• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.1
• /
• pp.15-21
• /
• 2008

SiC has an excellent resistance to oxidation and corrosion, high temperature strength and good thermal conductivity. However, it is difficult to density because of its highly covalent bonding characteristics. Hot-press sintering process was applied to fabricate fully densified SiC ceramics with carbon and boron addition as a sintering additive. The addition of carbon improved the mechanical properties of SiC because it could induce a fine and homogeneous microstructure by the suppression of abnormal growth of SiC grain. Also, the addition of carbon could control the phase transformation of SiC. The phase transformation of 6H to 4H increased with sintering temperature but the addition of carbon decreased that kind of phase transformation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.100.2-100.2
• /
• 2015

반도체 산업이 성장하고 기술이 향상됨에 따라 소자의 소형화가 이루어지고 있다. 공정법으로는 atomic layer deposition (ALD), chemical vapor deposition (CVD) 등이 있다. 이러한 공정을 이용하여 수십 nm까지 미세화가 진행되고 있으며, 복잡한 구조의 박막을 실현하기 위해 전구체의 개발이 활발히 진행되고 있다. 전구체의 특성을 비실시간으로 분석하는 방법으로는 질량 분석법, 가스크로마토그래피, 적외선 분광법 등이 있다. 전구체의 특성을 실시간으로 분석하기 위해 Fourier transform infrared spectroscopy (FTIR)내에 attenuated total reflectance (ATR)를 거치시켰다. 본 연구는 구조를 개선한 ATR-FTIR을 이용하여 Tris-(dimethylamino) Zirconium (CpZr) 전구체의 흡착 거동을 분석하였다. ATR용 crystal은 Ge crystal을 사용했으며, 온도를 각각 30, 40, $50^{\circ}C$에서 CpZr 전구체의 흡착특성을 연구했다. 흡착성을 증가시키기 위해 Ge crystal 표면에 $ZrO_2$나노입자를 분포시켜 흡착특성을 비교 분석하였다. 또한 CpZr 전구체가 흡착된 Ge crystal 표면에 오존가스를 주입시킨 후 변화를 관찰하였다. Ge crystal표면에 나노입자를 분포시켜 CpZr 전구체를 흡착한 결과 나노입자를 분포시키지 않았을 때 보다 흡착강도가 높게 나타났다. 또한 CpZr 전구체가 흡착된 Ge crystal 표면에 오존가스를 주입한 결과 C-H 결합이 분해됨을 확인했다.

• Restorative Dentistry and Endodontics
• /
• v.29 no.5
• /
• pp.423-429
• /
• 2004

The purpose of this study was to evaluate the effect of multiple application of all-in-one dentin adhesive system on microtensile bond strength using confocal laser scanning microscope and microtensile bond strength test. Flat occlusal dentin surfaces were prepared using low-speed diamond saw. In group I, Scotchbond Multipurpose (SM) was applied by manufacturer's recommendation. In group II, after Adper Prompt L-Pop was applied for 15s and light cured for 10s. the second coat was re-applied and light-cured. In group III, after light-curing the second layer. the third coat was re-applied and light-cured. Specimens bonded with a resin-composite were sectioned into resin-dentin stick for measuring the adhesive layer thickness by confocal laser scanning microscope and evaluating micro-tensile bond strength. The adhesive layers of three-step dentin adhesive system. 3 coats of Adper Prompt L-Pop had significantly thicker than SM. 2 coats of Adper Prompt L-Pop (p < 0.05). However. there was no significant differences in bond strengths between SM and 3 coats of Adper Prompt L-Pop (p > 0.05). And SM. 3 coats of Adper Prompt L-Pop had significantly higher than 2 coats of Adper Prompt L-Pop in bond strengths (p < 0.05).

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.203-212
• /
• 1996

Applicability of SiC coating through CVD process and PCS(polycarbosilane) impregnation for the oxidation resistance and mechanical properties of C/C composite was studied. The SiC layer coated by CVD was deposited uniformly on the C/C composite, whereas the SiC converted from PCS impregnation wetted around individual carbon fiber. The PCS-impregnated C/C composite exhibited a significant increase of bending strength in comparison with as received C/C composite. This increase in the mechanical property could be attributed to the high bonding strength between fibers due to an impregnated SiC phase. The PCS-impregnated C/C showed 25% improvement in density, 3.5 times higher MOR and 2.8 times higher oxidation resistance compared to the as-received C/C. The increments due to PCS impregnation were more effective than CVD process.

• Restorative Dentistry and Endodontics
• /
• v.29 no.4
• /
• pp.339-345
• /
• 2004

The aim of this study was to measure and compare the micro shear bond strengths of the following dentin bonding systems to the dentin surfaces under simulated pulpal pressure: All Bond $2^{\circledR},{\;}Second^{\circledR},{\;}AdheSE^{\circledR}$, Adper Prompt $L-Pop^{\circledR}$. The occlusal surfaces of 180 extracted human molars were prepared so the dentin bonding surfaces could be exposed. The teeth were randomly assigned to 3 equal groups of 60 each and subdivided. The dentin surfaces were treated with the above mentioned bonding system and resin composite cylinders were built up under a simulated pulpal pressure when saline (Group II) or diluted bovine serum (Group III) was used as the pulpal fluid. As a control. the same procedures were performed in the dried dentin surfaces (Group I). After one day of storage in water. the micro shear bond strengths were measured using an EZ tester. Group II and III showed significantly lower shear bond strength than Group I statistically (p < 0.05). $SEbond^{\circledR}{\;}and{\;}AdheSE^{\circledR}$ showed no difference among the different dentin condition. In the Adper Prompt $L-Pop^{\circledR}$. a simulated pulpal pressure were applied to the specimens using diluted bovine serum. which showed a higher strength than the specimens in which saline was used (p < 0.05).

• Journal of the Korea Concrete Institute
• /
• v.27 no.2
• /
• pp.127-136
• /
• 2015

To evaluate the effects of limestone powder and silica fume on the properties of high-strength high-volume ground granulated blast-furnace slag (GGBFS) blended cement concrete, this study investigated the rheology, strength development, hydration and pozzolanic reaction characteristics, porosity and pore size distribution of high-strength mortars with the water-to-binder ratio of 20, 50 to 80% GGBFS, up to 20% limestone powder, and up to 10% silica fume. According to test results, compared with the Portland cement mixture, the high-volume GGBFS mixture had much higher flow due to the low surface friction of GGBFS particles and higher strength in the early age due to the accelerated cement hydration by increase of free water; however, because of too low water-to-binder ratio and cement content, and lack of calcium hydroxide content, the pozzolanic reactio cannot be activated and the long-term strength development was limited. Limestone powder did not affect the flowability, and also accelerate the early cement hydration. However, because its effect on the acceleration of cement hydration is not greater than that of GGBFS, and it does not have hydraulic reactivity unlikely to GGBFS, compressive strength was reduced proportional to the replacement ratio of limestone powder. Also, silica fume and very fine GGBFS lowered flow and strength by absorbing more free water required for cement hydration. Capillary porosities of GGBFS blended mortars were smaller than that of OPC mortar, but the effect of limestone powder on porosity was not noticeable, and silica fume increased porosity due to low degree of hydration. Nevertheless, it is confirmed that the addition of GGBFS and silica fume increases fine pores.

• Applied Chemistry for Engineering
• /
• v.16 no.3
• /
• pp.317-322
• /
• 2005

Nowadays, recycling of aggregates from the waste concrete is in big demand due to the protection of environment and the shortage of aggregates that are needed for ever expanding construction projects. This study was undertaken to examine the feasibility of recycling waste concrete powder produced in the crushing process of demolished concrete as a filler material for polymer mortar. In this study, polymer mortar specimens were prepared by varying the mix proportion of polymer binder (ranging 9~15 wt%), waste concrete powder (ranging 0~20 wt%) substituted for silica powder, 0.1~0.3 mm fine aggregate (ranging 21~24 wt%) and 0.7~1.2 mm fine aggregate (ranging 44~47 wt%). For the prepared polymer mortar specimens, various physical properties such as strength, water absorption, heat water resistance, acid resistance, pore distribution and SEM observation were investigated in this work. As a result, physical properties of polymer mortar were observed to have remarkably improved with an increase of polymer binder, but greatly deteriorated with an increase of substitution quantity of waste concrete powder.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.2
• /
• pp.61-70
• /
• 1996

침엽수재(針葉樹材)(Radiata pine, Pinus radiata)MDF와 활엽수재(闊葉樹材)(Rubber wood, Hevea brasiliensis)MDF 각 1종을 대상으로 MDF를 제조하기 전 원료(原料) 섬유(纖維)의 미세(微細) 구조(構造) 및 내부결합력 시험 후 MDF의 파괴면(破壞面)에서 섬유표면(纖維表面)에 접착제(接着劑)가 도포(塗布)된 형태를 주사전자현미경(走査電子顯微鏡)으로 관찰하였다. 원료 섬유는 침(針) 활엽수재(闊葉樹材) 모두 fiber twisting 및 shrinkage fold 등이 관찰되었다. 침엽수재(針葉樹材)의 경우는 유연벽공부(有緣壁孔部)에서 유연벽공(有緣壁孔)이 없는 부분에 비하여 shrinkage fold의 발생 빈도가 낮고 표면(表面) 박리(剝離)는 가도관(假導管) 중 벽공이 없는 부분에서 관찰되었다. 활엽수재(闊葉樹材) 목섬유(木纖維)는 침엽수재(針葉樹材)와 마찬가지로 shrinkage fold가 관찰되었으나 표면(表面) 박리(剝離)는 거의 관찰되지 않았다. 활엽수(闊葉樹) 섬유(纖維)에서는 벽공의 유무에 따른 shrinkage fold의 차이(差異)가 거의 관찰되지 않았는데 이는 목섬유(木纖維)가 침엽수(針葉樹) 가도관(假導管)보다 작은 단벽공(單壁孔)을 갖기 때문으로 생각된다. 또 방사유세포(放射柔細胞)와 가도관(假導管) 및 목섬유(木纖維)의 박리(剝離) 부분(部分)에는 융기부(隆起部)가 관찰되었다. 내부결합력 시험후 나타난 파괴면을 통하여 접착제 분포를 관찰한 결과 거의 모든 섬유(纖維)들이 접착제(接着劑)로 둘러싸여 있었으며 섬유(纖維)간 접착형태(接着形態)도 매우 다양하였다. 침활엽수재(針闊葉樹材)간에 강도(强度)의 차이는 있었지만 파괴(破壞) 형태(形態)는 큰 차이를 나타내지 않았다. 즉 침활엽수(針闊葉樹) 모두 접착층(接着層)이 아닌 섬유(纖維)에서 파괴(破壞)가 발생하였으며 섬유에서 박리(剝離)된, 세포벽(細胞壁)의 일부가 다른 섬유(纖維)의 표면(表面)에 남아있는 형태와 섬유(纖維) 표면(表面)에서 떨어져 나간 형태로 관찰되었다. 세포 구성이 단순한 침엽수(針葉樹) MDF에 비하여 유세포(柔細胞)와 도관(導管) 및 목섬유(木纖維)의 파편들이 활엽수(闊葉樹) MDF에서는 다양(多樣)하게 분포하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.306-306
• /
• 2007

최근, LED 구동 인버터, DC-DC 컨버터, AC-DC 컨버터 및 형광등 ballaster 등의 고전압전원장치등에 압전변압기를 적용하고자 하는 연구가 활발히 진행되고 있다. 순수한 $PbTiO_3$는 큐리온도($490^{\circ}C$)가 높고, 기계적강도가 크며, 비유전율(약 200 정도)이 작다. 또한, 두께방향 진동의 전기기계 결합계수 ($K_t$)가 윤곽진동의 전기기계 결합계수($K_p$)보다 크므로 두께방향의 진동모드를 이용한 벌크파 진동자의 경우 윤곽진동방향으로 불요신호(spurious signal)가 적고, 작은 grain size($1\;{\mu}m$정도)로 미세가공이 가능하여 고주파 재료로 이용되고 있다. 압전변압기의 출력 전력을 향상시키기 위해서는 적층으로 제작하여야 하는데 적층 압전변압기 제작시 층간의 내부 전극이 도포된 상태에서 소결하여야 한다. 이때 소걸 온도가 높으면 Pd 함랑이 높은 전극을 사용하여야 하는데 Pd 전극의 가격이 비싸 소자의 경제성이 떨어지게 된다. 따라서 순수한 Ag 전극을 내부전극으로 사용하기 위해서는 $900^{\circ}C$ 이하에서 소결이 가능하여야 한다. 따라서 본 연구에서는 $(Pb,Ca,Sr)Ti(Mn,Sb)O_3$ 조성을 이용하여 $900^{\circ}C$ 이하의 저온소결이 가능한 두께방향진동모드 적층 압전변암기를 제작하여 그에 대한 전기적 특성을 조사하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.2
• /
• pp.90-97
• /
• 2018

The quantities of electronic waste have been increased rapidly, and was caused variety problems such as environmental pollution or dissipation of resource. So, it needed to development of recycling technology about heavy metal in the electronic waste. Meanwhile, filler material (concrete or mortar) was used for shielding radioactive waste, however, it did not used materials that it is proved radiation shielding performance. So, there is a lack of confidence in the shielding performance. Therefore, in this paper, mechanical properties of concrete was evaluated for the applicability using electronic waste as fine aggregate of filler material. From the test results, compressive and flexural strength and elasticity modulus and the micro pore in the $1{\mu}m$ range was significantly affected by substitution of electronic waste, however, it could be improved the performance by using mineral admixture as binder. So, it is shown that the electronic waste could be applicable as fine aggregate of filler material.