• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.3
• /
• pp.22-30
• /
• 2011

There is a many way of LPRE throttling methods, high-pressure-drop systems, dual-manifold injector, gas injection, multiple chambers, pulse modulation and movable injector components. Especially dual-manifold injector is essentially combines two fixed-area injectors into a common structure, with independent feed systems controlling flow to each injector manifold. In this paper, using indirect photography and liquid film thickness measurement with various injection pressure and tangential entry diameter to decide stability of spray over a wide thrust range in dual manifold injector.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1021-1025
• /
• 2017

Numerical heat/flow analysis was performed on a liquid rocket engine head with the cooling water manifold to ensure the durability of a ground test facility for heat exchanger. Through these studies, the shapes of the injector and the flow path were determined and applied to the head of the engine under development. Firing tests were conducted to verify the designed coolant manifold and no thermal damage was found on the engine-head-face. Comparing the combustion test results with the numerical analysis, the outlet temperature of coolant showed a difference of about $15^{\circ}C$. This trend is reasonable considering existence of LOX manifold, thermal barrier coating, and the actual location of flame.

• Proceedings of the KAIS Fall Conference
• /
• 2010.05b
• /
• pp.992-995
• /
• 2010

엔진 흡기시스템 중 흡기매니폴드는 가솔린엔진의 성능을 결정하는 매우 중요한 성능 인자이다. 본 연구에서는 1400cc급 가솔린 엔진용 흡기 매니폴드에 대한 유동해석과 리그 실험을 수행하였다. 압력차에 따른 유동 및 유량계수의 해석을 통하여 유동특성을 분석하였으며 실험적 평가를 통하여 공기유량계수의 결과치를 검증하였다. 해석과 실험 결과를 비교 분석하여, 해석값과 실험값의 오차를 확인하였다.

• Proceeding of EDISON Challenge
• /
• 2014.03a
• /
• pp.625-630
• /
• 2014

연료전지의 성능을 결정짓는 가장 중요한 변수 중의 하나는 각 스택의 채널에 얼마나 균일하게 연료를 공급할 수 있느냐이다. 본 연구에서는 네 가지의 모델을 사용하여 연료전지 매니폴드 형상에 따른 최적 설계를 수행하였다. 위 네 가지 모델은 각기 다른 기하학적 형상을 가지며 Edison CFD를 이용하여 형상 내의 유동을 비교하였다. 초기 모델에서는, 입구부에서 매니폴드로 유입되는 유동의 확산이 잘 일어나지 않아 각 채널의 질량유량이 불균일한 분포를 보였으며 특히 속도가 빠른 중심 영역의 채널에 많은 연료가 유입되었다. 이를 위한 디퓨져 모델링이 제안되었으며 실속이 최소한도로 발생할 때 채널당 질량유량이 가장 균일하다고 가정하였다. 이를 위해 다양한 디퓨져 각을 가진 모델을 사용했고, 이론상으로 실속이 발생하지 않는 형상에서 가장 균일한 분포를 보임을 확인하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.622-627
• /
• 2017

In this study, the numerical analysis of propellant supply manifold of a sub-scale model combustor with the same combustion and acoustic resonance conditions as the real combustor was carried out. The analysis of the results is based on the shape of the manifold and the number and type of inflow channels. The manifold form of the main propellant was rounded so that the recirculation area was small and easy to manufacture. The liquid oxygen mainfold included a distributor to uniformly supply the flow, and since the kerosene manifold was directly in contact with the flame side, the inflow channel was formed at a radial $360^{\circ}$ so as to minimize the recirculation region. The liquid nitrogen manifold was configured as a radial inflow channel to reduce the velocity difference near the injector.

• The Korean Journal of Rheology
• /
• v.10 no.1
• /
• pp.38-43
• /
• 1998

매니폴로 부분이 선형 경사진 옷걸이형 다이의 최적 설계를 수행하였다. 다이흐름을 3차원 이용하여 해석함으로써 정확한 최적 설계결과를 얻을수 있었으며 형상 최적화 과정을 고찰함으로써 최적 설계도구의 효율성을 조사하였다. 공정의여러 매개변수들이 매니폴드의 형상에 미치는 영향을 조사하기 위하여 멱법칙 유체의 멱법칙 지수, 다이 슬롯의 두께 및 매니폴드 각도를 변화시켜며 최적 설계를 수행하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.2
• /
• pp.1-9
• /
• 2004

The flow in the LOX manifold of liquid rocket (KSR-III) has been analyzed using a CAE technique with an objective of modeling injector orifices in order to reduce the computational cost for the flow analysis without much losing the accuracy of capturing the flow physics. The numerical result shows that the flow just above the injector orifices is not uniformly distributed in terms of pressure and mass flow rate in case pre-distributors are not equipped inside the manifold. This non-uniformity of mass flux is attributed to the presence of large-scale flow patterns. Several boundary conditions which were designed to effectively replace the presence of injector orifices have been tested and it was found that a simple modeling can be possible by mimicking the actual shape of the orifices.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.145-148
• /
• 2009

Combustion tests of a fuel-rich gas generator had been conducted using the assembly of a powerpack. A gas generator is prone to longitudinal modes of combustion instabilities in a powerpack due to the increase of a characteristic length. It has been observed that the orifice inserted at the exit of the gas generator suppresses a longitudinal combustion instability. The intensities of pressure fluctuations in the manifolds and the chamber increase quadratically with a chamber pressure. Pressure fluctuations in the fuel manifold reveal two-fold strength greater than those in the oxygen manifold and the chamber. Frequency analysis indicates nonlinear characteristics inherent in the pressure fluctuations in the fuel manifold.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.3
• /
• pp.92-100
• /
• 2005

An optimal fuel manifold is suggested to improve the cooling performance of an injector face plate. The cooling performance at the center area of the injector face plate is to be augmented while the spatial injection uniformity is maintained. The comparison of the cooling performance of f candidates gives the conclusion that the dividing plate from 2-3 injector .ow to 9-10 injector. row is an optimal. The maximum face plate temperature decreases by 27$\%$ while the injection uniformity is close to that of the original design. The pressure drop in the fuel manifold of the optimal design is also same as the original design.

• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.113-122
• /
• 2002

A numerical analysis on the uniformity of propellant injection velocity of KSR-III has been carried out to give design improvements. Injector holes were approximated as porous media with the same pressure drop . The injection velocity is higher at the opposite side of the inlet for both LOX and fuel due to the static pressure rise in the stagnation region. Flow passages at the vertical circular plate in the LOX dome increase the uniformity of LOX injection. Little change was observed in the injection uniformity and pressure drop for the slanted LOX passage. Also provided were the O/ F ratio distributions from the oxidizer/ fuel injection velocity analysis.