• Journal of the Korean Electrochemical Society
• /
• v.3 no.4
• /
• pp.191-195
• /
• 2000

Electrochemical properties of the oxygen electrode in phosphoric acid fuel cell have been studied using AC impedance method as a function of applied potential, operating temperature and teflon content in the electrode. The oxygen electrode reaction in the $105wt.\%$ phosphoric acid is characterized by a parallel resistive component, $R_p$ and a capacitive component, $C_p$ with serial electrolyte resistance, $R_s$. The conductivity of the phosphoric acid is found to be 0.31-0.47 S/cm in the range of $130\;to\;190^{\circ}C$ from the measured impedance. The increase of applied potential and temperature produced the decreased RP and the increased $C_p$, which means the increase of the oxygen electrode reaction rate. The single cells with the cathode of various teflon contents were tested, and the cathode with $40wt.\%$ teflon showed good performance, which is considered to be related to an optimized impedance behavior.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.10
• /
• pp.917-923
• /
• 2010

Direct numerical simulation (DNS) of a spatially developing turbulent boundary layer (TBL) with regularly arrayed cubical roughness elements was performed to investigate the effects of three-dimensional (3D) surface elements. The staggered cubes downstream were periodically arranged in the streamwise and spanwise directions with pitches of $p_x$/k=8 and $p_z$/k=2, where $p_x$ and $p_z$ are the streamwise and spanwise spacings of the cubes; the roughness height (k) was k=$1.5{\theta}_{in}$, where ${\theta}_{in}$ is the momentum thickness at the inlet. Spatially developing characteristics over the 3D cubical roughness were compared with the data obtained from the DNS over the two-dimensional (2D) rod roughened wall and smooth wall. Introduction of the cubical roughness on the TBL affected the turbulent Reynolds stresses not only in the roughness sublayer but also in the outer layer; and these effects are consistent with those observed over the 2D rough wall.

• Journal of Wetlands Research
• /
• v.21 no.4
• /
• pp.281-289
• /
• 2019

In this study, the typhoon damage forecasting model was developed for southern inland district. The typhoon damage in the inland district is caused by heavy rain and strong winds, variables are many and varied, but the damage data of the inland district are not enough to develop the model. The hydrological data related to the typhoon damage were hour maximum rainfall amount which is accumulated 3 hour interval, the total rainfall amount, the 1-5 day anticipated rainfall amount, the maximum wind speed and the typhoon center pressure at latitude 33° near the Jeju island. The Multivariate Analysis such as cluster Analysis considering the lack of damage data and principal component analysis removing multi-collinearity of rainfall data are adopted for the damage forecasting model. As a result of applying the developed model, typhoon damage estimated and observed values were up to 2.2 times. this is caused it is difficult to estimate the damage caused by strong winds and it is assumed that the local rainfall characteristics are not considered properly measured by 69 ASOS.

• Korean Journal of Materials Research
• /
• v.11 no.3
• /
• pp.203-206
• /
• 2001

The effects of SrTiO$_3$ addition and sintering temperature on the microstructure and magnetic properties of yttrium iron garnet (YIG) were investigated. The lattice Parameter increasing of sintered YlG with small amount of SrTiO$_3$ addition was supposed to be substituted $Y^{+3}$, Fe$^{+3}$ ions to Sr$^{+2}$,Ti$^{+4}$ ions which are relatively large in ionic ranius. A YIG specimen sintered at 142$0^{\circ}C$ with 0.2mol% SrTiO$_3$ showed above 98% densification of theoretical density. Saturation magnetization (M$_s$) at room temperature decreased a little bit with increasing SrTiO$_3$, addition but no great chance. In addition, the coercivity (H$_c$) was almost not changed by sintering temperature.

• Resources Recycling
• /
• v.22 no.3
• /
• pp.50-56
• /
• 2013

Recycled plastic composites of ABS/PE (50/50 and 20/80) and ABS/GF (90/10) were fabricated from plastic components of waste LCDs and effects of PE composition on elongation of ABS/PE composites were investigated. Increased PE contents improved elongation of the composite from 2.4% to 13%, which was attributed to increased crystalline behavior of the ABS/PE composite afforded by ductile PE fraction: SEM fractographs showed some sign of plastic deformation of PE matrix before ductile fracture of the composites.

• Applied Chemistry for Engineering
• /
• v.16 no.2
• /
• pp.238-242
• /
• 2005

In this work, Polydimethylsiloxane (PDMS) and SU-8 (Microchem, USA) photoresist were used to make the microchannel by soft lithographic method. To investigate the effects of external voltages and widths of the microchannel, we made the microchannel by soft lithographic method. To investigate the effects of external voltages and widths of the microchannel, we made the microchannel with various widths: $100{\mu}m,\;200{\mu}m$ and $300{\mu}m$. And each micorchannel was supplied with external voltage, respectively. As a result, the fluid velocity increased with an increase of the external voltage at the same width. It was speculated that the electrical double layer was condensed and the zeta potential increased with increase of the external voltage. The fluid velocity increased with the microchannel width increase at the same external voltage. It is concluded that the resistance in the microchannel decreased as the microchannel width increased.

• Applied Chemistry for Engineering
• /
• v.25 no.1
• /
• pp.47-52
• /
• 2014

A series of liquid crystalline polyesters containing X-shaped mesogenic groups in main chain were synthesized through the solution polymerization of 2,5-di(4-substituted benzoate)hydroquinones and 4,4'-dicarboxy-1,8-diphenoxyoctane. The structures and properties of synthesized polymers were investigated by $^1H$-NMR, FT-IR, differential scanning calorimetry (DSC), thermogravimetry analysis (TGA), polarized optical microscopy (POM) and wide angel X-ray diffraction (WXRD). Inherent viscosities (${\eta}_{inh}$) of polymers were measured between 0.35 and 0.66 dL/g in 1,1,2,2-tetrachloroethane, and they were easily soluble in most of organic solvents used for this experiment. All polymers revealed relatively low melting transition temperature ($T_m$) and crystallinity, and also showed thermotropic nematic liquid crystallinity when they were heated to their melting temperatures. These properties of polymers were presumably due to the presence of the bulky substituting groups on the hydroquinone unit in mesogenic group.

• Applied Chemistry for Engineering
• /
• v.25 no.3
• /
• pp.268-273
• /
• 2014

In this study, multi-walled carbon nanotubes (MWCNT) were treated with nickel by electroless plating method for improving electromagnetic interference (EMI) shielding performance of MWCNT. The physical properties of electroless plated MWCNT were analyzed by using ultra-high resolution scanning electron microscope (UHR-SEM), thermogravimetry (TGA), sheet resistance analyzer and EMI shielding analyzer. EMI shielding efficiencies of nickel electroless plated MWCNT were measured to be 16 dB from 800 MHz band, which was 1.6 times increased compared to that of the activated MWCNT. Also, the average sheet resistance of nickel electroless plated MWCNT was measured to be $70{\Omega}/sq$, which was 56% decreased compared to that of the activated MWCNT. This result could be attributed to the plating morphology on the surface of MWCNT. This result could be attributed to uniformity of plating morphology on the surface, which has more effect on EMI shielding efficiency than the amount of nickel plating.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.2
• /
• pp.158-165
• /
• 2019

The purpose of this study is to investigate analytically the flexural behavior of beam reinforced by an alkali-activated slag-based fiber-reinforced composite. The materials and mixture proportion were selected to manufacture an alkali-activated slag-based fiber-reinforced composite with high tensile strain capacity over 7% and compressive strength and tension tests were performed. The composite showed a compressive strength of 32.7MPa, a tensile strength of 8.43MPa, and a tensile strain capacity of 7.52%. In order to analyze the flexural behavior of beams reinforced by ultra-high-ductile composite, nonlinear sectional analysis was peformed for four types of beams. Analysis showed that the flexural strength of beam reinforced partially by ultra-high-ductile composite increased by 8.0%, and the flexural strength of beam reinforced fully by ultra-high-ductile composite increased by 24.7%. It was found that the main reason of low improvement in flexural strength is the low tensile strain at the bottom of beam. The tensile strain at bottom corresponding to the flexural strength was 1.38% which was 18.4% of tensile strain capacity of the composite.

• Membrane Journal
• /
• v.33 no.2
• /
• pp.61-69
• /
• 2023

The technical importance of membrane-based artificial lung technology has been re-emphasized after the recent breakout of COVID-19 to treat acute lung-failure patients. The world population, particularly in Korea, is aging at an unprecedented rate, which can increase the demand for better artificial organs (AO) in the near future. Membrane technology plays a key role in artificial organ markets. Among them, membrane-based artificial lung (AL) technology has improved significantly in the past 50 years, but the survival rate of lung-failure patients is still very low. Most AL works focus on the clinical application of the AL device, not on the development of the AL membrane itself. This review summarizes the challenges and recent progress of membrane-based AL technology.