• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.954-957
• /
• 2004

Based on the authors' previous work, where a geometric constraint handling technique for stiffener layout optimization problem using geometry algorithms was proposed, stiffener layout optimization to maximize natural frequencies of a curved three-dimensional shell structure was performed with a projection method. The original geometry of the shell structure was first projected on a two-dimensional plane, and then the whole optimization process was performed with the projected geometry of the shell except that the original shell structure was used for the eigenproblem solving. The projection method can be applied to baseline structures with a one-to-one correspondence between original and projected geometries such as automobile hoods and roofs.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2003.05a
• /
• pp.27-31
• /
• 2003

Recently, buckling is easy to happen as that High tensile steel that is the thin plate absence is used comprehensively for the structure. Specially, buckling is getting into important design standard in hull construction which use High tensile steel. Therefore, that grasp conduct exactly after buckling is important in stability of hull structure. In this study, examined closely about conduct and secondary buckling after initial buckling of thin plate structure which receive compressive load according to various kinds yield strength under simply supported condition that make by buckling strength formula standard in each payment in advance rule to place that is representative construction of hull in this research. Analysis method is F.E.M by ANSYS and complicated nonlinear behaviour to analyze such as secondary buckling in used arc-length method.

• Computational Structural Engineering
• /
• v.11 no.4
• /
• pp.209-218
• /
• 1998

고장력강이 구조강재로서 널리 사용되고 있다. 구조물의 극심한 하중을 받게되면 최종강도에 도달할 때까지 좌굴을 동반하게 된다. 그러므로, 고장력강판의 좌굴에 대한 정확한 평가가 중요한 설계기준이 되고 있다. 그러나, 고장력강을 효율적으로 사용하기 위해서는 좌굴허용설계를 도입할 수 있도록 판구조물의 판두께가 얇아져야 한다. 따라서, 박판구조물의 합리적인 설계를 하기 위해서는 좌굴후거동해석이 매우 중요하다. 그러므로, 본 논문에서는 호장증분법을 이용하여 압출하중을 받는 박판구조물의 초기좌굴후거동과 2차좌굴강도에 대하여 규명하였다. 특히, 호장증분법을 좌굴정에서의 하중경로를 추정하기 위하여 적용하였다.

• Journal of Korean Society of Steel Construction
• /
• v.29 no.4
• /
• pp.323-330
• /
• 2017

The pre-engineered building(PEB) construction has been gradually applied to single story buildings as a practical and efficient alternative to conventional buildings. However, there has been a few structure collapse due to suddenly excessive load. Although a structure design requires accurate and professional skills, the PEB system tends to be designed simply because of complexation of structural analysis for connections. This paper shows the finite element analysis(FEA) using ABAQUS software on bolted connection which was previously tested. The FEA condignly simulated the behavior of bolted connection in PEB system and was in close agreement with experimental results. Then the stiffness reduction factor of the bolted joints that can be used in the actual design is presented through the analysis of the joint parameters.

• Proceedings of the KWS Conference
• /
• 2003.05a
• /
• pp.204-206
• /
• 2003

Ti/Steel 클래드 판재를 제조하기 위하여 티타늄과 강판을 직접 접합하는 경우 접합 계면에 취성이 강한 금속간화합물 및 TiC 탄화물이 발생하여 계면접합강도를 저하시키는 단점이 있다. 이러한 단점을 보완하기 위하여 본 연구에서는 티타늄과 강판 사이에 니켈 박판을 삽입한 후 1223-1323K 온도구간에서 접합 실험하였다. 특히, 온도의 변화에 따라 티타늄과 강판의 계면에 발생되는 금속간화합물의 종류 및 반응층의 크기 변화에 따른 기계적 특성을 조사하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.308-309
• /
• 2010

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.57-58
• /
• 2011

• Journal of Welding and Joining
• /
• v.22 no.4
• /
• pp.24-28
• /
• 2004

마이크로 접합 공정은 미세 부품이나 박판의 접합에 사용되며, 이를 위해 다양한 공정이 개발되었다. 최근 MEMS(Micro Electro Mechanical System)활용 범위가 증가하고 있으며, MEMS에 사용되는 미세한 구조물의 접합이나 패키징에 접합 공정이 활용되고 있다. MEMS는 발전 단계이지만 전자 패키징(electronic packaging)은 성숙 단계인 반도체 산업에 사용되고 있다.(중략)

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.18 no.1
• /
• pp.13-20
• /
• 2005

Since High Tensile Steel has been widely used to thin plate on the steel structure and marine structure, It has increased possibility of buckling. Especially, initial deflection of ship structure is mainly caused by heat processing of welding or cutting etc. This initial deflection has negative effect to thin plate, which would incur a complicated nonlinear behavior accompanied with secondary buckling. If idealized initial deflection is considered in early marine structure design of secondary buckling, accuracy and reliability will be improved considerably. The measurement data of initial deflection from experiment is applied to finite element series analysis. For FEA(ANSYS), Applied nonlinear buckling analysis is used by Newton-Raphson method & Arc-length method included in this program.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2002.11a
• /
• pp.95-100
• /
• 2002

The wing in ground effect (WIG) ship is an energy saying vessel that uses the lift from its air-wing along with the lift increase from the ground effect by flying low above the sea surface. The WIG Ship should consist of thin plate in order to float on the sea and to fly in the air. Therefore, the structure of WIG, Ship has very thin and light shell plate and stiffener like stringer and frame has comparatively large cross section area. This structure makes shell plate nearly pure shear field when shell plate is pressed by in-plane load. This complex thin plate structure of WIG Ship can he considered as a closed section beam which makes it possible to analyze structure response of WIG Ship affected by shear load and bending load. In this respect, the present study will show basic theory for analysing shear stress and focus on the analysis of structure strength of model WIC Ship's wing.