• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.1079-1084
• /
• 2003

A liquid storage rectangular tank structures are used in many fields of civil, mechanical and marine engineering. Especially, Ship structures have many tanks in contact with inner or outer fluid, like ballast, fuel and cargo tanks. Fatigue damages are sometimes observed in these tanks which seem to be caused by resonance with exciting force of engine and propeller. Vibration characteristics of these thin walled tanks ill contact with fluid near engine or propeller are strongly affected by added mass of containing fluid. Therefore it is essentially important to estimate the added mass effect to predict vibration of the tank structures. In the previous report, we have developed numerical tool of vibration analysis of 3-dimensional tank structure using finite elements for plates and boundary elements for fluid region. In the present report, using the numerical analysis, vibrations characteristics in deep water tank are investigated and discussed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.63-66
• /
• 2005

Six RC pier were tested under a constant axial load and a cyclically reversed horizontal load to investigate the performance of RC piers used in the high strength concrete and the high strength rebar. It is designed with a hollow section according to the Korean Bridge Design Standard. The variables of the test were concrete strength, rebar strength, a ratio of lap splice and a ratio of transvere rebar. The test results show that the performance of a RC Pier; failure mode, crack pattern, maximum load and ductility.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.6
• /
• pp.896-906
• /
• 1997

The effect of duplicate flexible disks on the vibrational modes of a flexible rotor system is investigated by using an anlytical method based on the assumed modes method. The rotor model to be analyzed consists of duplicate disks on a flexible shaft. In modeling the system, centrifugal stiffening and disk flexibility effects are taken into account. To demonstrate the effectiveness of the method, a hard disk drive spindle system commonly used in personal computers and a simple flexible rotor system with two disks are selected as examples. In particular, the dynamic coupling between the vibrational modes of the shaft and the duplicate disks is investigated with the shaft rotational speed varied.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.5
• /
• pp.40-45
• /
• 2003

Optical and electronic industries are using lapping and polishing processing as a final finish rather than grinding, because they need more accurate parts of brittles non-metallic materials such as single crystals. Sapphire has been ground by the ultra-precision surface grinder having a glass -ceramic spindle of extremely-low thermal expansion with various cup-type resinoid-bonded diamond wheels of #400-#3000 in grain size. Sapphire can be ground in the ductile mode. And also, the surface roughness and grinding conditions has been clarified. The smooth surface of Sapphire less than 1nm RMS, 1nm Ra can be obtained by the ultra-precision grinding without any polishing process.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.1
• /
• pp.85-89
• /
• 2012

Conventional grinding of BK7 glass will normally result in brittle fracture at the surface, generating severe sub-surface damage and poor surface finish. The precision grinding of BK7 glass in parallel grinding modes has been investigated. Grinding process, maximum chip thickness, ductile/brittle regime, surface roughness and sub-surface damage have been addressed. Special attention has been given to the condition for generating a ductile mode response on the ground surface. Experiments reveal that the level of surface roughness and depth of sub-surface damage vary differently for different condition. This study gives an indication of the strategy to follow to achieve high quality ground surfaces on brittle materials.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.184-187
• /
• 2005

The blade is an important part of rotating turbomachinery. The blade dynamic strength is of considerable importance as far as the reliability of operation and the life of the engine ate concerned. In this paper, blades are attached to a disk and coupled by means of damping wire. We assumes that the interfaces between the blade and disk dovetails are joined together, which means surface-to-surface contacts without friction. The damping wire is implemented using a beam element and temperature effect in the blade is neglected. Centrifugal forces ale applied by using an angular velocity to all elements in the system. The FEM results showed vibration characteristics in the blade disk system for the cases of a free-standing blade and blades with damping wire, respectively.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.176-181
• /
• 2000

Acoustic modal characteristics are investigated on the passenger compartment and trunk coupled system. One-dimensional theoretical model is proposed and the validity of the model is verified by experiment on a simplified compartment model. The theoretical model identifies the occurrence of a new low frequency compartment mode, which does not exist in the uncoupled passenger compartment. The effect of the hole size on the compartment modes is analytically and experimentally examined.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.4
• /
• pp.1-8
• /
• 2008

RC beam of existing structures often encounter shear problems for various reasons. The shear failure of RC beam is sudden and brittle. Strengthening technique jacketing with external bonding of steel plates(or CFRP and CFS) with epoxy is many use to in practice. This study presents test results on strengthening shear deficient RC beams by external bonding of slit type steel plates. Test parameters are width, interval, length, thickness and angle of slit in steel plates. The purpose was to evaluate the reinforcing effects, failure modes and shear capacities for RC beams of strengthened with various slit type steel plates. The test result confirmed that all slit steel plates improved the stiffness and strength of the specimens significantly. Failure modes of SV series and SD series showed shear fractures and flexure fractures at ultimate state respectively. SD series were ductile rather than SV series.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.8
• /
• pp.975-983
• /
• 2011

A microfin on a heated surface and its effects of the heat transfer has been investigated. The thickness of the fin is about 8 micrometer to allow the flexible up-down motion of the fin. Two-way complete FSI (Fluid-Structure Interaction) method has been applied for the analysis. Firstly, the deformation of a microfin due to the pulsating flow is evaluated using structure analysis. The flow and temperature patterns are predicted by CFD (Computational Fluid Dynamics) method. At each time step, using the pressure force and temperature distribution from CFD, the deformation of the wing is evaluated by FEM. Also in order to estimate the resonance probability, the natural frequency of the wing structure is calculated by modal analysis. The proposed numerical procedure was validated through experiment using a single fin. Through this work, we show that the increase of 40% in heat transfer capacity using the microfin has been compared with that of flat plate case.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.1
• /
• pp.1-7
• /
• 2000

In this paper, we present n-channel GaAs MOSFET having $Al_2O_3$ as gate in insulator fabricated on a semi-insulating GaAs substrate. 1 ${\mu}$m thick undoped GaAs buffer layer, 1500 ${\AA}$ thick n-type GaAs, undoped 500 ${\AA}$ thick AlAs layer, and 50 ${\AA}$ GaAs caplayer were subsequently grown by molecular beam epitaxy(MBE) on (100) oriented semi-insulating GaAs substrate oxidized. When it was wet oxidized, AlAs layer was fully converted $Al_2O_3$. The I-V, $g_m$, breakdown charateristics of the fabricated GaAs MOSFET showed that wet thermal oxidation of AlAs/GaAs epilayer/S${\cdot}$I GaAs was suitable in realizing depletion mode GaAs MOSFET.