. For detection reflected signal from antenna, 20 dB directional coupler is used because of not affecting transmitting signal. Variance of reflection coefficient of dipole antenna is about 0.07 dB which is too small the distinction between heartbeat and noise. Sensitivity increasing method is applied and heartbeat is clearly detected. Due to phase and magnitude errors come from discrete value components, antenna is located some points in experiments ro find optimum sensitivity position. And providing verification of using communication signal, heartbeat detection when frequency modulated signal which have 4 MHz bandwidth is applied.

• Journal of Korea Spatial Information System Society
• /
• v.5 no.1 s.9
• /
• pp.39-47
• /
• 2003

The purpose of this paper is to present the method of acquiring 3D GIS data using the statistical estimating methods of Well Log for balancing Seismic data. We use the reflection coefficients of seismic data to get the parameters for the reservoir characterization and we balance the reflection coefficients of seismic data using well log to increase the confidence of the estimated result. Well logs are required to balance the reflection coefficients at the point where seismic data are acquired. In this research, we discuss the geostatistical estimation methods and we applied these methods to real data. Kriging gives high weights to the close well logs, which means estimated results are mainly affected by close well log. High value of cross variograms gave big difference on cokriging result comparing to kriging results and low value of cross variogram gave little differences.

• Geophysics and Geophysical Exploration
• /
• v.1 no.3
• /
• pp.183-187
• /
• 1998

Seismic waveform estimation is based on the assumption that the seismic trace tying a well is one dimensional convolution of the propagating seismic waveform and the reflectivity series derived from well logs (sonic and density). With this assumption, the waveform embedded in a seismic trace can be estimated using a Wiener match filter. In this paper, I experimented a preprocessing procedure that applies both on the seismic trace and on the reflectivity series. The procedure is based on the assumption that the travel time can be estimated better from the seismic trace and that the instantaneous reflectivity values can be measured better on the well log. Thus the procedure is, 1) start-time adjustment and dynamic differential stretches are applied on the sonic log, and 2) seismic amplitudes are balanced such that the low frequency part of the seismic are matched to that of the reflectivities derived from well logs.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.12
• /
• pp.1269-1274
• /
• 2014

Since power and control cables have narrow bandwidth due to their loss at high frequencies, it is difficult to detect the weak fault using conventional reflectometry. It is because the reflected wave caused by the weak fault is overlapped and hidden by the ripple of the strong reflected wave from the end of the cable. This paper proves that the reflected wave from the weak fault can be considered to be linearly superposed on the strong reflected wave from the end of the cable based on the transmission line theory. Then, the weak fault point is experimentally diagnosed using the difference between reflection coefficients before and after the fault generation.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.39 no.3
• /
• pp.239-248
• /
• 2003

This paper was conducted as an attempt in order to construct the data bank of target strength for acoustic estimation of fish length in the coastal waters of Korea. The fish length dependence of acoustic target strength for 13 large yellow croakers (Pseudosciaena crocea) at 75 kHz was investigated and the prediction of the target strength by using the Kirchhoff-Ray Mode model (KRM model) was compared with target strength measurements. The results obtained are summarized as follows; 1. In the averaged target strength pattern for 13 large yellow croakers the maximum target strength was -35.13 dB at $-13.35^{\circ}$ on a tilted angle. 2. The relationship between fork length(L, cm) and averaged target strength(TS, dB) was expressed as follows; TS=23. 76log (L) -73.45 (r=0.47) TS=20log(L) -67.35 From this result, the conversion coefficient was -73.45 dB and 6.1 dB lower than the coefficient -67.35 dB where the value of the slope of the regression equation is forced to be 20. 3. Averaged target strength and a length conversion coefficient derived from a target strength histogram for 13 large yellow croakers of mean length 25.59 cm were -41.23 dB, -69.72 dB, respectively. 4. In the range of $$2;{\ll} L (fish length /{\lambda}(wave length);{\ll}40$$, the prediction of the averaged target strength by the KRM model increased gradually with the increasing of $L/{\lambda}$ and was lower than the measured target strength.

• Journal of Biomedical Engineering Research
• /
• v.18 no.4
• /
• pp.499-505
• /
• 1997

A non-invasive technique to measure absorption and scattering coefficients was investigated The reflected backscattered light from the surface of phantom and biological tissue was obtained by using a time-correlated single photon counting system in pico-second time domain. The absorption and scattering coefficients were acquired by the time of peak and asymptotic behavior of the time-resolved reflectance curve and agreed well the ones that is obtained with deconvolution method It was found that the approximation method was good for biological medium to calculate optical properties due to its convenience and accuracy.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.300-303
• /
• 2001

개방단말 동축선 프로브는 임의의 매질에 접촉하여 복소 유전율을 구하므로 사용이 용이한 측정법이다. 복소 유전율의 측정 과정은 두 단계로 구성된다. 먼저 프로브의 개구면을 미지의 매질에 접촉시켜서 반사계수를 측정한다. 다음에는 반사계수를 환산모델에 대입하여 복소 유전율을 구한다. 그러나 실제 측정시 발생하는 오차들에 대해 취약하다는 단점을 가지고 있다. 정확성을 떨어뜨리는 주요 오차 요인으로는 프로브의 개구면과 측정매질 사이의 공극으로 인한 불완전 접촉오타와 프로브의 제작 한계로 인한 오차를 들 수 있다. 본 논문에서는 이런 오차상황에서 유한 차분 시간영역법으로 반사계수를 계산하고나서 환산모델에 의해 복소 유전율로 환산함으로써 오차에 대한 환산모델들간의 안정성을 살펴보고자 한다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.12A
• /
• pp.1346-1353
• /
• 2007

In this paper, the methods are presented for the calculation of general coupling coefficient matrixes used in the band pass filter design. They are calculated from transmission coefficient($S_{21}$) and reflection coefficient($S_{11}$) with desired characteristics derived from the poles of filter function and return loss(RL). The calculated matrixes from this method are transformed to the folded canonical filter structure using similarity transformation which lends us the practical filter design. Based on the resulting matrix, the folded canonical filter has been designed.

• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.287-292
• /
• 1999

동해 38도 10분N, 132도 00분E(site 1)과 38도 01분N, 132도 53분E(site2)에서 저주파수를 이용한 해상실험자료를 이용하여 해저면 음파반사 특성을 파악하였다. 음원으로는 한국해양연구소 온누리호에 장착되어 있는 총 11.31l의 부피를 가지는 에어건 array를 사용하였고 수신장치로는 총 56채널로 이루어진 아날로그 스트리머를 사용하였으며, 각 실험위치에서 3번씩 신호를 수신하였다. 관측해역에 대해 eigenray 모델을 이용하여 에어건에서부터 각 채널까지의 eigenray 정보를 파악한 후 해저면 반사계수를 산출하여 Rayleigh reflection 모델과 비교하였다. 비교 결과 Rayleigh reflection 모델은 해저면 반사 손실과 부합하는 것으로 나타났다.

• Korean Journal of Optics and Photonics
• /
• v.26 no.5
• /
• pp.275-282
• /
• 2015

The effective reflection coefficients for light obliquely incident upon a substrate coated with uniaxially anisotropic films and with isotropic films are derived. Multiple reflections inside anisotropic films, as well as those inside isotropic films, are properly treated. These expressions, together with the related ellipsometric expressions, can be used to find the nonuniform distribution of an uniaxially anisotropic film perpendicular to the film's surface, by approximating it as consisting of uniaxially anisotropic uniform layers and applying the conventional modeling technique for spectroscopic ellipsometry.