• 한국가스학회지
• /
• 제19권3호
• /
• pp.49-53
• /
• 2015

이 논문의 목적은 자동차 클러치, 수동변속기와 타이어 시스템의 마찰에 관련된 화재에 대한 고장사례를 분석하고 연구하는 것이다. 첫 번째 사례는 반복적으로 클러칭하면서 자동차의 클러치 디스크가 플라이 휠의 접촉면과 접촉하면서 열에 의해 과열되어 이 열이 수동변속기의 외부로 흘러 고착된 오일 찌꺼기에 옮겨 붙어 화재가 발생된 것으로 확인되었다. 두 번째, 사례로 변속 장치는 기어와 기어의 접촉에 의해 동력을 전달한다. 변속기 오일이 변속기 케이스의 균열로 인해 오일 부족 현상이 일어나 변속기 케이스 상단의 퇴적물에 의해 화재가 발생된 것을 확인하였다. 세번째 사례는 건조한 구덩이에서 빠져나오려고 반복적으로 가속페달을 작동시키면서 타이어와 도로의 마찰이 반복되면서 내부의 축적된 열에 의해서 화재가 발생된 것으로 확인되었다. 따라서, 운전자는 운전 중 마찰부에 화재가 발생하지 않도록 세심하게 관리하여야 한다.

• 대한기계학회논문집A
• /
• 제37권3호
• /
• pp.373-378
• /
• 2013

엔진의 출력증대와 이에 따른 변속기의 크기 증가 등으로 인한 회전체의 관성증가로 변속기의 변속성능은 악조건이 되고 있다. 따라서, 이를 해결하기 위하여 내마모성이 높은 마찰소재의 개발이 요구된다. 디젤차량 수동변속기용 싱크로나이저 링에 요구되는 마찰특성에 적합한 소재를 개발하고, 이에 대한 접합 특성을 평가하였다. 즉, 철합금 모재와 동합금계 마찰재를 접합하는 공정을 개발하고, 접합층에 대하여 BSE분석, EDX분석을 수행하여 접합특성을 평가하였으며, 해당 시험편에 대하여 전단강도를 평가하였다.

• 한국공작기계학회논문집
• /
• 제15권2호
• /
• pp.44-50
• /
• 2006

A driver's feelings of transmission serve as a basis to judge not only the transmission but also the entire automobile that he or she drives. The importance of transmission feelings is increasing daily because of driver's desire for increased torque and other improved functions. In order to accommodate such desire of drivers, new friction materials have been developed. The study in this report compared the affects of such materials and the force for transmission theoretically and empirically. By doing so, the study attempted to establish basic references for computation of capacity and other factors to be determined at the time of design of synchronizer system.

• 한국자동차공학회논문집
• /
• 제2권5호
• /
• pp.110-120
• /
• 1994

Due to the increasing demands in comfortable drivability, most motor companies are developing their own unique shift controller to suppress the shift shock induced by gear change. For a typical automatic transmission system, the dynamic constraints of friction clutch was clarified for efficient program development and major factors effecting the shift transient was confirmed by simulation study. The MIMO LQG/LTR controller was designed to control the turbine and corresponding gear speed. By establishing the control strategy recalling transient response during shift the speed controller mentioned above was used as an indirect torque controller. Consequently a new concept for a systematic design method of shift controller applicable to wide-varying systems was suggested which is time efficient and cost efficient saving a lot of experimental study.

• Tribology and Lubricants
• /
• 제29권1호
• /
• pp.1-6
• /
• 2013

Hydraulic transmission is the main component delivering power to the drive wheels of an excavator during forward and backward movement, and it has low speed, high torque and high speed, low torque gear change ratios as a forward/backward two-speed main function. It also has additional function of ensuring that the excavator is stably fixed on the ground with the built-in parking brake during excavation operations. In this study, optimal design specifications are determined by modeling and simulating about the multi-disc-type friction clutch, which is the main component improving the reliability of the hydraulic transmission for a 14-ton wheel excavator, and the friction properties of the transmission clutch are analyzed by performing sample tests.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.226-233
• /
• 1998

In this paper, an experimental study was performed to investigate the speed ratio-torque-thrust characteristics for metal belt CVT. It is observed from the experimental results that nondimensional secondary thrust force follows with the existing theoretical formula with ${\mu}$=0.09~0.12 depending on the torque and the speed ratio. In order to represent these characteristics, an effective friction coefficient was introduced. Also, the slip characteristics between the belt and the pulley were investigated experimentally and traction coefficients at gross slip were obtained for various speed ratios. Using the traction coefficients and the effective friction coefficients, an improved formula for the secondary thrust force was suggested assuming that thrust force is the summation of the thrust of pseudo inactive arc and the thrust of pseudo active arc. The effective friction coefficient and the improved formula for the speed ratio-torque-thrust relationship suggested in this work can be used to obtain the appropriate secondary thrust.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1989년도 제10회 학술강연회초록집
• /
• pp.16-40
• /
• 1989

엔진오일 첨가제는 오일 전체의 성질에 영향을 주는 것과 윤활 부품의 표명 성질에 영향을 미치는 것으로 크게 구분할 수 있다. 표면 작용용 첨가제 들의 상호작용은 기대이하의 성능을 발휘하는 경우가 있고 그 원인은 첨가제의 상호작용에 의한 것으로 볼 수 있으므로 가능한 범위내에서 실험적으로 살펴보기로 한다. 현대자동차의 엔진과 변속기에 요구되는 윤활유 성능 특성을 만족시키기 위해서는 기유에 요구되는 적당한 성능을 발휘하기 위한 특수한 첨가제를 넣어주어야만 한다. 그러나 첨가제를 개발하는 과정에서 한가지 첨가제의 특성은 그 자체를 실험한 경우와 매우 상이한 결과가 완전히 혼합된 오일에서 나타남을 경험하게 된다. 이것은 첨가제들 자체의 상호작용에 의한 원인으로 암시되지만 이들에 관련된 연구나 지식은 상당히 제한되어 있다. 따라서 첨가제으 상호작용에 관한 실례를 찾아보고 관련자료를 검토해 보는 것은 의미있는 일이라 생각된다. 윤활오일 첨가제가 오일 자체의 성질에 영향을 주는 것으로 점도 시수향상제, 산화 방지제 같은 것이 있고 마찰 표면 특성에 영향을 미치는 내마모성 첨가제, 극압첨가제, 청정제, 분산제, 마찰 계수 감소제 등으로 크게 구분된다. 오일자체에 영향을 미치는 첨가제는 서로 별개로 작용하지만 그래도 상호 반응을 할 수 있다. 예를 들면 자유기 억제제와 과산화물 분해형식의 산화억제제의 혼합물은 산화억제 성능을 최대화 시켜준다.

• 한국자동차공학회논문집
• /
• 제16권4호
• /
• pp.103-109
• /
• 2008

Semi-spherical CVT(SS-CVT) is one of friction drives, which transmits power via the friction force between a spherical shaped variator and output disks. The variator varies the speed ratio of SS-CVT continuously as well as transmits input power into the output shaft. Therefore two friction forces are normally applied on the variator; one is the longitudinal friction force for power transmission and the other is the lateral for shifting. In order to investigate the dynamic behavior of SS-CVT, we introduced a numerical model of 2-dimensional friction force using a function of slip ratio and slip angle. And a dynamic model, which describes the shifting mechanism of SS-CVT, is developed through 3-dimensional vector analysis. Finally we presented numerical results of the shift characteristics focused on the transient behavior of the variator's slip ratio and slip angle. The numerical results also show the typical CVT shifting characteristics of SS-CVT and stable shifting behaviors of the variator.

• Tribology and Lubricants
• /
• 제30권5호
• /
• pp.265-270
• /
• 2014

Frictional heat greatly influences the friction behaviors during clutch engagement. Therefore, the engagement of a wet or dry clutch is frequently not under control by the frictional heat. In a wet clutch, the frictional temperature also specially needs to be controlled, and in many cases, the clutch material is selected to prevent a temperature rise from the friction between friction pad and separator. However, only the selection of the clutch material cannot ensure sufficient control of the temperature rise by the friction. The groove pattern on a friction pad is designed for more flow rates of transmission fluid between the contact gap of clutch pad and separator for the cooling effect. In this work, grove patterns are designed for more flow rates out of the contact gap between friction pad and separator plate. Selected groove design shows the improvement flow rates of transmission fluid through both inner and outer radius, where most of the transmission fluid flows through the outer radius when the clutch is engaged due to the centrifugal force in conventional wet clutch groove. Several comparisons of the amounts of frictional heat generated on clutch pads are made in order to verify the decrease of the temperature rise according to the flow rates along the groove patterns.

• 한국자동차공학회논문집
• /
• 제7권8호
• /
• pp.132-142
• /
• 1999

In this paper, a new formula for primary and secondary thrust of metal belt CVT is proposed considering variation of band tension, block compression and active arc for each of the primary and secondary pulleys. For the secondary thrust, effective friction coefficient is introduced considering the effect of flange deflection. Nondimensional primary and secondary thrust of the metal belt CVT by the new formula agree well with the experimental results except for low torque range, $0\;<\;{\lambda}\;<\;0.2$ at speed ration i = 1.0. The new formula can be used in design of the primary and secondary thrusts control system for the metal belt CVT.