• Journal of the Korean Geotechnical Society
• /
• v.32 no.10
• /
• pp.31-40
• /
• 2016

In order to investigate the change in soil arch structure developed within the soil subjected to trapdoor movement, various responses in the deformed particle assembly were observed via photoelastic measurement technique. The particle assembly was composed of the regularly stacked model particles coated by thin photoelastic material. Variation of the internal structure transmitting contact forces were observed by taking images showing the photoelastic responses and compared with the change in slip lines and pressures measured by load cells placed beneath the assembly. Initial soil arch structure established immediately after the trapdoor movement collapsed progressively and meanwhile a new extended structure was developed against further movement of the trapdoor. For the sufficient movement of the trapdoor, initially identical regions bounded by the soil arch structure and slip lines were separated and the region enclosed by slip lines became a part of the region loosing the transmitting contact forces identified by photoelastic measurement.

• Korean Chemical Engineering Research
• /
• v.53 no.2
• /
• pp.131-136
• /
• 2015

The nanostructural graphene/vanadium oxide (graphene/$V_2O_5$) composite with enhanced capacitance was synthesized by the electro-deposition in 0.5 M $VOSO_4$ solution. The morphology of composites was characterized using scanning electron microscopy (SEM), x-ray diffraction pattern (XRD), and x-ray photoelectron spectroscopy (XPS). The oxidation states of the electro-deposited vanadium oxide was found to be $V^{5+}$ and $V^{4+}$. The morphology of the prepared graphene/$V_2O_5$ composite exhibits a netlike nano-structure with $V_2O_5$ nanorods in about 100 nm diameter, which could lead a better contact between electrolyte an electrode. The composite with a deposition time of 4,000 s exhibits the specific capacitance of $854mF/cm^2$ at a scan rate of 20 mV/s and the capacitance retention of 53% after 1000 CV cycles.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.4
• /
• pp.25-32
• /
• 2001

A microwave vacuum (MW/V) dryer was developed for drying short roundwoods, from which woodcraft souvenirs in Korean market are mostly made, and which were hardly dried without defects in a conventional kiln. It consisted of three 1.5 kW magnetrons of 2,450 MHz, a vacuum pump, a load cell of 100 kg and a cavity of $580{\times}580{\times}1,360\;mm^3$. A computer program was developed to switch on or off the magnetrons according to drying schedules, those were based on microwave injection time or the average of wood temperatures. To evaluate the new MW/V dryer the roundwood specimens of rigida pine, poplar and birch were dried. Their log diameters and lengths ranged from 125 to 25 em and from 25 to 50 cm, respectively. In spite of the presence of minor drying defects, the MW/V drying is found to be an effective method for drying short roundwoods. Wooden turneries made of red alder and ash logs were also MW/V dried from green to 4%MC without any degradation. The rates of the MW/V drying were examined for three different lengths of poplar logs.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.6
• /
• pp.1723-1730
• /
• 2014

The use of strand wire in structure has been increased by the recent development of construction technologies. Until now, in spite of difficult problems in measuring strand stresses within PSC girders, indirect estimation with a load cell or accelerometer has been often used. In this paper, the electrical resistance strand meter for effective measurement of strand stresses is proposed with experiments considering material, location and thickness of sensor. The reliability and feasibility of the strand meter is enhanced through the experiment with 29.9m PSC girder.

• Journal of the Korea Convergence Society
• /
• v.9 no.2
• /
• pp.303-311
• /
• 2018

Squat exercise is one of the free weight exercises that are recognized as important from a bio-mechanical point of view. It is an important exercise to train lower extremity muscles in daily activities or sports activities and to strengthen trunk and lower body strength. It is effective and accurate to use a variety of assistive devices to calibrate athletic posture with squat exercise supported interactive device. The issues of the structural analysis for design a foot plate for squat exercise is to model the behavior by simplifying the dynamic behavior. In this paper, the authors proposed a exercise system design method for the vertical load distribution and bio-mechanical signal process used for the squat exercise mechanism analysis, and based on these results, designed device can make the more safe and reliable free weight exercise. It is applied to system design through design method with kinematic dynamic, VR device and estimation model of exercise.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.117-120
• /
• 2008

Recently, according to the increasement of high-rise building construction and domestic situation, requirements of rapid cycle construction are increasing. For more economical and rapid cycle construction, it is required to reduce formwork cost. So formwork have to be stripped as soon as possible. But as fresh concrete is loaded with construction load, it is likely that the structure will have problems with safety and serviceability. To reduce construction cycle economically, safety and serviceability of structure against construction load have to be considered. But as behavior of structure under construction is so complicated, behavior of structure has to be investigated according to construction stage. Therefore, through field instrumentation of apartment, behavior of structure under construction was analyzed.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.3
• /
• pp.287-294
• /
• 2008

This study proposes a novel method for in service evaluation of tension force of a prestressed 7-wire strand which is frequently employed for retrofitting bridge superstructure. The smart strand is made by replacing the straight king wire of the strand with an instrumented steel tube in which the FBG sensor is embedded. Since the strain of the smart strand can easily be measured using the sensor, it is possible to monitor tension force of the strand during the service. For the sake of demonstrating effectiveness of the proposed strand, we came up with a 7.0m long prototype with 2 FBG sensors, and it is applied as an external tendon to a 6.4m long and 0.6 high RC T-shaped beam. A loading-unloading test has been carried out, and estimated tension forces using the smart strand are compared with measured forces by load cell. The comparison showed that the proposed smart tendon is useful and accurate for monitering tension force of the prestressed tendon.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.1089-1093
• /
• 2010

최근 하천의 자연성 및 생태기능의 향상을 위해 매트류 호안공법의 적용이 증가하고 있다. 이러한 공법이 적용된 호안은 강수 및 하천수의 지속적인 유입으로 인해 앵커핀과 비탈면 간의 마찰력을 저하시킬 수 있다. 마찰력의 저하는 앵커핀의 고정능력을 저하시켜 매트가 들뜨는 현상을 발생시키고, 이로 말미암아 비탈면에 식재된 식생의 고사는 물론 비탈면의 슬라이딩 현상의 발생에 의해 비탈면 붕괴에 까지 이르게 하고 있다. 그러나 현재 호안매트와 함게 시공하는 앵커핀의 적용에 대한 구체적인 기준과 연구가 미흡한 실정이다. 본 연구에서는 매트류 호안제품을 비탈면에 고정시키는 목적으로 사용하고 있는 앵커핀에 대한 인발특성을 파악하고자 하였다. 인발실험에 사용된 앵커핀은 실제 하천호안에 적용되고 있는 상용제품으로 형태가 다른 4가지 type을 실험에 사용하였으며, 앵커핀의 관입깊이(170mm, 250mm) 별로 인발실험을 실시하였다. 실험에 사용된 인발장치는 인발부에 로드셀을 장착하여 앵커핀과 결합이 가능하도록 하였으며, 인발시 발생하는 계측 값을 컴퓨터를 통해 출력이 가능하도록 제작하였다. 실험결과 4가지 형태의 앵커핀에 대한 관입깊이별 형태별 인발특성을 파악할 수 있었으며, 비탈면 및 매트의 고정효과가 우수한 앵커핀의 형태에 대해서도 파악할 수 있었다. 관입깊이별 최대 인발력은 두 변위(170mm, 250mm) 모두 Type 4가 337N, 594N 으로 가장 큰 인발력을 가지는 것으로 측정되었으며, 변위에 의한 인발력의 증가는 Type 2가 138%로 가장 큰 폭의 증가 값을 보였다. 또한 토양과 앵커핀의 마찰력 향상을 위해 하부가 돌출된 형태로 제작된 Type 2와 Type 4가 상대적으로 실험 후반부에서 최대 인발력이 발생하고 인발지속시간이 길게 나타나는 것으로 볼 때, 인발저항은 앵커핀 하부의 돌출면적에 영향을 받는 것으로 판단된다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.5 s.120
• /
• pp.465-470
• /
• 2007

The co-channel interference is a primary factor of loss in multimedia mobile communications. In this paper, we present a performance of the frequency reuse partitioning to refrain the co-channel interference and maximize system performance. First, we analyze the co-channel interference using the frequency reuse partitioning through the statistical modeling. From this results, we decide on the frequency reuse partitioning for the system throughput which is maximized. Finally, analysis and simulation results show that the frequency reuse partitioning based cellular system can mitigate the co-channel interference and maximize the system throughput. The experimental results show that system throughput is maximized from 0.7 to 0.8 according to traffic road. We can maximize the system throughput using the results with cellular system design parameter.

• Journal of Sensor Science and Technology
• /
• v.12 no.5
• /
• pp.199-204
• /
• 2003

This paper describes on the fabrication and characteristics of a ceramic thin-film pressure sensor based on Ta-N strain-gauges for harsh environment applications. The Ta-N thin-film strain-gauges are sputter-deposited onto a micromachined Si diaphragms with buried cavity for overpressure protectors. The proposed device takes advantages of the good mechanical properties of single-crystalline Si as diaphragms fabricated by SDB and electrochemical etch-stop technology, and in order to extend the operating temperature range, it incorporates relatively the high resistance, stability and gauge factor of Ta-N thin-films. The fabricated pressure sensor presents a low temperature coefficient of resistance, high-sensitivity, low non-linearity and excellent temperature stability. The sensitivity is $1.097-1.21\;mV/V{\codt}kgf/cm^2$ in the temperature range of $25-200^{\circ}C$ and the maximum non-linearity is 0.43%FS.