• Korean Journal of Optics and Photonics
• /
• v.32 no.3
• /
• pp.108-113
• /
• 2021

We propose and experimentally demonstrate a method of remote sound extraction using laser Doppler interferometry. The output frequency of a laser Doppler interferometer changes to be the same as the frequency of the acoustic wave from than object vibrated by the sound due to the Doppler effect. Based on this phenomenon, we measure the vibrational frequency of a remote target affected by a sound wave in real time, via laser Doppler interferometry. We track the peak frequency of the interferometer's output via appropriate signal processing, which confirms that the characteristics of the so detected wave are the same as that of the original sound source. We also confirm that the same method can retrieve the sound waves not only from remote sources of single tones, but from those of any sound.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.10
• /
• pp.1900-1907
• /
• 1992

This paper presents the vibration mode, natural frequencies and amplitudes of the circular plate due to the changes of the boundary conditions by varying free arc angles. The vibration mode, amplitudes and natural frequencies of the circular plate are obtained by time-average holographic interferometry and laser doppler vibrometer. The vibration modes of the circular plate with the mixed boundary conditions are found from the 1st mode to the 4th mode. The curve shapes of the natural frequency ratios obtained from this study are in a good agreement with other results obtained by numerical analysis. The displacement curves obtained from time average holographic interferometry and laser doppler vibrometer agree well in case of large amplitude, but show a little difference in case of small amplitude.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.982-982
• /
• 2005

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2560-2567
• /
• 2000

When spatially dense velocity distribution is measured by a scanning laser Doppler vibrometer, the Fourier transform method provides the real and imaginary parts of the mode shapes in the form of a polynomial. However the Fourier transform method is often impractical because the independent decomposition property of cosine and sine components into real and imaginary parts, respectively, does not hold due to the leakage problem which commonly occurs in the Fourier transform of harmonic signals. To deal with this problem, a Hilbert transform method is newly proposed in this article. The proposed method is free from the leakage problem and relatively robust to the scanning error. A simulation example is provided to verify the effectiveness of this method.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.670-675
• /
• 2003

With the increase in recording density and higher rotation speeds, the aerodynamic aspect of hard disk drives (HDDs) is now quite significant. To achieve high TPI (tracks per inch) for hard disk drives, the actuator must induce less air turbulence. Also, alternative cross sections for the actuator arms are proposed for the reduction of air turbulence. In this study, off-track vibration of actuator arms used in of 3.5" hard disk drives with different cross sections have been measured by using Laser Doppler Vibrometer (LDV). It has been found that the vibration of the actuator arms with modified cross sections is lower than the conventional one.

• Korean Journal of Optics and Photonics
• /
• v.11 no.5
• /
• pp.306-311
• /
• 2000

This paper deals with the development of Laser Doppler Vibrometer (LDV) that can mea~ure the tlequency and amphlude of the ultrasonic vibralion. Hc-Ne laser (632.8 om) is used as a light source, and Michelson interferometer in winch frequency of the objective beam is shIfted by Bragg cell IS adopted The frequency modulated signal centered at 40 MHz flom the PIN diode IS amplified. down-col1vel1ed to 2.5 MHz, filtered and digiLized. The voltage output that is proportional to the velocity of the vibratwg surface is obtawed using digItal PLL. A microprocessor is used to extract the frequcncy aud amplitude of the vibratIOn from the voltage output. It is found that the developed LDV can measure up to 300 kHz vibratIOn and the mlillmUITI measurable amplitude is I nm at 300 kHz. We believe thatlhis LDV can be used to measure the vibratIOn of the heavy electric maclllnery and micro-size structures. tures.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.53-55
• /
• 2001

A dual probe laser Doppler vibrometer (LDV) that has one laser source and provides two independent object beams has been developed for the first time. An electronic circuit that converts light signal to electronic signal has been also developed using phase locked loop(PLL). It was found that this types of dual probe LDV can be used in differential mode and self-vibration compensation mode.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1838-1840
• /
• 2001

A dual probe laser Doppler vibrometer (LDV) that has one laser source and provides two independent object beams has been developed for the first time. An electronic circuit that converts light signal to electronic signal has been also developed using digital phase locked loop(DPLL). It was found that this types of dual probe LDV can be used in differential mode and self-vibration compensation mode.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.484-490
• /
• 2008

For CSLDV, the Chebyshev demodulation (or polynomial) technique and Hilbert transform approach have been used for mode shape reconstruction with harmonic excitation. In this paper, the Hilbert-Huang transform approach was applied as an alternative to impact excitation cases in terms of a numerical approach. The vibration of the tested structure is modeled using impulse response functions. In order to verify this technique, a simply supported beam was chosen as the test rig. With additional innovative steps which are the ideal-band pass filter and the nodal point determination, Hilbert-Huang transformation can be used for a good mode shape reconstruction even in the impact excitation case.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.414-419
• /
• 2003

There are some methods fur extracting mode shapes from a continuously scanned data such as a modulation, Chebyshev polynomial, and Hilbert approach. In this paper, Chebyshev and Hilbert approaches were investigated through the numerical experiment first. As some experimental parameters were altered with small quantities, data were checked and plotted. From those results, the effects of unexpected parameters will be configured. And then, it will be actually helpful to select the proper method for specific testing environments.