• Journal of Advanced Marine Engineering and Technology
• /
• 제23권6호
• /
• pp.778-784
• /
• 1999

In this study both the experimental and the analytic approach to find load characteristics on the cam-valve mechanism for matrine diesel engine were demonstrated. The experiment was per-formed with a test rig consisted of real engine components for cam-valve mechanism of overhead valve type. The 9-degree of freedom lumped mass model was developed to simulate cam-valve motion throughly. Behavior of the load acting on the cam-valve mechanism was estimated for the various cam speed. The load variation was getting deeper with the higher cam speed and the jumping of the follower was shown both in the experiment and in the simulation.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권6호
• /
• pp.147-154
• /
• 2000

A numerical procedure to analyze 3-dimensional elastohydrodynamic lubrication was applied on the cam-roller contact of the valve mechanism for a marine diesel engine. Both the pressure distribution and the film thickness between the cam and roller follower were calculated for each time step of the whole cycle. The pressure spike is shown at the outlet of the roller edge and it is getting higher as the external load is increased. An effective profiling method for the roller edge was suggested using the results of elastohydrodynamic lubrication analysis and the peak pressure was removed completely with the new profiling.

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권7호
• /
• pp.832-838
• /
• 2003

IMO NOx levels are generally possible to meet by means of primary on-engine measures. Nevertheless further significant follow-on reductions are likely to require a secondary after-treatment technique. SCR system is currently the only available technology proven at full scale to meet the 90% NOx reduction levels. Accordingly, maybe the use of an SCR system on board ship provides the solution to minimize this primary pollutant without increasing fuel consumption. In order to develop a practical SCR system for marine application on board ship, a primary SCR system using urea was made. The SCR system was set up on the ship. employed a two-stroke diesel engine as a main propulsion. which is a training ship in KMU (Korea Maritime Univ.). The purpose of this paper is to report the results about the basic effects of the above system parameters which is investigated from practical application through its trial use. The degree of NOx removal depends on some parameters. such as the amount of urea solution added, space velocity. reaction gas temperature and activity of catalyst. The preliminary results from trial run are presented.

• Journal of Advanced Marine Engineering and Technology
• /
• 제9권4호
• /
• pp.307-316
• /
• 1985

Nowadays, the natural frequencies and their relative amplitudes of torsional vibration for the marine diesel engine shafting are usually calculated by the Holzer method and also its resonant amplitudes are estimated by the energy method, that is, by equating the exciting energy to the damping one. Therefore, the forced vibration amplitudes out of the resonant points can not be calculated by the above-mentioned method. And so, the reasonable barred-ranges of torsional vibration can not be set and also the flank of resonant point which locates near the calculation limit can not be estimated. For such problems, the equation of forced vibration with damping must be solved directly and these results can be utilized to derive the synthesized torsional vibration of the marine diesel engine propulsion shafting. In this study, the equation of forced vibration with damping for the marine diesel engine propulsion shafting is derived and its steady-state vibration is calculated by the mechanical impedance method. For numerical calculation of the actual propulsion shafting a computer program is developed. In order to prove the reliability of this program, an actual ship's propulsion shafting whose torsional vibration was measured is analyzed and the calculated propulsion shafting whose torsional vibration was measured is analyzed and the calculated results are compared with the measured ones. And also, they are compared with the calculated results which were obtained by the modal analysis.

• Journal of Advanced Marine Engineering and Technology
• /
• 제10권2호
• /
• pp.146-155
• /
• 1986

Until recently, the calculation of torsional vibration for the marine diesel engine shafting has been performed only for vibratory stresses of resonant points and vibratory stresses for other engine speeds are determined by the estimation. With the advent of energy-saving engines which have a long stroke and a small number of cylinders, the first major critical torsional vibration of the propulsion shaft appears ordinarily near the MCR speed of engine and the flank of its vibratory stress exceeds now and then the limit stress defined by the rules of Classification Society. In order to know the above condition in the design stage of propulsion shafting, it is necessary to calculate the forced torsional vibration with the damping of propulsion shafting for all orders and to synthesize its calculated results according to their phase angles. In this study, the forced torsional vibrations with the damping of propulsion shafting are calculated for several orders by mechanical impedance method, and their results are synthesized. A computer program for above calculations are developed and some test-runs of the developed program are performed for propulsion shaftings of actual ships. The results of calculations are compared with measured values and also with those of the modal analysis method. They show fairly good agreements and the developed program is checked up on its reliability.

• 수산해양기술연구
• /
• 제30권4호
• /
• pp.320-328
• /
• 1994

In 1980 s to 1990 s the marine propulsion diesel engines have been developed into lower speed and longer stroke for the enegy saving (small S.F.O.C). As these new trends the conventional mechanical-hydraulic governors were not adapted to the new requirements and the digital governors have been adopted in the marine use. The digital governors usually use the control algorithms such as the PID control, optimal control, adaptive control and etc. While the engine has delay time and parameter variations these control algorithms have difficulty in considering the stability and the robustness for the model uncertainty. In this study, the $H_{\infty}$ controller design method are applied in order to design the feedback controller K(s) to the speed control of the low speed marine diesel engine, and the two-degree-of-freedom control system is constituted with $H_{\infty}$controller. By comparison of responses of the two-degree-of-freedom control system under the delay time and parameter variations is confirmed.

• Journal of Advanced Marine Engineering and Technology
• /
• 제21권2호
• /
• pp.195-205
• /
• 1997

The propulsion marine diesel engine have been widely applied with a mechanical- hydraulic governor to control the ship speed for long time. But it was recently very difficult for the mechani¬cal - hydraulic governor to control the speed of engine under the condition of low speed and low load because of jiggling by rough fluctuation of rotating torque and hunting by dead time of Desiel engnie The performance improvement of mechanical - hydraulic governor is required to solve these problems of control system. The electro - hydraulic governor using PID algorithm is provided to compensate the faults of mechanical- hydraulic governor. In this paper, in order to analyze the ship speed control system, the transfer function was converted from the z tansformation to w transformation. The influence of dead time changing by engine speed which induces hunting phenomena was investigated by Nichols chart of w plane. As a method of performance improvement of mechanical hydraulic governor, a Eletro - hydraulic governor shows that fine control results can be obtained through optimal parameter tuning of PID

• Journal of Advanced Marine Engineering and Technology
• /
• 제13권3호
• /
• pp.26-36
• /
• 1989

Recently digital governor system is commonly adapted for the speed control of the marine diesel engine because of too much fluctuation of rpm resulted by the low speed, long stroke, high efficiency and a small number of cylinder of it, and versatile studies on the development of digital governor system are progressed. On this subject the new control method in which the fuel is controlled by feedforwarding the change of load as well as the feedback of angular velocity in case of disregarding the engine dead time and influence of scavenging air was proposed by the authors, and found the method has shown quite a good control performance in comparision to the conventional control method by the simulation using a digital computer for various load change. In this paper the speed control system of a diesel engine is simulated in case of regarding the engine dead time by the proposed method, and also confirm a good control performance of it under even more realistically simulated environment.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제30회 추계학술대회
• /
• pp.121-128
• /
• 1999

In this study, a numerical procedure to analyze 3-dimensional unsteady elastohydrodynamic lubrication was developed. The procedure was applied to the actual cam and roller follower of the valve mechanism for a marine diesel engine. The pressure distribution between the cam and roller follower was calculated for the several cam rotating angles. The pressure spike is shown near the roller edge and it is getting higher as the external load is increased. The roller profile for reducing the pressure spike was suggested by the Hertzian contact analysis.

• Journal of Advanced Marine Engineering and Technology
• /
• 제12권4호
• /
• pp.53-61
• /
• 1988

Speed of a diesel engine is usually controlled by the hydraulic governor which uses the centrifugal force of rotating fly balls for sensing the error speed. But for a recently developed high efficient, low speed and long stroke 2 cycle marine diesel engine, this governor doesn't work well enough because of too much changes of toraring force during one revolution of engine and too long uncontrollable time due to small numbers of cylinder. For improvement of jiggling phenomena and unstability various studies are being carried out, but they are not enough for a steep load change in a small ship's generator plant or at rough sea condition in a propulsion engine. In this paper, authors propose a new method to control a fuel before the change of angular velocity due to load change by feedforward the change of load, and find that the proposed method shows quite a good control performance in comparision to the customary PID control method by simulation using a digital computer for the various load change.