• Journal of the Society of Naval Architects of Korea
• /
• v.28 no.2
• /
• pp.318-328
• /
• 1991

The present paper describes the experimental study on the fixed-type wave-energy conversion system, consisting of the OWC-type wave-energy absorbing chamber and the duct for the air turbine. For simplicity, a screen of wire mesh was employed in place of an air turbine in order to simulate its effects on OWC chamber. Experiments were performed at the towing tank in regular waves with the frequency range of 0.22-0.75Hz. Comparison wish the numerical prediction using a potential flow-based method [4] was made to validate the capability of numerical code. It was shown that the agreements between measured and calculated results are quite good, giving a confidence in prediction method. Simulation of air turbine using a wire-mesh screen was successful, at least in a qualitative sense, to investigate the inter action between the OWC chamber and an air turbine. Results also showed that the effects of a wire-mesh screen on chamber efficiency are negligible, and the present model can be effectively utilized for the practical use in ocean waves with the frequency range under 0.3Hz.

• Proceedings of the Korean Information Science Society Conference
• /
• 1999.10b
• /
• pp.595-597
• /
• 1999

기존의 LOD 제어방법들은 랜더링속도를 성공적으로 증가시켜왔으나 오버헤드가 크다는 단점을 갖고 있다. 이러한 오버헤드는 각 vertex마다 view-frustum clipping, back-face culling, 스크린 공간 기하학적 오차계산과 같은 view-dependent refinement criteria를 측정하고, 메쉬의 LOD를 바꾸기 위해서 edge collapse/vertex split를 수행하기 때문이다. 제안하는 방법은 메쉬를 여러 개의 region들로 나누고 vertex가 아닌 region에 대해 view-dependent refinement criteria를 측정하므로 오버헤드가 훨씬 작다. 또한 각 region 들의 LOD가 바뀔 때 미리 만들어 둔 LOD 버전들중에서 하나를 선택하기만 하면 되므로, edge collapse/vertex split을 수행하는 오버헤드는 없다. 실험적으로 제안하는 LOD 제어방법은 기존의 방법들보다 작은 메모리를 사용하고 LOD 제어 오버헤드도 적으며, LOD 제어를 하지 않은 경우보다 2배-5배의 랜더링 속도향상을 얻었다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.3
• /
• pp.166-173
• /
• 2012

This study is about comparison of thermal and flow characteristics on the wind & radiant heat shield with STS mesh type screen for offshore. Numerical analysis was conducted to find transmission coefficient in the mesh and then analyse the flow characteristics about wind & radiant heat shield. The experiment method of solar radiation has been used as thermal radiation source to get the performance of radiant heat shield measurement. The sensor radiation device has been used to measure the reduction of solar radiation with various size of cells and at a distance of 0.5m and 1m from the cold face of the wind & radiant heat shield.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.48-53
• /
• 2001

This experimental study is to research heat transfer characteristics in copper-water heat pipes with screen wick, the 150 and 200-mesh. Recent advances in the miniaturization and large capacity of electronic devices have had a major impact on the design of electronic equipment. As a result, a high-performance cooling system is needed. Experimental variables are inclination angle, number of layer and temperature of cooling water. The distilled water was used for the working fluid. At a inclination angle $6^{\circ}$, the 200-mesh screen wick 3-layer is shown the best heat transfer performance.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.41.2-41.2
• /
• 2005

• Journal of the Microelectronics and Packaging Society
• /
• v.5 no.2
• /
• pp.27-36
• /
• 1998

통신시스템의 고발열 전자부품 냉각을 위해 3종류의 써모싸이폰을 각각의 용도에 따라 개 발하였으며 그 각각의 설계변수에 대한 냉각특성을 실험적으로 구하였다. TS-I에서는 증발부 내부 에 금속스크린 메쉬형심지를 삽입함으로써 시간에 따른 온도 변화를 작게 하여 냉각성능 안정성을 확보하였고, TS-II에서는 9W/cm2의 높은 냉각성능을 가진 루프형 써모사이폰을 개발하였으며 TS-III에서는 작동유체의 종류, 파이프개수 와이어 삽입여부등 써모사이폰의 주요 설계변수에 따 른 냉각특성을 구하였다.

• Proceedings of the SAREK Conference
• /
• 2004.06a
• /
• pp.157-157
• /
• 2004

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.7
• /
• pp.1630-1638
• /
• 2015

In this paper, we propose a GPU-based interactive and plausible visualization method for the silt and landslide simulation results computed with SPH. By empirical experiments, we verify that our GPU-accelerated screen space mesh method can be effectively used for visualizing the landslide disaster simulation. The method proposed in this paper make it possible to overcome the limitation of previous simulations where the experience obtained by trials and errors plays the most important roles. Because the realtime visualization enables interactive observation of simulation results and efficient data assimilation, the accuracy of the simulation can be significantly improved in an efficient way.

• Tribology and Lubricants
• /
• v.38 no.5
• /
• pp.185-190
• /
• 2022

Among the operating limits of a heat pipe, the capillary limit is significantly affected by the characteristics of the wick, which is determined by the capillary performance. The major parameters for determining capillary performance are the maximum capillary pressure and the spreading characteristics that can be expected through the wick. A well-designed wick structure improves capillary performance and helps improve the stability of the heat pipe by enhancing the capillary limit. The capillary performance can be improved by forming a porous microstructure on the surface of the wick structure through surface modification techniques. In this study, a microstructure is formed on the surface of the wick by using a surface modification method (i.e., an electrochemical etching process). In the experiment, specimens are prepared using stainless-steel screen mesh wicks with various fabrication conditions. In addition, the spreading and capillary rise performances are observed with low-surface-tension fluid to quantify the capillary performance. In the experiments, the capillary performance, such as spreading characteristics, maximum capillary pressure, and capillary rise rate, improves in the specimens with microstructures formed through surface modification compared with the specimens without microstructures on the surface. The improved capillary performance can have a positive effect on the capillary limit of the heat pipe. It is believed that the surface microstructures can enhance the operational stability of heat pipes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.5
• /
• pp.365-372
• /
• 2017

Finger electrodes on a crystalline silicon solar cell are required to be constructed as narrow and thick as possible in order to minimize shading losses and electrical resistance. The most common means to construct high-aspect ratio finger electrodes has been screen-printing, but it has difficulty achieving fine finger electrodes because the as-printed finger width is generally wider by 1.3-2.2 times the screen opening width. Consequently, it requires an extremely small screen opening (below $30{\mu}m$) in order to achieve a finger width below $40{\mu}m$. However, the use of such a small screen opening could result in various problems, such as high printing pressure, defective transport of silver paste, and high electrical resistance due to unfavorable mesh marks left on the finger electrodes. In this study, dispensing printing with a screw pump is introduced as an alternative to conventional screen-printing and its unique traits in the front side metallization of crystalline silicon solar cells is discussed.