• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.8
• /
• pp.911-917
• /
• 2013

This is a thesis about the experiment of comparison characteristic of power and exhaust gas in the same condition between diesel engine that is equipped response power 220HP turbocharger to increase effectiveness of the engine which is recently used in a lot of industry which requires high power. Resulting of the experiment with natural aspiration diesel engine and turbocharger diesel engine, difference in low speed is not significant, but in high speed, effectiveness of turbocharger diesel engine is much higher than the other one. In other hand, in exhaust gas experiment, turbocharger model exhausts more $NO_X$ and $O_2$, but it doesn't significantly affect the result when it comes with decreasing of $CO_2$ and effectiveness of increased power characteristic. As a result, the turbocharger diesel engine is economically effective comparing with the natural aspiration diesel engine.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.9
• /
• pp.789-799
• /
• 2012

In this research, a high temperature superconducting(HTS) motor is designed which is adequate for an electrical aircraft by generating high power density and the potentiality of its application to an aircraft is studied. The designed motor is based on YBCO plates, HTS coils composed of Bi-2223, and ironless air cooled resistive armature. The HTS motor is designed to generate power equivalent to O-360 engine with 180HP at 2700RPM which is used for Cessna and equivalent to CFM56 engine with 18000HP at 5000RPM which is used for B-737. Also, power densities of HTS motors are compared with power densities of aircraft engines so that we can estimate the potentiality of the HTS motor as an aircraft engine.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.13 no.2
• /
• pp.1-4
• /
• 1977

The author determined the relationship between the hauling veloicty and the hydrodynamic resistance of the sablefish pot shaped conic frustum like, and induced the formulae to determine the diameter of the main line and the net horse power of the pot hauler. The results are summarized as follows: 1. The maximum hydrodynamic resistance (with its weight in water) of the pot T(kg), when the bottom webbing is covered by a cloth to imitate the catches are scattered on the bottom, is eatimated as $$ T=120v^{1.1} (0.3{\leqq}v{\leqq}0.8) $$ where v denotes the hauling velocity of the pot in m/sec. 2. When P. P. 3 strand rope is used as main line, the diameter d(mm)is recommended to satisfy the formula $$ d=72 \frac{D}{H} V^{1.1} where H denotes the depth of the fishing ground and D the intervals of the pots linked to the main in m respectively. 3. The pot hauler must displace the net horse power p(ps) of $$ P= \frac{75}{120} \frac{D}{H} v^{2.1}$$

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.4
• /
• pp.757-764
• /
• 2018

This paper describes the design and implementation of a 1hp class two-phase type BLDC fan motor used in an air conditioning system. The BLDC motor, which is implemented in this study, is not a commutator motor type with excellent lifetime and durability and is driven by two phase power source. The most important target specification of a motor used in an air conditioning system is that it has a high efficiency at the rated operating point. For this purpose, we designed the stator shape of the BLDC motor, the design of the rotor magnet, and the control circuit for driving. The BLDC motor has a structure where the motor part, the control part, and the power part are integrated. The finite element analysis was used to calculate the characteristics of the BLDC motors, and the conformity of the design results was confirmed by fabricating and testing the prototype model.

• Journal of Biosystems Engineering
• /
• v.9 no.2
• /
• pp.81-88
• /
• 1984

현재 축산농가에서 쉽게 구할 수 있는 곡류, 조사료 및 부산물을 활용하여 사료의 자급율을 높이는 것은 농가의 소득증대를 위하여 바람직한 일이다. 이러한 사료의 자급자족 체계를 위하여 소형이며 조작이 간편한 사료분쇄기가 요구된다. 따라서 농가에 많이 보급되어 있는 5~10 마력 (3.7-7.5 kw)의 동력경운기에 의하여 작동될 수 있는 소형 햄머타입의 사료분쇄기 시작기를 설계 제작하였다. 그리고 시작기의 성능을 분석하기 위하여 보리, 옥수수, 볏짚, 건초를 사료로 하여 시료의 공급율과 스크린의 구멍크기를 변화시켜가며 실험을 수행하였다. 이상과 같은 햄머 밀 시작기의 설계 및 성능시험을 통하여 얻어진 결과를 요약하면 다음과 같다. 1. 시작기의 평균분쇄능력은 보리의 경우 평균입자직경이 543 마이크론일 때 $82.7kg/kw{\cdot}h$였으며, 옥수수의 경우에는 평균입자직경이 408 마이크론일 때 $132.7kg/kw{\cdot}h$였다. 2. 최대 공급율로 분쇄할 때 소요동력은 보리의 경우 1.9kw, 옥수수의 경우 5.3kw, 볏짚의 경우 1.5kw, 건초의 경우 1.6kw을 필요로 하였으며, 5-10 마력(3.7-7.5kw)의 동력경운기로 개발된 햄머 밀을 작동함에는 별 문제가 없는 것으로 분석되었다. 3. 시작기로 시료를 분쇄할 때 곡류 분쇄는 물론 조사료 분쇄도 가능한 것으로 분석되었다. 4. 시작기에 의해 시료를 분쇄했을 때 분쇄물의 평균온도 상승폭은 $7.2-10.0^{\circ}C$였다. 이러한 온도는 분쇄물의 영양소 파괴및 저장상의 안정성을 고려할 때 안전한 범위의 온도상승으로 판단되었다. 5. 원료공급율과 스크린 구멍크기가 분쇄량과 분쇄정도에 5% 수준에서 유의성 있는 영향을 미쳤다.

• Journal of Navigation and Port Research
• /
• v.36 no.8
• /
• pp.607-612
• /
• 2012

In this paper, calculation methods of resistance of the ship to be towed and towline tension are discussed. When the vessel is fallen into dead ship condition then appropriate towing force have to be estimated to move the vessel from accident place to safe area. In this research, resistance of the ship to be towed and the tow hawser were considered to estimate total towline tension. Polynomial interpolation method is also applied to estimate additional hydrodynamic resistance of towline. Finally, UI program to calculate the resistance and total towline tension is developed. The developed program based on the research results is effective and convenient to use.

• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.1
• /
• pp.1-13
• /
• 1994

Procedures for the development of a preswirl stator-propulsion system for a VLCC 300K are described in this paper. The preswirl stator-propulsion system is one of the compound propulsor systems, which is used for the purpose of recovering propeller slipstream rotational energy by locating a stator in front of the propeller. The preswirl stator-propulsion system can be considered as a most reliable energy saving device because of its simple mechanism. Five stators are designed for the existing hull form and propeller, and their effects are verified by model tests. Open-water test result of the preswirl stator-propulsion system at the cavitation tunnel show $4{\sim}6%$ increase of open-water efficiency compared to that of a propeller without stators. Maximum 6.5% decrease of delivered power at the design speed(15.5knots) is expected with the designed stator based on the analysis results of resistance and self-propulsion test at the towing tank.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.3
• /
• pp.198-205
• /
• 2021

In this paper, the effect of trim variation on the required power of 11,000TEU container ship was investigated under conditions considering the actual operation speed and draft. For each draft condition, the effective power (P_E) and delivered power (P_D) trends were investigated with changes in trim and ship speed. At this time, the displacement volume was fixed same as the value of the even trim condition and the both sinkage at the fore and after perpendicular are confirmed. The test ship speeds were determined by considering the operating speed. Both numerical and experimental methods were used to analyze the effects of trim variation. Numerical analysis results were used for evaluating the resistance performance, and the self-propulsion performance was estimated using experimental data obtained from model test.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.5
• /
• pp.627-633
• /
• 2019

This study aimed to predict the resistance and propulsion performance of a ship using computational fluid dynamics (CFD) and a database as well as establish an assessment method for the energy efficiency design index (EEDI) using the results. First, the total resistance of the studied ship is obtained using CFD. A flow analysis is conducted with the free surface and trim and sinkage using a commercial CFD code (STAR-CCM+). The effective power of the ship is assessed based on the CFD results. The quasi-propulsive efficiency is calculated from an empirical prediction equation using experimental data and similar material. Finally, a general calculation program for the EEDI is established based on the hydrodynamic results, ship information for principal particulars, conversion factor of $CO_2$ for fuels, and fuel consumption.

• Journal of Biosystems Engineering
• /
• v.6 no.2
• /
• pp.20-32
• /
• 1982

This survey was conducted to investigate the present status of farm tractor utilization for obtaining a basic reference to the establishment of the government's agricultural mechanization strategies. Thirty two counties from the eight provinces except Jeju were covered in this study. From these selected areas, 433 sample farms having farm tractor were taken to obtain the general informations by the enquete, and 93 sample farms among them to investigate the status of daily tractor use in the year of 1980. The analyzed results are summarized as follows: 1. Farm tractors owned by the rice-oriented farms holds 71.5 percent of the total number of tractors the livestock-oriented farms 17.0 percent, and the orchard-oriented farms 7.0 percent. Among the farm tractors 64.3 percent was a large size (46ps) and 35.7 percent a small size(19~23ps). 2. Most of the tractors surveyed were equipped with the essential attachments such as plow and rotavator. About 18 percent of the tractor owners had no trailer, which seemed too high considering the large percentage of tractor use for transportation. The availability of other attachments was very low except a grader on the rice-oriented farms and a hay harvester and a front loader on the livestock-oriented farms. 3. The average size of farm was 3.9 hectare for the rice-oriented farms, 13.9 hectare for the livestock-oriented farms and 7.4 hectare for the orchard-oriented farms. It was obious that the average farm size of was too small compared to the theoretical machine capacity of the tractors. 4. About 70 percent of the tractor operators were in the age of twenties and thirties. About 90 percent of them had an educational level of middle school graduate or above even though their technical level was very low. 5. Any particular problem in tractor use was not found in this survey. From the farmer's preference for purchasing a new tractor, however, it is estimated the demand on a 20-30ps tractor will be more increased. 6. The average annual use of tractor was of about 100 days or 400 hours. It appeared that the rice-oriented farms used most with 412.4 hours per year, and followed by the livestock-oriented farms with 403.6 hours, the orchard oriented farms with 377.7 hours. 7. Among the total hours of tractor use, 47.3 percent was for transportation, and 41.6 percent was for plowing and rotary tillage. The largest portion of the annual tractor use was taken by transportation on the livestock-oriented farms, by land preperation on the rice-oriented farms, and by loading and chemical spraying on the orchard-oriented farms. 8. The hours of tractor use had a peak in May. The hours of use for own farm was remarkably different among the different farm oriented, but there was no considerable difference between the too different sizes of tractor. 9. The hours of tractor use decreased as the age of the operator or the educational level increased. The reason might be that the operators who had a high educational level or were older had a tendency of disliking custom works. 10. The average custom use of tractor was 171.3 hours per year, and the ratio of custom work was 63.7 percent on the rice-oriented farms, 31.7 percent on the livestock-oriented farms and 22.4 percent on the orchard-oriented farms. Among the custom works, the most popular one was the grader leveling. 11. The charge on custom work was about 40,000 Won per hectare for plowing and rotary tillage, and it was the most expensive in the southeastern region, and next followed by the southwestern region. 12. The average plowing capacity of the small tractor was 7.8 hours per hectare in the paddy field, and that of the large tractors was 4.3 hours per hectare. The average rotary-tilling capacities of the small and the large tractors were 6.5 and 4.3 hours per hectare, in the paddy field respectively.