• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.9
• /
• pp.831-837
• /
• 2015

Many persons and electronic devices are exposed to electromagnetic (EM) waves generated from magnetic resonance imaging (MRI) equipment, EM pulses (EMPs), and many other kinds of EM wave devices. Finger strips are used to provide shielding from these EM waves. Because of the high thermal conductivity of finger strips, they are used in the design of specialized doors that are installed in shielded rooms. In this study, we perform an accelerated life test using the load acceleration stress, which affects the main failure mode of finger strips. We predict the life of the finger strip under normal usage conditions based on the results of the accelerated life test. We compare the results with those predicted from the life test under normal usage conditions to evaluate the validity of accelerated life testing.

• Journal of Broadcast Engineering
• /
• v.19 no.3
• /
• pp.355-361
• /
• 2014

In this paper, we propose a complexity reduction method of sample adaptive offset (SAO), which is an in-loop filter in high-efficiency video coding (HEVC). In the conventional SAO, an offset value is calculated for each coding tree block (CTB) to minimize the error between the original and reconstructed images. In order to determine the optimal offset value, all offset candidates are examined and the offset value that leads to the smallest rate-distortion cost is chosen. Thus, SAO occupies a significant amount of the computational complexity in the HEVC encoder. In the proposed method, we determine the least-used band (LUB) by considering the statistical characteristics of offset values and without processing the offset value included in the LUB. Also, in the offset value decision stage, we check only a certain number of candidates rather than all of them. Experimental results show that the proposed method reduces the encoding time by approximately 8.15% without yielding a significant loss in terms of coding efficiency.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.991-997
• /
• 2004

In this paper, we propose the architecture of modem receiver to fabricate HomePNA 2.0 chip. HomePNA suffers from inferior channel because of bridge tap, the effect of amateur HAM band and so on. To transfer data over such channel, HomePNA 2.0 uses training sequence to equalize channel and uses FD-QAM optionally as modulation method. So modem receiver demodulate QAM based signal and needs optimum architecture that fully uses these transmission feature. As a result of research, we define 2 mode function of modem receiver depending on TX/RX state. In this paper, particularly, we show the algorithm of equalizer, carrier phase recovery and frame synchromzationblock and propose architecture that improve the performance of channel equalization and is stable in operation. In the end, we estimate the performance of proposed HomePNA2.0 modem receiver over HomePNA TEST LOOP using SPW program.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.15-20
• /
• 2016

The existing multiple modulus-based self-recovering equalization type has not been applied to initial equalization. Instead, it was used for steady-state performance improvement. In this paper, for the self-recovering equalization type that considers the multiple modulus as a desired response, the initial convergence performance was improved by extending the dynamics of the errors using error boosting and their characteristics were analyzed. Error boosting in the proposed method was carried out in proportion to a symbol decision for the equalizer output. Furthermore, having the initial convergence capability by extending the dynamics of errors, it showed excellent performance in the initial convergence rate and steady-state error level. In particular, the proposed method can be applied to the entire process of equalization through a single algorithm; the existing methods of switching over or the selection of other operation modes, such as concurrent operating with other algorithms, are not necessary. The usefulness of the proposed method was verified by simulations performed under the channel conditions with multipath propagation and additional noise, and for performance analysis of self-recovering equalization for high-order signal constellations.

• Smart Media Journal
• /
• v.13 no.5
• /
• pp.45-51
• /
• 2024

Recently, realistic contents such as virtual reality(VR) and augmented reality (AR) are widely used for education to provide beneficial learning environments with thee-dimensional(3D) information and interactive technology. Specially, AR technology will be helpful to intuitively understand by adding virtual objects registered in the real learning environment with effective ways. In this paper, we developed an AR learning system using 3D spatial information in the 2D based textbook for studying math related to geometry. In order to increase spatial learning effect, we applied to solid shapes such as prisms and pyramids in mathematics education process. Also, it allows participants to use various shapes and expression methods (e.g., wireframe mode) with interaction. We conducted the experiment with our AR system, evaluated achievement and interest. Our experimental study showed positive results, our results are expected to provide effective learning methods in various classes through realistic visualization and interaction methods.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.651-659
• /
• 2010

In this paper, a new six-port direct conversion receiver for high-speed multi-band multi-mode wireless communication system such as software defined radio(SDR) is proposed. The designed receiver is composed of two CMOS four-port BPSK receivers and a dual-band one-stage polyphase filter for quadrature LO signal generation. The four-port BPSK receiver, implemented in 0.18 ${\mu}m$ CMOS technology for the first time in microwave-band, is composed of two active combiners, an active balun, two power detector, and an analog decoder. The proposed polyphase filter adopt type-I architecture, one-stage for reduction of the local oscillator power loss, and LC resonance structure instead of using capacitor for dual-band operation. In order to extent the operation RF bandwidth of the proposed six-port receiver, we include I/Q phase and amplitude calibration scheme in the six-port junction and the power detector. The calibration range of the phase and amplitude mismatch in the proposed calibration scheme is 8 degree and 14 dB, respectively. The validity of the designed six-port receiver is successfully demonstrated by modulating M-QAM, and M-PSK signal with 40 Msps in the two-band of 900 MHz and 2.4 GHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.10
• /
• pp.45-52
• /
• 2008

We investigated the design of an RF-powered, wireless temperature sensor tag chip using $0.18-{\mu}m$ CMOS technology. The transponder generates its own power supply from small incident RF signal using Schottky diodes in voltage multiplier. Ambient temperature is measured using a new low-power temperature-to-voltage converter, and an 8-bit single-slope ADC converts the measured voltage to digital data. ASK demodulator and digital control are combined to identify unique transponder (ID) sent by base station for multi-transponder applications. The measurement of the temperature sensor tag chip showed a resolution of $0.64^{\circ}C/LSB$ in the range from $20^{\circ}C$ to $100^{\circ}C$, which is suitable for environmental temperature monitoring. The chip size is $1.1{\times}0.34mm^2$, and operates at clock frequency of 100 kHz while consuming $64{\mu}W$ power. The temperature sensor required a -11 dBm RF input power, supported a conversion rate of 12.5 k-samples/sec, and a maximum error of $0.5^{\circ}C$.

• Analytical Science and Technology
• /
• v.25 no.1
• /
• pp.25-32
• /
• 2012

Isotope dilution mass spectrometry (ID-MS) based on liquid chromatography tandem mass spectrometry (LC/MS/MS) was developed for the accurate determination of sorbic acid in tea-drink. An isotope analogue of sorbic acid, $^{13}C_2$-sorbic acid, was obtained by custom synthesis. MS was operated in the negative mode with selected reaction monitoring (SRM) mode of $[M-H]^-$ ${\rightarrow}$ $[M-CO_2H]^-$ channel at m/z 111 ${\rightarrow}$ 67 for sorbic acid and at m/z 113 ${\rightarrow}$ 68 for its isotope analogue. Chromatographic separation was accomplished with a C18 column and an isocratic mobile phase of 55% of 50 mM ammonium acetate (pH 4.5) and 45% of methanol. Homogeneous reference materials were prepared for validation of this method, including repeatability and reproducibility tests, by fortifying tea-drink with sorbic acid in our laboratory. Repeatability and reproducibility studies showed that the ID-LC/MS method is a reliable and reproducible method which provides less than 3.8% of relative standard deviation (RSD) for the analysis of sorbic acid.

• Analytical Science and Technology
• /
• v.23 no.6
• /
• pp.524-530
• /
• 2010

Chloramphenicol is one of the most effective antibiotics for treatment of food-producing animals for typhoid fever. However, it has been reported that it caused severe side effects such as aplastic anemia in human, therefore the use of chloramphenicol for food-producing animal is prohibited by European Union and other countries. In this study, the analytical method using isotope dilution liquid chromatography-mass spectrometry (ID-LC/MS) was established for accurate determination of chloramphenicol in meat. Chloramphenicol was extracted with ethylacetate from porcine and solid phase extraction cartridge was used for enhancing the recovery. The residue of chloramphenicol in porcine was analyzed using the liquid chromatography mass spectrometer (LC/MS) interfaced with electrospray ionization source. Analysis was performed in negative mode with selected reaction mornitoring mode at m/z 321${\rightarrow}$257 of $[M-H]^-$ ${\rightarrow}$ $[M-H-(HCOCl)]^-$ and m/z 326 ${\rightarrow}$ 262 channels for its isotope. The established method was tested using fortified samples at the level of 0.2 1, 10, $25\;{\mu}g$/kg and analytical results agreed with the gravimetrically fortified values within their uncertainties. This method was validated by analyzing a certified reference material, BCR 445, from IRMM (Institute for Reference Materials and Measurement). Our measurement values agreed with the certified value within their uncertainties. The uncertainty of our measured value was much lower than that the certified value from IRMM.

• Korean Journal of Remote Sensing
• /
• v.24 no.4
• /
• pp.351-358
• /
• 2008

KOMPSAT-5 will be launched in 2010 carrying a SAR (Synthetic Aperture Radar) system to obtain high resolution images of the earth surface regardless of weather or solar condition. In this paper, the orbits of KOMPSAT-5 and the imaging modes of SAR were analyzed for radargrammetry, and the best image pairs were suggested. We set the pass number from the nearest orbit to a given ground point and selected image pairs for radargrarnmetry, with height sensitivity of parallax higher than 0.5 to achieve enough height resolution and with the value lower than 0.8 to avoid errors from geometric distortion. On the equator, for example, where the distance between two adjacent passes is fixed to 95 km, we solved the orbit geometry and found that the image pairs with the pass numbers of 3-2 and 5-3 are suitable for radargrarnmetry. As the examples with arbitrary latitude, we selected Daejeon and Sejong Antarctic stations and calculated the orbital elements by using STK software. Three image pairs (5-4, 7-5 and 8-5) were found suitable for radargrammetry at Daejeon while 10 pairs (8-6, 9-7, 10-7, 11-8, 12-8, 13-9, 14-9, 15-9, 15-10 and 15-11) at Sejong Antarctic station.