• Journal of the Korean Electrochemical Society
• /
• v.15 no.1
• /
• pp.12-18
• /
• 2012

The prohibitively high cost of Pt catalyst might be the biggest barrier for the commercialization of proton exchange membrane fuel cells (PEMFC) of which wide application is expected. Worldwide research efforts for the development of alternative to Pt oxygen reduction reaction (ORR) catalyst are made recently. One of the important considerations in the catalyst development is durability issue as well as economic aspect. From this point of view, platinum group metals (PGM) except Pt can be a candidate for replacing Pt catalyst because the material properties and the catalytic activity of PGM are expected to be similar to Pt. In contrast to Ir, Rh and Os to which not so much attention has been paid as an ORR catalyst, Pd that is most similar to Pt in terms of material properties and catalytic activity and Ru that is in the form of chalcogenide have been studied intensively. Activity comparison between non-Pt and Pt oxygen reduction catalysts by half cell test using RDE (rotating disk electrode) or PEMFC MEA (membrane electrode assembly) operation indicates that Pd-based catalysts show the most similar activity to Pt. In this paper we analyze the composition of PGM ORR catalyst in literature to promote the development of non-Pt ORR catalyst.

• Resources Recycling
• /
• v.27 no.3
• /
• pp.93-99
• /
• 2018

Effective extraction of platinum group elements by dissolving waste platinum scrap from the display industry and solvent extraction, was studied. The extracted platinum solution was prepared as a precursor solution for diesel automotive exhaust gas purification catalyst and its catalytic activity was tested. The behavior of aqueous species of platinum was investigated through solution chemistry and based on the existence and behavior of these chemical species, the possibility of extraction and separation was established. By dissolving waste scrap by electrochemical method, the dissolution time of scrap was shortened and the extraction efficiency was increased. Through separation and removal of rhodium component, solvent extraction by TBP, and stripping by hydrochloric acid, Pt-Chloride-$H_2O$ solution was prepared. And then, an platinum amine complex solution through amination reaction with this solution as a raw material was prepared. The possibility of producing high-value platinum compounds from platinum group waste scrap was investigated by preparing platinum amine complex solution and then examining the catalytic activity with this amine precursor on the combustion reaction of carbon black.

• Journal of the Korean Vacuum Society
• /
• v.17 no.3
• /
• pp.234-239
• /
• 2008

Tungsten and rhodium target tube for a 40 kV x-ray transmission anode was developed to apply to the hand-held XRF(X-Ray Fluorescence) apparatus and its characteristics were evaluated. From the measurement of the energy distribution and dose of x-ray, it was confirmed that our results were good agreements with the known ones. The optimum thickness of metal film deposited on Be window to extract the maximum dose were $2.6{\mu}m$ and $2.7{\mu}m$ in case of W-target tube and Rh-target tube, respectively. When it was continuously worked during 30 min. at 40 kV in tube voltage and at $60{\mu}A$ in tube current, the temperature at target did not exceed $50^{\circ}C$. Our results reveals that the 40 kV x-ray transmission anode tube can be applied to the hand-held XRF apparatus.

• Journal of the Korean Vacuum Society
• /
• v.17 no.3
• /
• pp.247-252
• /
• 2008

By using the transmission anode x-ray tube developed to apply to the hand-held XRF equipment, we carried out XRF experiment and evaluated the influences of the x-ray tube on XRF spectra. XRF data, which is measured using the W-target and Rh-target tube, were good agreements with the known results. FWHM of Fe $K_{\alpha}$-line measured by W-target tube with the 35 kV-tube voltage and the $40{\mu}A$-tube current was 180 eV. This result reveals that our XRF equipment using the transmission anode x-ray tube is enough for a qualitative analysis of materials. By comparison XRF data with the integrated intensity of x-ray tube, it was confirmed that Rh-target tube is better than W-target tube for application to the hand-held XRF equipment.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.3
• /
• pp.138-145
• /
• 2011

Diesel particulate filter (DPF) systems are being used to reduce the particulate matter emission of diesel vehicles. The DPF should be regenerated after certain driving hours or distance to eliminate soot in the filter. The most widely used method is active regeneration with oxygen at $550{\sim}650^{\circ}C$. Syngas (synthetic gas) can be used to lower the regeneration temperature of Catalyzed DPF (CDPF). The syngas is formed by fuel reforming process of CPOx (Catalytic Partial Oxidation) at specific engine condition (1500rpm, 2bar) using 1wt.% $Rh/CeO_2-ZrO_2$ catalyst. The oxidation characteristics of PM with syngas supplied to filter were studied using partial flow system that can control temperature and flow rate independently. The filter is coated with washcoat loading of $25g/ft^3$ $Pt/Al_2O_3-CeO_2$, and multi-channel CDPF (MC-CDPF) was used. The filter regeneration experiments were performed to investigate the effect of syngas exothermic reaction on soot oxidation in the filter. For this purpose, before oxidation experiment, PM was collected about 8g/L to the filter at engine condition of 1500rpm, bmep 8bar and flow temperature of $200^{\circ}C$ Various conditions of temperature and concentration of syngas were used for the tests. Regeneration of filter started at 2% $H_2$ and CO concentration respectively and inlet temperature of $260^{\circ}C$. Filter Regeneration occurs more actively as the syngas concentration becomes higher.

• Analytical Science and Technology
• /
• v.13 no.6
• /
• pp.781-788
• /
• 2000

Tellurium in simulated nuclear spent fuels (SIMFUEL) has been determined by hydride generation-inductively coupled plasma atomic emission spectrometry (HG-ICP-AES). Parameters such as concentrations of HCl and $NaBH_4$, flow rate of HCl and $NaBH_4$ were optimized and then the effects of U, Mo, Pd, Rh and Ru on the Te intensity were investigated. A thiourea as a masking agent was used to eliminate or minimize such interferences specially caused by palladium. Tellurium was measured by HG-ICP-AES and ICP-MS after separation of tellurium from SIMFUEL with cation exchange chromatography. The relative deviation between direct measurement and separation method was less than 6% based on the data by ICP-MS.

• Journal of Radiation Protection and Research
• /
• v.38 no.2
• /
• pp.78-90
• /
• 2013

Recently, the interest on exposure to radiation is rising. The radiation exposure of mammography is higher in absorbed dose than of X-ray, therefore unnecessary exposure needs to be reduced, and higher image quality is needed. Generally, ray quality of the radiation imaging is an important factor that determines image quality and the amount of ray exposure, and they are affected by tube voltage and added filter. The X-ray energy that is exposed from mammography device is generally a continuous spectrum, which includes low energy that has minute influence on the image quality, and high energy that hinders contrast on image. Currently, molybdenum (Mo) and rhodium (Rh) are the most used added filters for mammography device, and they are used differently according to the energy region of X-ray. This study aims to find out the degree of reduction in exposure dose according to the thickness of aluminum (Al), and to study the changes in image quality and dose when the added filter plates that are made with niobium (Nb) or zirconium (Zr) are used, other than molybdenum (Mo) and rhodium (Rh), the two most used added filters that have similar atomic number and K-absorption regions as Nb and Zr. In this study, single-added filters of molybdenum (Mo), niobium (Nb), and zirconium (Zr) are used, and in some cases, Aluminum (Al) is combined with the single filters. In this case, image quality is considered to be improved depending on the type of added filters, and by using Aluminum (Al) filter together with the others, unnecessary X-ray of low energy would be absorbed, therefore the dose is expected to decrease without any influence when the concentration level becomes identical.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.7
• /
• pp.464-471
• /
• 2013

In this study, the resource efficiency and future metal resource requirement in photovoltaic (PV) production system were evaluated by using material balance data and life cycle assesment (LCA) method. As a result, in the resource efficiency of ferrous and non-ferrous metal, lead and tin had higher resource efficiency than other materials in all PV systems (SC-Si, MC-Si, CI(G)S, CdTe). In the resource efficiency of rare metals, gallium and rhenium in silicon system and rhenium and rhodium in thin-film system ranked as the first and second high resource efficiency. In case of rare earth metal, gadolinium and samarium took higher resource efficiency. The results of the future metal resource requirement in PV systems showed that 2,545,670 ton of aluminium, 92,069 ton of zinc, 22,044 ton of copper, 1,695 ton of tin and 31 ton of nickel will be needed by 2030 in South Korea, except resource recycling supplement.

• Analytical Science and Technology
• /
• v.11 no.2
• /
• pp.112-119
• /
• 1998

A Siemens SemiQuant (SSQ) 3000 program, a precalibrated 'standardless' analytical program handling up to 90 elements, was evaluated for the fast analysis of various types of reference materials using a wavelength dispersive X-ray spectrometer. Various types of standard reference materials such as metal discs, metal chips, and geological materials in powder form were analysed and it took 23 minutes of measuring time for 75 elements. Measurements of geological reference materials using different sampling methods were carried out and their data were interactively evaluated. The analysis of materials of a known matrix concentration such as stainless steels provided higher precision value compared to totally unknown samples. The analyses of materials prepared as pressed pellets or fused glass beads provided higher precision values compared to the measurement of loose powders with a foil on the sample surface and helium operation, though their sampling procedures were more complicate and took more time. Since very light elements such as boron, carbon, and oxygen have a strong influence on the matrix effects and also on the calculation of effective matrix corrections, the rhodium Compton check was applied to verify the reliability of the defined light element concentrations of light matrix materials and the defined major sample compounds. Failure of defining correct matrix resulted in an unoptimized matrix correction and therefore in the wrong calculation of the element concentration.

• Journal of the Korean Chemical Society
• /
• v.33 no.5
• /
• pp.516-521
• /
• 1989

Reaction between the $N_2O_2-type$ tetradentate ligand, ethylenediamine-N,N'-di-S-${\alpha}$-isobutylacetic acid (SS-emiba) and $RhCl_3{\cdot}3H_2O$ has yielded ${\Delta}-s-cis-\;and\;{\wedge}-uns-cis-[Rh(SS-eniba)Cl_2]-$. ${\Delta}-s-cis-[Rh(SS-eniba)Cl_2]^-$ has been utilized to react with S-methyl-L-cystcine(Smc) to give ${\Delta}-s-cis-[Rh(SS-eniba(Smc)]^+$. The oxidation of ${\Delta}-s-cis-[Rh(SS-eniba(Smc)]^+$ using $H_2O_2$ has produced ${\Delta}-s-cis-[Rh(SS-eniba)(Smc-o)]^+$, in which the coordinated sulfur has been converted into the sulfoxide group. In a separate series of experiments the S-methyl-L-cysteine is oxidized by $H_2O_2$ to give S-methyl-L-cysteine sulfoxide, which is then coordinated to ${\Delta}-s-cis-[Rh(SS-eniba)Cl2]^-$ to make the standard complet of ${\Delta}-s-cis-[Rh(SS-eniba)(Sme-o)]+$ for comparison with the complex obtained from the oxidation of ${\Delta}-s-cis-[Rh(SS-eniba)(Smc)]^+\;by\;H_2O_2.$