• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.28-28
• /
• 2003

고온가압소결(Hot Pressing) 된 다이아몬드 공구용 Co-Fe, Co-Ni계 금속본드의 상온 건식 미끄럼 마멸시험을 행하고, 조성에 따른 각 본드의 마멸 특성을 비교하고 마멸 기구를 규명하였다. 미끄럼 마멸시험은 pin-on-disk 형태의 마멸시험기를 사용하여 각 조성의 성분, 적용하중 그리고 마멸상대재를 변수로 상온, 대기 중에서 실시되었다. 마멸속도는 마멸시험 전후의 시편의 무게 감량을 이론밀도와 거리로 나누어 계산되었다. 마멸기구의 규명을 위하여 시험된 시편의 마멸면과 마멸단면을 SEM과 EDS를 이용하여 분석하였다. 시험 결과 Co-Fe system의 경우 그 마멸속도는 마멸상대재의 영향보다는 Fe 첨가에 따른 시편의 미세조직과 기계적 성질의 차이에 따라 크게 변화하였다. 그러나 Co-Ni system의 마멸속도는 마멸 상대재에 따라 크게 변화하는 것이 관찰되었다. $Al_2$O$_3$를 상대재로 마멸된 경우에는 마멸속도가 시편/상대재 접촉면에서 형성되는 산화층의 영향을 크게 받았고, glass bead(83% SiO$_2$)를 상대재로 한 경우에는 시편의 경도와 마멸속도는 서로 반비례하였다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.27-27
• /
• 2003

무가압침투법으로 제조된 부피분율 10~24% SiC, TiC, B$_4$C 탄화물 입자강화 7075 Al 합금 기지 복합재료의 건식 미끄럼 마멸거동을 강화입자의 종류, 크기 및 부피 분율을 변수로 연구하였다. 미끄럼 마멸 시험은 pin-on-disk 형태의 마멸 시험기를 사용하여, AISI 52100 베어링강을 상대재로 상온 대기 중에서 실시되었다. 마멸특성의 분석과 마멸기구의 규명을 위하여 마멸면과 마멸단면을 SEM, EDS를 이용하여 분석하였다. 제조된 복합재료의 압축 시험을 통하여 측정된 항복강도와 가공경화지수는 서로 반비례하였고, 각 시편간의 경도 차는 크지 않았다. 마멸 시험결과, 크기 및 부피 분율이 7$\mu\textrm{m}$ !0%인 SiC 입자로 강화된 복합재료를 제외하고, 전체 복합재료 시편은 7075 Al 기지 합금에 비해 낮은 마멸 속도를 보였다. 10N 이하의 저하 중에서는 강화상의 종류와 상관없이 복합재료는 낮은 마멸 속도를 보였고, 25N 이상의 고하중에서는 TiC 입자강화 복합재료가 가장 낮은 마멸 속도를, SiC 입자강화 복합재료가 가장 높은 마멸 속도를 나타내었다. 강화 입자의 크기 및 부피 분율이 동일한 경우 SiC 입자로 강화된 복합재료가 가장 낮은 내마멸성을 나타내었다. 강화상의 크기 및 부피 분율이 증가함에 따라 미소 마멸에서 격렬 마멸로의 천이 하중이 증가하였다.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.04b
• /
• pp.55-57
• /
• 1996

본 연구에서는 용사코팅재료의 용사기법에 따른 용가코팅층의 기계적 물성을 파악하고 SM48C 고주파 경화 시편과 용사코팅재료와의 고하중, 고속 윤활상태에 따른 슬라이딩 마멸특성을 파악하고자 하였다. Fe-Cr-B의 용사코팅 공정표면의 경도와 기공율이 슬라이딩 마멸거동에 큰 역할을 마치며, 특히 표면 기공율은 슬라이딩 조건(속도, 하중, 윤활)에 따라서 마멸특성이 우수한 최적이 영역이 존해할 것으로 판단된다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.1
• /
• pp.155-164
• /
• 2002

The journal bearings use in machine parts which move relative to each other and those reduce friction and wear of journals. The journal bearings are designed to operate in the hydyodynamic lubrication regime, but elastohydrodynamic lubrication nay occur if the pressures are too high or the running speeds are too low at machine elements. It is the phenomenon that the lubricant film is broken and some parts of surfaces are in rolling contact, so that wear will increase in mixed lubrication regime. The purpose of this study is to minimize the wear rate of journal bearings for extending machine life. The wear mate in mixed lubricated regime is selected as objective function because most of wear of the journal bearings develops in elastohydrodynamic lubrication. The journal bearings we represented by a bearing radius, shaft radius, and bearing width, but the bearing radius only is selected as design variables due to a bearing radius has an influence on friction loss, stability limit velocity, and film parameter, which are used as constraints. For numerical calculation, PLBA, that is a class of the RQP algorithm, is used.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1992.11a
• /
• pp.31-37
• /
• 1992

금형을 이용하는 소성가공에서는 형 사이에서 셩형되는 소재가 소성변형되지만 이때 소재는 형의 표면을 따라 미끄러지면서 유동하므로 형재료와 소재간에는 큰 마찰력이 작용하고, 형재료는 이 마찰력에 의하여 전단응력이 작용하게 된다. 따라서 이러한 전단응력이 반복하여 작용하는 프레스가공 등에서는 형의 수명이 항상 문제가 된다. 물론 형의 수명은 형재료가 프레스압력에 견디지 못하여 형이 균열되거나 펀치가 절단되는 것 같은 형재료의 강인성이 불충분하기 때문에 비교적 조기에 일어나는 파손에 의하여 수명의 대상으로 되는 경우도 있지만 무엇보다도 형의 수명을 죄우하는 가장 중요한 사항은 형재료의 내마멸성이다. 따라서 본 연구에서서는 이들 제인자를 고려하여 Die 및 Punch의 재료로 널리 사용되는 냉간성형용 Die강인 STD 11의 마멸특성을 알기 위하여 미끄럼 속도, 접촉압력 및 미끄럼 거리등을 변화시켜 내마멸성을 나타내는 최적사용조건을 찾고자 하는 것을 목적으로 하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.1055-1062
• /
• 1988

The characteristics of tool wear and the machinability in cutting of GFRP have been studied. The wear behavior of carbide insert tools(P20, M10, K10) and Cermet in TiC grade was studied by turning of changing the cutting condition. Machinability could be estimated as the following empirical formula, CT$^{n}$ =W The main results obtained are as follows: (1) Dependence of rate of tool wear on cutting speed; with increases of cutting speed, the rate of tool wear initially increases gradually(1st range), then it increases proportionally to cutting speed(2nd range), and finally the rate is constant(3rd range). (2) When the contact length has a main, effect on tool wear, the cutting speed does nit affect the tool wear. On the contrary, the cutting speed has a main effect on tool wear, the contact length does not affect the tool wear. (3) The order of machinability is K10, M10, P20 and Cermet in TiC grade.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.11
• /
• pp.2067-2076
• /
• 2000

The experiments have been made to develop manganese-based sorbent(MT, MFT) for the removal of hydrogen sulfide from simulated hot coal gases. Manganese-based sorbents were tested in an ambient-pressure fixed-bed reactor to calculate H2S removal efficiency. and a three hole jet attrition tester to characterize the sorbent physical properties. According to the experimental results of attrition test. the attrition resistance of 5% bentonite containing sorbent was higher than that of 2% bentonite. The attrition resistances of both sorbents increased with induration temperature. Effects of sulfidation temperature. space velocity. and $H_2S$ concentrations on the $H_2S$ removal efficiency were investigated. Experimental results showed that $H_2S$ could be removed from 5,100ppmv to 20ppmv at $450^{\circ}C$, and to 30~65ppmv at $550{\sim}650^{\circ}C$ for both MT/MFT sorbents. As for the change of space velocity, the breakthrough time was decreased with space velocity.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.11a
• /
• pp.63-70
• /
• 1999

Surface hardening of plain carbon steel (SM45C) by Laser are usually much finer and stronger than those of the base metals. The present study was under taken to investigate the wear resistance and a processing parameters such as, power density, pulse width, defocusing distance, and molten depth for surface modification of plain carbon steel. The wear test was carried out under experimental condition using the wear test device, and in which the annular surfaces of wear test specimens as well as mating specimen of alumina ceramics($Al_2O_3$) was rubbed in dry sliding condition. It is shown that molten depth and width depend on defocusing distance. The wear loss on variation of sliding speed was much in lower speed range below 0.2m/sec and in higher speed range above 0.7m/sec, but wear loss was little in intermediate speed range. It depends on oxidation speed and wear speed.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.296-300
• /
• 2004

Currently. the study on structural ceramic helps to suggest the precise data of friction and wear in accordance with the various conditions in operations. Also, the study helps to predict effective operating conditions by monitoring the occurrence of wear transition. The studies in the Past were mainly concentrated in using identical materials. However, it is highly likely to have unqualified data from the differences of mechanical and chemical properties between ceramic materials. Thus, in this study, through conducting the ball-on-disk type wear testing, the different ceramic materials has been used to consider tribological characteristics between different ceramic materials. We conducted the wear test by using three kinds of specimen which are zirconia, alumina and silicon carbide against zirconia. We have changed the sliding velocity and the loading conditions in this test and found out that there is row friction coefficient and wear rate in the combination of zirconia and silicon carbide.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.1
• /
• pp.120-130
• /
• 1993

Generally, the machinability of materials that have a good mechanical properties is poor. For materials having a high strength, high toughness, high strength in high temperature and wear resistance, it is difficult to remove a chip from work materials. These properties are well shown in a Nickel, so this metal is used in machine materials, semi-conductor industry, metal mold and optical fields etc. But it is limitted in use because of high cost and poor machinability. In this study, the cutting of pure Nickel was conducted to examine wear of CBN, poly crystal diamond (PCD) and single crystal diamond (SCD) tools. From the result, the CBN tool is superior to poly crystal diamond tools or single crystal diamond tools in terms of tool wear and tool wear is predictable from experimental data base.