• Explosives and Blasting
• /
• v.34 no.4
• /
• pp.10-18
• /
• 2016

Explosive blasting utilizes the energy produced from the explosion of explosive materials. Since the black powder, the first type of explosive, was invented, various types of explosives have been developed until a recent emulsion explosive which is powerful as well as safe in use. The detonators continue to be developed from safety fuse to the recent electronic detonators which allow extremely accurate and flexible control of delay time. However, the good explosives and detonators do not always lead to the good blast results. It entirely depends on the blast engineer. It is necessary to develop the empirical or theoretical models based on the field experience and sound theoretical algorithm. Such models would be very useful for blast design and, furthermore, provide the idea of further technical development. This paper introduces some models used in explosive blasting and attention to be paid for field application.

• Tunnel and Underground Space
• /
• v.20 no.2
• /
• pp.125-130
• /
• 2010

Model blast experiments of mortar blocks were performed to investigate the effect of the guide hole on crack growth. The mortar block specimens have a blast charge hole and 8 guide holes. Two of circular guide hole, notched guide hole, diamond shaped guide hole and diamond shaped guide holder are installed around 110 mm, 165 mm and 220 mm apart from the charge hole for each specimen. From the blast experiments, it was revealed that all the guide hole used in this study were effective for controlling the crack growth at the fracture control.

• Explosives and Blasting
• /
• v.23 no.1
• /
• pp.65-77
• /
• 2005

Reflecting the fact that there are increasing number of old high-story apartment structures in urban area, it is expected that the demand of blasting demolition will increase in the near future. It is of great important to make up for the insufficient empirical knowledge in blasting demolition through priori method such as computer simulation. Computer simulation of the blasting demolition involves complicated process. In the past domestic researches, two-dimensional bonded particle model was used to examine the overall demolition behavior of a five-story simple structure. It was observed that the two-dimensional simulation did not properly simulate the collapsing behavior of a structure mainly due to the reduced degree of freedom. In this study, three-dimensional simulation was tried. It consumed a great amount of calculation time, which limited the extent of the study. A few parameters, such as delay times, amount of charge at each hole, ball properties, were modified in order to check oui; their effect on the collapsing behavior. The differences were observed as expected but the collapsing behavior did not exactly coincide with the test blasting with a scaled model.

• Explosives and Blasting
• /
• v.33 no.4
• /
• pp.7-13
• /
• 2015

Recently, as the demand for development and utilization of underground space is increasing worldwide, the blast damaged zone has become a major issue in constructing underground structures. In this study, to verify the explosion modelling method for blast-damaged zone (BDZ) around underground cavern, a series of small-scale test blasts was conducted using the concept of momentum trap. According to the test results, the input parameters to the numerical model (ANSYS LS-DYNA) were corrected. It is concluded that the suggested method of miniature blasting and numerical modelling using the MT concept well simulates the velocity of the MT projectile under given conditions.

• Explosives and Blasting
• /
• v.22 no.1
• /
• pp.33-43
• /
• 2004

In this study, a comparison was made between the resulting behaviors of scaled model test and particle flow analysis for blasting demolition of a reinforced concrete structure. For the test and analysis, a progressive failure of a five-story structure was considered. The dimension analysis was carried out to properly scale down the real structure into the laboratory size. The test model was made of the mixture of gypsum, sand and water along with soldering lead to analogy reinforcing steel bars. The ratio of mixing components was chosen to best represent the scaled down strength and deformation modulus. The columns and girders of the structure were precasted in the laboratory and assembled right before the blasting test. The numerical analysis of the blasting demolition was carried out using PFC2D (Particle Flow Analysis 2-Dimension by Itasca). The results of the blasting of concrete lahmen structure showed roughly identical demolition behavior between scaled model test and numerical test. For the blasting of the reinforced concrete structure, the results were more identical and closer to the real demolition behavior, since the demolition behavior was better represented in this case due to the increased tensile strength of the component.

• Tunnel and Underground Space
• /
• v.10 no.3
• /
• pp.481-485
• /
• 2000

Vibration screening trench is very effective to reduce the ground vibration, but to construct the trench in the rock mass is not easy. Various line drilling methods have been tried to replace the trenching. In this study, UDEC was applied to simulate the screening effect of drilling holes in 2 dimensional ground model. Field measurement was conducted and compared to numerical analysis.

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2000.09a
• /
• pp.235-239
• /
• 2000

Vibration screening trench is very effective to reduce the ground vibration, but to construct the trench in the rock mass is not easy. Various line drilling methods have been tried to replace the trenching. In this study, UDEC was applied to simulate the screening effect of drilling hopes in 2 dimensional ground model. Field measurement was conducted and compared to numerical analysis.

• Explosives and Blasting
• /
• v.36 no.3
• /
• pp.19-28
• /
• 2018

Locally damaged structures caused by earthquake or extraordinary external forces have been required to rapidly be dismantled because of its possibility of additional collapses. Particularly, steel frame structures were demolished by the shaped charge blasting method. Recently a research suggested a shape charge blasting technique which uses bent-shaped charge holder of copper plate and emulsion explosive charge to cut thick steel plates. This study simulated the cutting performance of the bent-shaped charge holder with considering types of explosives, thickness of copper liner and stand-off distances using LS-DYNA software. The shape charge blasting test of a 25mm thickness steel plate were used to calibrate the input parameters of the numerical models. The penetration depth and penetration width were analysed with different types of explosives, thickness of copper liner and stand-off distances.

• Explosives and Blasting
• /
• v.34 no.4
• /
• pp.28-34
• /
• 2016

Empirical model, phenomenological model, and CFD model have been used to evaluate the blast effects produced by explosion of explosives, flammable gas and liquid or dust. TNT equivalence method which is one of empirical models has been widely used as it is simple. In this study, new peak overpressure-scaled distance and scaled impulse-scaled distance equations are induced through fitting data from the curves given by TNT equivalence method. If the TNT equivalent mass is calculated, it is possible to estimate the peak overpressure and impulse using the regression equations. Differences of peak overpressure with yield factor which is a component of TNT equivalence method are found to be great in near-by distances from explosion source where the increase in overpressure is very steep, but the differences are getting smaller as the distances increase.

• Tunnel and Underground Space
• /
• v.20 no.4
• /
• pp.299-307
• /
• 2010

The model experiments, which employ a charge hole and guide hole, are simulated to examine the effect of the guide hole on the crack propagation control in blasting. Crack patterns resulted from the analysis models, which consider the distance between the charge hole and guide hole, were compared. From the simulation analysis for the model experiments, it was revealed that all the guide holes used in this study were effective for controlling the crack propagation in blasting.