• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.870-873
• /
• 2007

하천의 수공 구조물은 홍수 시 작용하는 유수력에 대한 안정성을 확보해야 한다. 본 연구에서는 최근 개발된 친환경 식생호안블록인 중공블록을 하상에 설치할 경우 흐름에 미치는 영향을 연구하였다. 중공블록을 설치한 개수로에 대한 수리모형 실험을 실시하여 흐름저항과 경계층 특성에 대한 중공블록의 영향을 평가하였다. 흐름저항 특성 인자인 Manning의 조도계수와 Darcy-Weisbach의 마찰손실계수는 일정한 유량과 하상경사의 경우 수심에 큰 영향을 받고 이들은 서로 비례관계에 있음을 확인하였다. 그러나 마찰손실계수가 증가하더라도 어느 한계점 이상이 되면 조도계수는 일정한 값으로 수렴한다. 개수로의 경계층의 높이는 하천의 흐름특성과 구조특성을 반영하는 것으로 수심, 유속, 에너지경사, 경계면의 상대조도, Reynolds수, Froude수 등의 함수로 나타낼 수 있다. 중공블록이 설치된 개수로의 조도계수는 일반하천의 경우와 비교하여 큰 값을 나타내고 있어 중공블록이 흐름저항을 크게 증가시키는 것으로 판단된다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.10
• /
• pp.2159-2164
• /
• 2002

This paper reports on the effects of additional factors on the engine friction characteristics. The total friction loss of engine is composed of pumping and mechanical friction loss. The pumping loss was calculated from the cylinder pressure, and the mechanical friction loss was measured by strip-down method under the motoring condition. The various parameters were tested. The engine friction loss was much affected by oil and coolant temperature. The low viscosity oil was very effective to reduce the friction loss, and friction modifier was very useful to reduce the friction loss at lower engine speed. The engine friction loss was varied with engine running time because of surface roughness decreasing and oil degradation. To prevent oil-churning effect, it was very important to maintain the proper oil level. The presented results will be very useful to understand friction characteristics of engine.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.18 no.1
• /
• pp.109-117
• /
• 2016

This paper is focused on the determination of friction parameter which is a predominant factor in the design of inflatable structure system. This inflatable structure system is very valuably used to protect passively and rapidly the possibilities of tunnel damages by flooding threats and unusual leakage to be occurred during and after underground infrastructure construction. In particular, this system should be necessary in subsea tunnel. This study presents the experimental results obtained from the relative friction characteristics tests of the fabric materials that constitute the inflatable structure. In order to evaluate the relative friction behaviour of the inflatable structure system, friction tests and scaled model tunnel friction tests are carried out. The friction tests are carried out to determine the friction coefficient for different surface conditions between tunnel and inflatable structure. These friction coefficients are then evaluated and compared with the result obtained from the model tunnel friction tests. Interaction behaviours between tunnel and system are also reviewed and described in this study. The results clearly show that the friction coefficients derived from scaled model slippage tests are about 12% lower than values obtained from the friction tests. In addition, this study will be necessary to verify the real friction behaviour with prototype tests before applying in practice.

• Journal of the korean Society of Automotive Engineers
• /
• v.2 no.1
• /
• pp.9-20
• /
• 1980

디이젤기관의 냉시동성이 가솔린기관에 비하여 떨어지는 것은 이미 우리가 알고 있는 사실이다. 근년에는 소형트럭, 승용차, 소형건설기계 등의 분야에 있어서도 고속디이젤기관을 널리 사용하게 되었고 앞으로 디이젤연료의 중질화 및 세탄가 저하의 영향 등을 고려할 경우 시동성의 확보는 더욱 중요한 문제로 된다. 시동성에 영향을 미치는 인자 혹은 시동성개선의 방책으로서는 분 무의 착화에 직접 관련되는 것 외에 축전지의 저온특성 혹은 기관의 마찰토오크 등 여러가지에 걸쳐 있으나 이들 중에서 특히 분무의 착화에 직접 관련되는 방책에 관해서는 그것이 시동성에 미치는 영향에만 그치는 것이 아니고 시동개시직후에 있어서 배출가스, 혹은 출력성능 등에 미 치는 영향에 대해서도 함께 고려를 하여야 할 경우가 있다. 본고에 있어서는 냉시동시의 분무의 착화에 대하여 직접 관련하거나 그것을 촉진시킨다고 생각되는 몇개의 인자와 구체적인 방책을 취급하므로써 그것들이 시동성 및 시동직후의 청백연 혹은 출력성능 등에 대하여 미치는 영향에 대해서 기술하며 아래에서 취급되는 시동시의 착화를 촉진하기 위한 실제적인 인자 및 방책은 어느 것이나 기본적으로는 하나의 개념에 집약된다. 즉 그것은 연표와 효소로부터 이루어지는 연소계에 있어서 착화조건을 갖추어야함을 말할 것도 없다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.1
• /
• pp.116-122
• /
• 1988

Interfacial shear stresses have been determined for countercurrent stratified flow of air and water in a nearly-horizontal rectangular channel, based upon measurements of pressure drop, gas velocity profiles and mean film thickness. A dimensionless correlation for the interfacial friction factor has been developed as a function of the gas and liquid Reynolds numbers. Equivalent surface roughnesses for the interfacial friction factor have been calculated using the Nikuradse correlation and have been compared with the intensity of the wave height fluctuation on the interface. The results show that the interfacial shear stress is mainly affected by turbulent mixing near the interface due to the wave motion rather than by the roughened surface.

• Journal of the KSME
• /
• v.29 no.2
• /
• pp.125-137
• /
• 1989

구름접촉 피로는 반복적인 구름 접촉에 의해 나타나는 것으로서 피로의 원인이 되는 반복 하중이 두 물체의 반복적인 접촉에 의해서 일어난다는 점 때문에 일반적으로 피로연구 분야에서 다루 어지지 않고 마멸, 마찰 연구 분야에서 다루어지고 있다 구름접촉 피로현상이 나타나는 실제 예로서 베어링, 철도레일 등이 있다.

• Solar Energy
• /
• v.17 no.4
• /
• pp.13-22
• /
• 1997

Drag reduction produced by the dilute solution of polymer under turbulent flow in a rotating disk apparatus(RDA) was investigated in this study for the purpose of potential application to the Ocean Thermal Energy Conversion(OTEC) system. Four different molecular weights of poly(ethylene oxide)(PEO) were used as drag reducing additives, and synthetic seawater was adopted as a solvent. Experiments were undertaken to observe the dependence of drag reduction on various factors such as polymer molecular weight, polymer concentration and the rotating speed of the disk. The concentration dependence on the drag reduction of this polymer system was shown to obey an empirical drag reduction equation of the Virk's universal correlation.

• The korean journal of orthodontics
• /
• v.28 no.5 s.70
• /
• pp.813-823
• /
• 1998

The frictional force has been considered as an harmful factor in an active unit where tooth movement occurs, but as an advantageous factor in anchor unit that resist tooth movement. That is, efficient tooth movement is planned by using ligation methods that have low levels of bracket-wire frictional force and the anchorage control can be achieved by using ligation methods that have high levels of bracket-wire frictional force that result in binding of the bracket accompanied by little or no tooth movement. The purpose of this study was to evaluate the frictional force generated between bracket and wire in accordance with the methods of ligation, the material of ligation and the passage of time under artificial saliva. Tested were 0.017x0.022 inch stainless steel wires in standard edgewise twin brackets for upper central incisors in a 0.018-inch slot. The wires were ligated into the brackets with elastomeric modules and stainless steel ligatures. Whole tie, half tie, twisting tie and double overlay tie were done with elastomeric modules. With 0.009-inch stainless steel ligature whole tie and half tie were done by needle holder and whole tie by ligature tying plier. With 0.012-inch stainless steel ligature whole ties were done by needle holder. Whole tie groups of elastomeric module were kept in artificial saliva bath at $37^{\circ}C$ for 28 days. The frictional force was recorded by means of an Instron universial testing instrument (4202 INSTRON, Instron Co., U.S.A.) at initial, 7, 14, 21, and 28 days. The results for ligated samples in a simulated oral environment revealed the fellowing : ${\cdot}$In elastomeric module whole tie, 28 days group was significantly greater mean static frictional force than any other group but there were no significant differences among any other group (p>0.05). ${\cdot}$Elastomeric module twisting ties were significantly greater mean static frictional forces than any other ligation method but there were no significant differences between twisting tie and double overlay tie (p>0.05). Twisting tie, double overlay tie, whole tie, half tie showed differences in decreasing order. ${\cdot}$Stainless steel half tie produced lower mean static frictional force than whole tie, ligation by ligature tying plier produced greater mean static frictional force than by needle holder and ligation with 0.012-inch stainless steel ligature produced greater mean static frictional force than with 0.009-inch stainless steel ligature (p<0.05). ${\cdot}$There were no significant differences between the mean static frictional forces of elastomeric whole tie and stainless steel whole tie (p>0.05).

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.1
• /
• pp.155-164
• /
• 2002

The journal bearings use in machine parts which move relative to each other and those reduce friction and wear of journals. The journal bearings are designed to operate in the hydyodynamic lubrication regime, but elastohydrodynamic lubrication nay occur if the pressures are too high or the running speeds are too low at machine elements. It is the phenomenon that the lubricant film is broken and some parts of surfaces are in rolling contact, so that wear will increase in mixed lubrication regime. The purpose of this study is to minimize the wear rate of journal bearings for extending machine life. The wear mate in mixed lubricated regime is selected as objective function because most of wear of the journal bearings develops in elastohydrodynamic lubrication. The journal bearings we represented by a bearing radius, shaft radius, and bearing width, but the bearing radius only is selected as design variables due to a bearing radius has an influence on friction loss, stability limit velocity, and film parameter, which are used as constraints. For numerical calculation, PLBA, that is a class of the RQP algorithm, is used.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.9-15
• /
• 2018

The turbochargers, which are used widely in diesel and gasoline engines, are an effective device to reduce fuel consumption and emissions. On the other hand, turbo-lag is one of the main problems of a turbocharger. Bearing friction losses is a major cause of turbo lag and is particularly intense in the lower speed range of the engine. Current turbochargers are mostly equipped with floating bearings: two journal bearings and one thrust bearing. This study focused on the bearing friction at the lower speed range and the experimental equipment was established with a drive-motor, load-cell, magnetic coupling, and oil control system. Finally, the friction losses of turbochargers were measured considering the influence of the rotating speed from 30,000rpm to 90,000rpm, oil temperature from $50^{\circ}C$ to $100^{\circ}C$, and oil supply pressure of 3bar and 4bar. The friction power losses were increased exponentially to 1.6 when the turbocharger speed was increased. Friction torques decreased with increasing oil temperature and increased with increasing oil pressure. Therefore, the oil temperature and pressure must be maintained at appropriate levels.