• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.5
• /
• pp.10-24
• /
• 2007

In the dissertation, a power conversion system for fuel cell is composed of a PWM inverter with LC filter in order to convert fuel cell voltage to a single phase 220[V]. In addition, new insulated DC-DC converters are proposed in order that fuel cell voltage is boosted to 380[V]. In this paper, it requires smaller components than existing converters, which makes easy control. The proposed DC-DC converter controls output power by the adjustment of phase-shift width using switch $S_5\;and\;S_6$ in the secondary switch which provides 93-97[%] efficiency in the wide range of output voltage. Fuel cell simulator is implemented to show similar output characteristics to actual fuel cell. Appropriate dead time td enables soft switching to the range where the peak value of excitation current in a high frequency transformer is in accordance with current in the primary circuit. Moreover, appropriate setting to serial inductance La reduces communication loss arisen at light-load generator and serge voltage arisen at a secondary switch and serial diode. Finally, TMS320C31 board and EPLD using PWM switching technique to act a single phase full-bridge inverter which is planed to make alternating current suitable for household

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.360-369
• /
• 2008

The solar cells should be operated at the maximum power point because its output characteristics were greatly fluctuated on the variation of insolation, temperature and load. It is necessary to install an inverter among electric power converts by means of the output power of solar cell is DC. The inverter is operated supply a sinusoidal current and voltage to the load and the interactive utility line. In this paper, the proposes a photovoltaic system is designed with a step up chopper and single phase PWM voltage source inverter. Synchronous signal and control signal was processed by one-chip microprocessor for stable modulation. The step up chopper is operated in continuous mode by adjusting the duty ratio so that the photovoltaic system tracks the maximum power point of solar cell without any influence on the variation of insolation and temperature for solar cell has typical dropping character. The single phase PWM voltage source inverter is consists of complex type of electric power converter to compensate for the defect, that is, solar cell cannot be develop continuously by connecting with the source of electric power for ordinary using. It can be cause the efect of saving electric power, from 10 to 20%. The single phase PWM voltage source inverter operates in situation, that its output voltage is in same phase with the utility voltage. The inverter are supplies an ac power with high factor and low level of harmonics to the load and the utility power system.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.6
• /
• pp.951-956
• /
• 2011

CAN communication developed for communication between electric control devices in vehicle, was recently applied to automatic breaking devices, and can also be applied to field bus for production automation. Recently, field bus is introduced in engine control etc., for large ship. In this paper, cabin access control system is implemented, based on CAN communication. The cabin access control system based on CAN communication consists of access control server, embedded system based on ARM9, and micro-controller built-in CAN controller. The access control server can be able to manage overall access control system by accessing with manager. And embedded system adopted ARM9 processor transmits access information of RFID reader controller connected with CAN networks to server, also performs access control. The embedded system carry CAN frames to server, so it is used as gateway.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.37 no.6
• /
• pp.64-72
• /
• 2000

This paper deals with the parallel operation of two PWM converters for auxiliary block of high speed train. The parallel operation of AC/DC PWM converter controlled by 3-level PWM switching method to operate switching devices to realize a high power factor and reduce the primary side of the transformer current harmonics is proposed. In this paper, it is presented the phase shift technique between two converters switching phase, solution to eliminate the coupling effects due to the transformer and zero crossing detection method for synchronized with the source and controller. Experimental results for laboratory system with TMS320C31 microprocessor and 10［kVA］PWM converter confirm the validity of the proposed algorithm.

• Journal of Software Assessment and Valuation
• /
• v.17 no.2
• /
• pp.109-116
• /
• 2021

Traditionally, the engineering field has been dominated by face-to-face education focused on experimental practice, but demand for online learning has soared due to the rapid development of IT technology and Internet communication networks and recent changes in the social environment such as COVID-19. In order for efficient online education to be conducted in the engineering field, where the proportion of experimental practice is relatively high compared to other fields, virtual laboratory practice content that can replace actual experimental practice is very necessary. In this study, we developed a line tracer model and a virtual experimental software to simulate it for efficient online learning of microprocessor applications that are essential not only in the electric and electronic field but also in the overall engineering field where IT convergence takes place. In the developed line tracer model, the user can set various hardware parameter values in the desired form and write the software in assembly language or C language to test the operation on the computer. The developed line tracer virtual experimental software has been used in actual classes to verify its operation, and is expected to be an efficient virtual experimental practice tool in online non-face-to-face classes.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1179-1181
• /
• 1992

A discrete Pl controller is implemented easily using a micro-processor, and it can be confirmed to a adaption of a system and real time processing. In this paper, a speed controller by discrete Pl control using a IBM PC/AT(12MHz) as a micro-processor is implemented and applied to a DC servo motor. In designing the discrite Pl controller, a sampling time and a speed is accepted from key-board, and is processed the control coefficient automatically, and than calculate the gain. Therefore the speed of a DC servo motor is obtained and controlled regulaly. The designed and manufactured discrete Pl control system is experimented. The result shows the good response at the 60 RPM to 250 RPM on the load using the load-spring. The speed error is under 1% on the steady load, but nearly 2-3% on the transient load.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.3
• /
• pp.22-28
• /
• 1998

It is required to automate a manufacturing industry of a glasses frame, because of the inaccuracy in assembly and shortage of labor. So, in this paper, rim-lock electric welding system has been developed in order to automate a electric welding process and to increase welding quality. Rim-lock electric welding system consists of circular and linear feeder, holder for welding rim and lock, and the equipment for silver-lead provision and so forth. Main controller is a V55 microprocessor which is easy to be expanded into other function. Control program is programed using 'C' language which is easier than other language in coding, modification and adding function. At the practical welding that Rim-Lock electric welding system from this study is used, we can get such advantages as uniform quality of electric welding, continuous operation and improved productivity.

• Korean Journal of Optics and Photonics
• /
• v.12 no.3
• /
• pp.200-204
• /
• 2001

The structural design and the measured characteristics of optical signal amplification unit for 640 Gbps (10 Gbps$\times$64 ch.) WDM transmission systems are reported. The unit is composed of two sub gain block units for the amplification of C-band (1530-1560 nm) and L-band (1570-1600 nm), respectively. Programmable microprocessors monitor the states of operation and optimize the optical output conditions. Each sub gain block unit can maintain total optical output power of +21 dBm with gain flatness of < 1 dB and noise figure of <7.2 dB for the input power in the dynamic range from-5 to +1 dBm.+1 dBm.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.2
• /
• pp.273-278
• /
• 2012

In this contribution, we design and implement an SPI hardware interface for the microprocessor to communicate with the MMC (Multi-Media Card) in an embedded system. Proposed architecture is compatible with the APB in AMBA bus architecture. Embedding OS in an embedded system means a big burden in terms of hardware and software ending up with performance decline. In this paper, we adopt the concept of SPI communication without using OS in the embedded system and implement in a form of FPGA chip. The designed SPI module was automatically synthesized, placed, and routed. Implementation was performed through the Altera FPGA and well operated at 25MHz clock frequency, which satisfied our target speed.

• Proceedings of the KIEE Conference
• /
• 1998.11b
• /
• pp.432-434
• /
• 1998

Recently, For the material transport is increased, the AGV(Automated Guided Vehicle) is the most important part in the industrial factory. So we treat the navigation control problem and experimental results using microprocessor. In navigation control, we have faced with velocity control problem related to guide path tracking problem. Carefully, In the straight line, the AGV moves at its high speed, but in the curve line, especially when the radian ratio is very big it is difficult to follow guide line. So, Using fuzzy controller we have simulated the guide path following AGV according to the varying velocity and experimented it with microprocessor.(Intel 80C196KC) Now, If we use the AGV industrial factory, we will improve the product and efficiency in spite of changing the factory environment.