• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.9
• /
• pp.882-888
• /
• 2002

This paper proposed a bias stability circuit that compensates the degradation of MMIC's performance for the variation of the process and temperature. The proposed bias circuit proved the superior effect compared with the conventional bias circuit using the constant current source. It designed and fabricated simultaneously two amplifier on one layout for comparison in same conditions. One is amplifier with conventional bias circuit using constant current source and the other is amplifier with proposed bias stability circuit. The chip was measured the microwave performances under process variation that classed the level NOM, MIN and MAX. The amplifier with a conventional bias circuit using constant current source has 6.4 dB gain variation and 7 mA Ids variation at 1.8 GHz, but the amplifier with the proposed bias circuit has the 2.1 dB gain variation and 3 mA Ids variation. As the result, MMIC having the proposed bias circuit shows the superior compensation of the quiescent point than the MMIC having the conventional bias circuit under the variations of the process and temperature and can improve the yield of the MMIC. The fabricated chip size is 1.2 mm $\times$ 1.4 mm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.7A
• /
• pp.672-677
• /
• 2007

A novel method for stabilizing the bias of an Electro-Optic Mach-Zehnder modulator has been proposed and demonstrated to maximize the switching extinction ratio in burst mode packet traffic. By sampling and minimizing the off-level output power of the modulator, a high extinction optical gate switch in obtain regardless of the variation of the packet traffic density.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.1B
• /
• pp.42-47
• /
• 2000

A new method for stabilizing the bias of an Electro-Optic mach-Zehnder modulator has been developed to maximize the switching extinction ratio in burst mode packet traffic. By sampling and minimizing the off-level output power of the modulator, a high extinction optical gate switch in obtain regardless of the variation of the packet traffic density.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.569-577
• /
• 1999

A wideband RF receiver for satellite mobile communications system was fabricated and evaluated of performance in low noise amplifier and high gain amplifier. The low noise amplifier used to the resistive decoupling and self-bias circuits. The low noise amplifier is fabricated with both the RF circuits and the self-bias circuits. Using a INA-03184, the high gain amplifier consists of matched amplifier type. The active bias circuitry can be used to provide temperature stability without requiring the large voltage drop or relatively high-dissipated power needed with a bias stabilized resistor. The bandpass filter was used to reduce a spurious level. As a result, the characteristics of the receiver implemented here show more than 55 dB in gain, 50.83 dBc in a spurious level and less than 1.8 : 1 in input and output voltage standing wave ratio(VSWR), especially the carrier to noise ratio is a 43.15 dB/Hz at a 1 KHz from 1537.5 MHz.

• Korean Journal of Optics and Photonics
• /
• v.9 no.2
• /
• pp.100-103
• /
• 1998

We proposed a simple and yet effective way of wavelength stabilization for WDM transmission using a temperature compensated fiber grating. This scheme was successfully applied to both DFB LD and EMLD, locking them to their respective reference wavelengths notwithstanding temperature change and RF modulation.

• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.1
• /
• pp.40.1-40.1
• /
• 2018

외계행성 탐색시스템 18k 모자이크 CCD 카메라는 4개의 9k CCD로 구성되며 총 32개 채널의 영상영역과 리드아웃 회로를 가진다. 관측 영상에는 각 영상영역에 대한 오버스캔(overscan) 영역이 포함되는데, 영상 신호에 의한 오버스캔 영역의 바이어스(bias) 교란을 최소화하기 위해 리드아웃 회로의 인버팅 앰프에 대한 Common Mode Rejection Ratio(CMRR)를 미세 조정하였다. 그 결과 세 사이트의 평균 CMRR이 55 dB에서 73 dB로 향상되었고, 기존에는 영상 신호에 따른 오버스캔 바이어스 레벨의 선형적 관계가 약 2/1,000의 기울기를 가졌으나 조정 후에는 약 2/10,000로 바이어스 오차가 줄어들었다. CCD 리드아웃 회로의 미세조정과 클락(clock) 개선을 통해 물결무늬 잡음 제거 및 읽기 잡음 감소가 이루어졌으며, 향후의 추가적인 바이어스 안정화와 크로스톡 개선 방안이 검토되고 있다. 카메라 전자부 조정 과정 및 결과와 더불어, 카메라 듀어와 부대장비 유지보수, Polycold CryoTiger 냉각기 운영 및 개선 관련 노하우도 함께 발표한다.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.2 s.35
• /
• pp.105-109
• /
• 2005

A compact antenna switch module for GSM/DCS dual band applications based on multilayer low temperature co-fired ceramic (LTCC) substrate is presented. Its size is $4.5{\times}3.2{\times}0.8 mm^3$ and insertion loss is lower than 1.0 dB at Rx mode and 1.2 dB at Tx mode. To verify the stability of the developed module to the process window, each block that is diplexer, LPF's and bias circuit is measured by probing method in the variation with the thickness of ceramic layer and the correlation between each block is quantified by calculating the VSWR In the mean while, two types of bias circuits -lumped and distributed - are compared. The measurement of each block and the calculation of VSWR give good information on the behavior of full module. The reaction of diplexer to the thickness is similar to those of LPF's and bias circuit, which means good relative matching and low value of VSWR, so total insertion loss is maintained in quite wide range of the thickness of ceramic layer at both band. And lumped type bias circuit has smaller insertion itself and better correspondence with other circuit than distributed stripline structure. Evaluated ceramic module adopting lumped type bias circuit has low insertion loss and wider stability region of thickness over than 6um and this can be suitable for the mass production. Stability characterization by probing method can be applied widely to the development of ceramic modules with embedded passives in them.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.9
• /
• pp.73-80
• /
• 2005

This paper addresses a newly proposed start-up method of the HAUSAT-2 momentum wheel. The HAUSAT-2 is a 25kg class nanosatellite which is stabilized to earth pointing by 3-axis active control method. A momentum wheel performs two functions. It provides a pitch-axis momentum bias while measuring satellite pitch and roll attitude. Pitch control is accomplished in the conventional way by driving a momentum wheel in response to pitch attitude errors. Precession control and nutation damping are provided by driving the pitch axis magnetic torquer. A momentum wheel is nominally spinning at a particular rate and changes speed. This simulation study investigates the feasibility and performance of a proposed strategy for starting-up the wheel. A proposed strategy to start-up the wheel shows that a pitch momentum wheel can be successfully started-up to its nominal speed from rest and be stabilized to nadir pointing.

• Journal of Astronomy and Space Sciences
• /
• v.23 no.2
• /
• pp.161-166
• /
• 2006

In this paper, we describe the RLG current stabilizer circuit for attitude control in the satellite. The RLG makes use of the Sagnac effect within a resonant of a HeNe laser. The difference between two discharge currents causes one of the gyro bias errors. The theoretical background and current stabilizer are introduced. It is verified that the circuit designed is applicable to the test of input voltage and temperature.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.7
• /
• pp.1429-1435
• /
• 2004

In this work, high performance broadband amplifier MMIC including all the matching and biasing components, and electrostatic discharge (ESD) protection circuit was developed for K/Ka band applications. Therefore, external biasing or matching components were not required for the operation of the MMIC. STO (SrTiO3) capacitors were employed to integrate the DC biasing components on the MMIC, and miniaturized LC parallel ESD protection circuit was integrated on MMIC, which increased ESD breakdown voltage from 10 to 300 V. A pre-matching technique and RC parallel circuit were used for the broadband design of the amplifier MMIC. The amplifier MMIC exhibited good RF performances and good stability in a wide frequency range. The chip size of the MMICs was $1.7{\pm}0.8$ mm2.