• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.2
• /
• pp.191-199
• /
• 1993

Diffusion of a steady horizontal line source in a turbulent shear flow is simulated by numerically solving a steady two-dimensional advective diffusion equation. The computational result is compared with the analytic solution for uniform velocity and diffusivity distributions over the depth. The analytic solution for constant velocity and diffusivity overestimates the degree of vertical mixing. The normalized equation indicates that friction factor is the only physical parameter that governs the vertical diffusion process. Sensitivities of the diffusion process to the friction factor and initial source position are analyzed. The rate of vertical mixing varies approximately as the square root of the friction factor. The optimal source position, which gives the most rapid mixing, lies above the mid-depth and moves toward the water surface as the friction factor increases.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.8
• /
• pp.905-910
• /
• 2013

The flow analysis has been made by applying the turbulent models in the helically coiled tubes of heat transfer. The k-${\varepsilon}$ and Spalart-Allmaras turbulent models are used in which the structured grid is applied for the simulation. The velocity vector, the pressure contour, the change of residuals along the iteration number and the friction factors are simulated by solving the Navier-Stokes equations to make clear the Reynolds number effect. The helical tube increases the centrifugal forces by which the wall shear stress become larger on the outer side of the tube. The centrifugal force makes the heat transfer rate locally larger due to the increase of the flow energy, which finds out the close relationship between the pressure drop and friction factor in the internal flow. The present numerical results are compared with others, for example, in the value of friction factor for validation.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.2
• /
• pp.29-37
• /
• 2017

As the behavior of the debris flow due to the torrential rains in mountain is affected by shear strength and rheological properties of the fine fraction in the ground, the evaluation of both properties is necessary to estimate the behavior of the debris flow. The objective of this study is to evaluate the shear strength and rheological properties using the direct shear apparatus. The direct shear tests are conducted for two kinds of fine-grained soil specimens, which are in dry state and liquid limit state. From the direct shear tests, shear strengths are measured according to the normal stresses applied on the specimens to evaluate the cohesion and internal friction angle. In addition, reversal shear tests are performed for the fine-grained soil specimens in liquid limit state according to the shear rate to evaluate the residual shear strength. The results of direct shear tests show that the specimen at the liquid limit state has lower internal friction angle and higher cohesion compared to the dry stated, and the residual friction angle and cohesion at the residual state are lower than those at the peak state. In the result of reversal shear test, the residual shear strength is directly proportional to the shear rate and viscosity is calculated as $73.60Pa{\cdot}s$. This study demonstrates that the direct shear apparatus can be effectively used for the evaluation of the shear strength and rheological properties of the fine-grained soils related with the debris flow.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.4
• /
• pp.769-777
• /
• 2015

In this study, the rheological models were introduced and developed to reflect rate dependent tensile behaviour of concrete. In general, mechanical properties(e.g. strength, elasticity, and fracture energy) of concrete are increased under high loading rates. The strength of concrete shows high rate dependency among its mechanical properties, and the tensile strength has higher rate dependency than the compressional strength. To simulate the rate dependency of concrete, original spring set of RBSN(Rigid-Body- Spring-Network) model was adjusted with viscous and friction units(e.g. dashpot and Coulomb friction component). Three types of models( 1) visco-elastic, 2) visco-plastic, and 3) visco-elasto- plastic damage models) are considered, and the constitutive relationships for the models are derived. For validation purpose, direct tensile test were simulated, and characteristics of the three different rheological models were compared with experimental stress-strain responses. Simulation result of the developed visco-elasto-plastic damage(VEPD) model demonstrated well describing and fitting with experimental results.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1991.10a
• /
• pp.348-361
• /
• 1991

When reinforcing strip footing on a sand 8round with reticulated root piles, reinforcing effect depends on the length , number, cross sectional area, penetration angle, spacing, and Young's modulus of piles. the mode of action of reinfocement tendons in soil isn't one of carring developed tensile stresses but of anisotropic(uni-directional) reduction or even supression of one normal strain rate. R. H. Bassett and N. C. Last proposed that the reinforcement should be located on the direction of minor strain rate which coincides with the tensile strain rate in the velocity characteristics. Based on this proposal the author carried out a series of 2 - dimentional finite element analysis which varies the parameters mentioned above.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.10 no.6
• /
• pp.88-95
• /
• 1996

The ultrasonic motor(USM) has good characteristics such as compact size, silent motion, high speed responce, low speed and high torque. The USM is driven by 2-phase AC electricity. The control parameters of USM are voltage, phase, and frequency of input powers, etc. In this paper, a voltage difference control is proposed. The voltage difference control has more advantage than phase difference control. Specially, current and power is lower than that of phase difference control. For this voltage diffrence control, we designed USM controller to adjust volatage and phase using PLSI(Programmable Large Scale Integration).

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.6 no.2
• /
• pp.183-190
• /
• 1982

이 논문에서는 유압제어장치의 응답에 대하여 관성하중, 점성하중, 쿨룸(Coulomb)마찰 및 입력 신호의 주파수가 시스템에 미치는 영향을 고찰하였고, 이에 따른 속도와 압력파형을 주로 서 술하였다. 피스톤의 드리프트(drift)와 스프링하중을 제외한 대부분의 요소가 고려되었다. 추출된 방정식은 모두 무차원화 하였으며 입력 신호를 계단함수로 할 때에는 위치 피이드백 (feedback)이 삽입되었다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.3
• /
• pp.269-276
• /
• 1985

본 논문에서는 이러한 두꺼운 3차원 난류 경계층의 체계적인 연구를 위하여 적합한 수학선형을 개발하고 저속풍동에서 경계층 실험을 수행하였다. 이 수학선형 은 가능한 실제 선체주위의 유동특성이 잘 나타나도록 설계되었다. 실험을 통하여 전체적 유동을 파악하고 표면에서 평균 속도분포, 마찰저항계수 및 각종 적분변수들을 측정하였다.

• Journal of Biosystems Engineering
• /
• v.12 no.4
• /
• pp.22-30
• /
• 1987

실린더로부터 Prandtl수가 0.7인 주변공기로 전달되는 혼합대류 열전달현상을 Stream-Vorticity 함수로 표시된 재배방정식으로부터 유한차분법으로 분석하였다. Nusselt수와 실린더 주변의 온도분포가 조사된 제1편에 이어 Reynolds수와 Gradhof수가 실린더 주변의 공기속도분포, 경계층 박리지점(Separation point), 실린더 표면에서의 마찰계수 및 실린더 주변에서의 압력분포에 미치는 영향을 분석하였다.

• Proceedings of the Korean Fiber Society Conference
• /
• 2001.10a
• /
• pp.71-74
• /
• 2001

폴리에스테르 섬유는 섬도가 가늘어질수록 전체 표면적이 증가하므로 염색시 초기 염색속도가 빨라져 불균염의 원인이 되며, 겉보기 염착량은 감소하여 많은 염료를 사용해야 된다. 그래서 해도형 초극세 폴리에스테르 섬유는 레규라 폴리에스테르보다 세탁견뢰도 및 습마찰견뢰도가 현저히 저하하게 된다[1-3]. 또한 초극세 폴리에스테르 섬유는 환원세정을 하더라도 마무리 열고정이나 가공시에 가해주는 열로 인해 열이행이 많이 일어나는 것이 세탁견뢰도를 저하시키는 원인으로 지적되고 있다[4, 5]. (중략)