• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.05a
• /
• pp.535-538
• /
• 2009

Auto Pilot is the system which move automatically the vessel through locating operation mode to automatic after entering operating course using a electronic chart or plotter. And water jet is the a propulsion system that make a power to push the vessel through spouting the accelerated water which is absolbed by the hole in the bottom of vessel. The water jet receive the effect of the depth of water lowly, it's acceletion efficiency is higher under high speed and have an advantage on vibrating and floating sound, so it's demand is increasing as new propulsion system. However, the signal systems of auto Pilot and water jet are defferant, we need the system to communicate between each system. We propose the interface system which communicate between Auto pilot and water jet efficiently in this journal.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.2
• /
• pp.9-21
• /
• 1999

The waterjet is very widely used today in propulsion system of high speed vessel but manufacturer is limited because of an efficiency and a difficulty of a manufacture on the inlet configuration of the waterjet. The importancy in designing the inlet configuration of the waterjet lies on the minimization of the cavitation which is largely affecting the efficiency. In this paper, the configuration analysis is carried out to find a optimum shape which is minimizing the cavitation using a two dimensional potential-based panel method with an inlet configuration of a flush type. Also, it is developed a direct design method finding an inlet configuration by a given pressure distributions. The numerically obtained optimum shape using this configuration analysis method show a good agreement compared to the Kashiwadani's results. It is carried out a direct design method over a lip and a ramp of an inlet configuration wish pressure distributions obtained a result of the configuration analysis and the results show a good agreement compared to original configuration.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.3
• /
• pp.197-204
• /
• 2005

A waterjet propulsion system has many advantages compared with a conventional screw propeller especially for amphibious armored wheeled vehicles because of a good maneuverability at low speed, good operation ability at shallow water, high thrust at low speed to aid maneuverability and exit from water, etc. The POD type waterjet is adequate for the present wheeled vehicle because the weight is lighter and L/B is longer than the conventional armored amphibious vehicle. Resistance and self-propulsion tests with a 1/3.5-scale model are conducted at PNU towing tank. Based on these measurements, the performance is analyzed according to ITTC 96 standard analysis method and also according to the conventional propulsive factor analysis method. Based on these two methods, the full-scale effective and delivered powers of amphibious armored wheeled vehicle are estimated. This paper emphasizes the analysis method of model test of the waterjet propulsion system for a amphibious armored wheeled vehicle and the model test technique together with the comparison of the two analysis methods.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.4
• /
• pp.31-41
• /
• 1997

This paper describes a potential-based panel method formulated for the prediction of the steady performance of a waterjet propulsor. The method employs normal dipoles and sources distributed on the solid surfaces such as the impeller/stator blades, hub and duct, and normal dipoles in the shed wakes trailing the impeller and stator to represent the potential flow around the waterjet propulsor. To define a closed boundary surface, the inlet and outlet open boundary surfaces are introduced where the sources and dipoles are distributed. The kinematic boundary condition on the solid boundary surface is satisfied by requiring that the normal component of the total velocity should vanish. On the inlet surface, the total inflow flux into the duct is specified, and on the outlet surface the conservation of mass principle is applied to evaluate the source strength. The solid surfaces are discretized into a set of quadrilateral panel elements and the strengths of sources and dipoles are assumed constant at each panel. Applying this approximation to the boundary conditions leads to a set of simultaneous equations. Systematic numerical tests show that the present numerical method is fast and stable. In order to validate the present method, sample computations are carried out first for the case of a conventional axial flow fan which has a similar geometry as the waterjet propulsor, and then for the case of a waterjet propulsor on which experiments are carried out at KRISO(Korea Research Institute of Ships and Ocean Engineering).

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.4
• /
• pp.48-54
• /
• 2005

An experimental study was carried out to investigate the effect of film cooling in the lab-scale liquid rocket engine using liquid oxygen(LOx) and Jet A-1(Jet engine fuel) as propellants. Film coolants(Jet A-1 and water) was injected through the film cooling injector. The outside wall temperature of the combustor and film cooled length were determined for chamber pressure, mixture ratio, and the different geometries(injection angle) with the percent film coolant flow rate. The loss of characteristic velocity was determined for the case of film cooling with water and Jet A-1. As chamber pressure increased, the outside wall temperature increased in the nozzle but unchanged over the 9 percent film coolant flow rate for the combustion chamber used in this study. Characteristic velocity wasn't affected with the mixture ratio over the 9 percent film coolant flow rate.

• Journal of Korea Ship Safrty Technology Authority
• /
• v.17
• /
• pp.24-43
• /
• 2005

최근 우리나라 어선어업은 한중일 어업협정, 연안 어업자원 감소 및 연안오염 등 사회적, 환경적 변화가 급변하고 있어 이들을 고려한 어선 선형개발이 필요로 한다. 현재 우리나라의 어선 중 연안지역에서 조업하는 5톤 미만의 소형어선은 전체 어선 중 $65\%$ 이상으로 구성되어 있으나 선박의 크기가 작고 부가가치가 낮은 관계로 지금까지 전문적인 연구는 거의 없었던 것이 현실이다. 한편, 서$\cdot$남해 연안에서 작업 및 항해하는 연안어선들의 해양사고 발생율은 전체사고의 $69.6\%$로 매년 증가하고 있는 추세이다. 전체 어선 안전사고 중 부유폐어망, 로프 등이 추진기에 감긴 사고는 전체 사고의 $10.4\%$로 매년 증가하고 있다. 이에, 추진기 손상에 의한 어선 사고와 연관하여 추진기를 보호하기 위한 장치로서 물분사 추진기(Water-Jet), 펌프제트(Pump-Jet)장치들이 있으나 이들은 고가 수입품으로서 영세한 어민들의 소형어선에 장착하기에는 한계가 있어, 본 연구에서는 폐그물, 로프 등 해상 부유물에 의한 추진기 손상이 발생되지 않는 프로펠러 보호터널 부착 추진장치를 개발을 목적으로 한다. 프로펠러 부착 추진장치는 기존 선미를 수정하여 추진기를 선체 안쪽으로 배치하며 돌출되는 부분은 덕트로 보호하고 있으며 이러한 추진기는 워터제트 추진기와는 달리 가격이 싸고 그물이나 부유물에 걸리지 않고 고장 시 신속한 대응이 쉬워 소형 연안어선에 적합할 뿐만 아니라 그물, 부유물, 갯벌이 많은 국내의 서$\cdot$남해 연안에서 작업 및 항해 시 매우 유용할 것으로 판단된다. 본 연구는 `프로펠러 보호터널 부착 연안어선의 선형개발`을 최종목표로 수행하였으며, 연구개발 내용은 기존 소형 연안어선의 분류 및 특성 조사 연구, 프로펠러 보호터널형 선미 선형 개발, 기존 선형 및 보호터널형 선형의 모형시험, 개발선의 구조강도 특성, 프로펠러 설계 및 단독시험, 보호터널 부착 추진기의 효율 검증 및 개발 대상 어선의 조선공학적 제 계산, 설계도작성 등을 실시하였다. 주요 요소 기술로서는 프로펠러 보호터널 부착 선형의 모형시험을 통하여 선미선형을 개발하며 FRP판부재의 구조강도 특성을 분석하고 그 결과를 활용하여 4톤급 연안어선의 시제선을 건조하고 시운전을 통하여 주요성능을 확인하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.139-143
• /
• 2005

Combustion Test Facility for Liquid Rocket Engine using kerosene and liquid oxygen has been developed for the purpose of cooling and performance study. Test engine of thrust 0.5 KN(design thrust) is tested to confirm the normal operation. Therefore, water-cooled firing tests using kerosene engine with injectors of fuel-centered coaxial type are conducted. With the viewpoint of characteristic velocity, and specific impulse at sea level, and chamber pressure on OF mixture ratio are analyzed.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.2
• /
• pp.178-187
• /
• 2010

The performance of the waterjet system of a patrol boat has been experimentally studied. A waterjet propulsion system has many advantages comparing with a conventional screw propeller especially for high speed craft because of its good cavitation performance. This paper describes experimental procedure and analysis method of self-propulsion tests with a 1/12-scale model. Experimental results were analyzed according to ITTC 96 standard method. The full-scale effective power and delivered power of the ship were also analyzed and the full-scale speed predicted from the model test compares reasonably with the measured full-scale results of the sea trial.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.2
• /
• pp.127-135
• /
• 2009

The performance of the waterjet system of 180 ton class fishing guard ship has been experimentally studied. A waterjet propulsion system has many advantages in comparison with a conventional screw propeller especially for high speed craft because of its good cavitation performance. Recently waterjet system has been applied to fishing boats and fishing guard ship because of avoiding a net problem although their speeds are not so high. This paper describes experimental procedure and analysis method of resistance and self-propulsion tests with a 1/14.46-scale model. Experimental results were analyzed according to ITTC 96 standard method. The full-scale effective power and delivered power of the ship were also analyzed and the full-scale speed predicted from the model test results shows a good agreement with the full-scale result from the sea trial tests.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.1
• /
• pp.9-14
• /
• 1999

The effect of operating condition was studied experimently on the characteristics of twin sprays ejected from two airblast atomizers, within the range of the mass air-fuel ratio 1.36∼3.54. Water and nitrogen gas were used as test fluids for the experiments. Spray characteristics of liquid spray were measured with measurement of mass distribution and instantaneous image of the spray cone. Experimental results show that the maximum specify of the distribution were lowered but distributed over the larger area when the ROA ratio increased, Center of mass position did not change with increasing water mass flow, Increase of the nozzle distance has an small effect on mass distribution of interaction area but distributed over the larger area. It was also conformed that the effect of interaction near central point of collision decreased with the increase of the ROA ratio on interaction area from comparison using superposition method