• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.3 s.345
• /
• pp.40-47
• /
• 2006

The finite-field multiplication can be applied to the elliptic curve cryptosystems. However, an efficient algorithm and the hardware design are required since the finite-field multiplication takes much time to compute. In this paper, we propose a radix-4 systolic multiplier on $GF(2^m)$ with comparative area and performance. The algorithm of the proposed standard-basis multiplier is mathematically developed to map on low-cost systolic cells, so that the proposed systolic architecture is suitable for VLSI design. Compared to the bit-parallel, bit-serial and systolic multipliers, the proposed multiplier has relatively effective high performance and low cost. We design and synthesis $GF(2^{193})$ finite-field multiplier using Hynix $0.35{\mu}m$ standard cell library and the maximum clock frequency is 400MHz.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.6
• /
• pp.18-26
• /
• 1999

This paper presents the architecture and design of a DSSS MODEM ASIC chip for wireless local area networks (WLAN). The implemented MODEM chip supports the DSSS physical layer specifications of the IEEE 802.11. The chip consits of a transmitter and a receiver which contain a CRC encoder/decoder, a differential encoder/decoder, a frequency offset compensator and a timing recovery circuit. The chip supports various data rates, i.e., 4,2 and 1Mbps and provides both DBPSK and DQPSK for data modulation. We have performed logic synthesis using the $SAMSUNG^{TM}$ $0.6{\mu}m$ gate array library and the implemented chip consists of 53,355 gates. The MODEM chip operates at 44MHz, the package type is 100-pin QFP and the power consumption is 1.2watt at 44MHz. The implemented MODEM architecture shows lower BER compared with the Harris HSP3824.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.5
• /
• pp.31-40
• /
• 2010

This paper describes a LDPC decoder for IEEE 802.11n wireless LAN standard. The designed processor supports parity check matrix for block length of 1,944 and code rate of 1/2 in IEEE 802.11n standard. To reduce hardware complexity, the min-sum algorithm and layered decoding architecture are adopted. A novel memory reduction technique suitable for min-sum algorithm was devised, and our design reduces memory size to 25% of conventional method. The LDPC decoder processor synthesized with a $0.35-{\mu}m$ CMOS cell library has 200,400 gates and memory of 19,400 bits, and the estimated throughput is about 135 Mbps at 80 MHz@2.5v. The designed processor is verified by FPGA implementation and BER evaluation to validate the usefulness as a LDPC decoder.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.5
• /
• pp.94-99
• /
• 2010

This paper presents a design procedure of digitally controlled oscillator(DCO) for power optimization. By controlling coarse tuning bits and fine tuning bits of DCO, the proposed design procedure can optimize the power dissipation and does not affect the LSB resolution, frequency range, linearity, portability. For optimization, the relationship between control bits and power dissipation of the DCO was analyzed. The DCO circuits using and unusing proposed design technique have been designed, simulated and proved using 0.13um, 1.2V CMOS library. The DCO circuit with proposed design technique has operation range between 283MHz and 1.1GHz and has 1.7ps LSB resolution and consumes 2.789mW at frequency of 1GHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.3
• /
• pp.55-61
• /
• 2000

This paper presents an efficient hardware architecture of frame memory interface in MPEG-2 video encoder. To reduce the size of memory buffers between SDRAM and the frame memory module, the number of clocks needed for each memory access is minimized with dual bank operation and burst length change. By allocating the remaining cycles not used by SDRAM access, to the random access cycle, the internal buffer size, the data bus width, and the size of the control logic can be minimized. The proposed architecture is operated with 54MHz clock and designed with the VT $I^{тм}$ 0.5 ${\mu}{\textrm}{m}$ CMOS TLM standard cell library. It is verified by comparing the test vectors generated by the c-code model with the simulation results of the synthesized circuit. The buffer area of the proposed architecture is reduced to 40 % of the existing architecture.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.6
• /
• pp.459-468
• /
• 2003

This paper proposes a novel low-cost and high-speed Reed-Solomon (RS) decoder based on a new degree computationless modified Euclid´s (DCME) algorithm. This architecture has quite low hardware complexity compared with conventional modified Euclid´s (ME) architectures, since it can remove completely the degree computation and comparison circuits. The architecture employing a systolic away requires only the latency of 2t clock cycles to solve the key equation without initial latency. In addition, the DCME architecture using 3t＋2 basic cells has regularity and scalability since it uses only one processing element. The RS decoder has been synthesized using the 0.25${\mu}{\textrm}{m}$. Faraday CMOS standard cell library and operates at 200MHz and its data rate suppots up to 1.6Gbps. For tile (255, 239, 8) RS code, the gate counts of the DCME architecture and the whole RS decoder excluding FIFO memory are only 21,760 and 42,213, respectively. The proposed RS decoder can reduce the total fate count at least 23% and the total latency at least 10% compared with conventional ME architectures.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.7
• /
• pp.29-35
• /
• 2017

This paper presents a high-throughput area-efficient mixed-radix fast Fourier transform (FFT) processor using the efficient scheduling schemes. The proposed FFT processor can support 64, 128, 256, and 512-point FFTs for orthogonal frequency division multiplexing (OFDM) systems, and can achieve a high throughput using mixed-radix algorithm and eight-parallel multipath delay commutator (MDC) architecture. This paper proposes new scheduling schemes to reduce the size of read-only memories (ROMs) and complex constant multipliers without increasing delay elements and computation cycles; thus, reducing the hardware complexity further. The proposed mixed-radix MDC FFT processor is designed and implemented using the Samsung 65nm complementary metal-oxide semiconductor (CMOS) technology. The experimental result shows that the area of the proposed FFT processor is 0.36 mm2. Furthermore, the proposed processor can achieve high throughput rates of up to 2.64 GSample/s at 330 MHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.10C
• /
• pp.963-972
• /
• 2002

An 8192-point pipelined FFT/IFFT processor core is designed, which can be used in multi-carrier modulation systems such as DUf-based VDSL modem and OFDM-based DVB system. In order to improve the signal-to-quantization-noise ratio (SQNR) of FFT/IFFT results, two-step convergent block floating-point (TS_CBFP) scaling is employed. Since the proposed TS_CBFP scaling does not require additional buffer memory, it reduces memory as much as about 80% when compared with conventional CBFP methods, resulting in area-and power-efficient implementation. The SQNR of about 60-㏈ is achieved with 10-bit input, 14-bit internal data and twiddle factors, and 16-bit output. The core synthesized using 0.25-$\mu\textrm{m}$ CMOS library has about 76,300 gates, 390K bits RAM, and twiddle factor ROM of 39K bits. Simulation results show that it can safely operate up to 50-㎒ clock frequency at 2.5-V supply, resulting that a 8192-point FFT/IFFT can be computed every 164-${\mu}\textrm{s}$. It was verified by Xilinx FPGA implementation.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.45 no.2
• /
• pp.41-47
• /
• 2008

Most of media compression CODECs adopts the variable length coding method. This paper proposes special registers and instruction set for bit stream process in order to accelerate the decoding process of the variable length code. The instruction set shares the conventional data path to minimize additional costs. And bit stream is read from the memory instead of the special port. Therefore the instruction set minimizes the change of the processor, and is adopted without any additional input controller and buffer, and accelerate decoding process of variable length code. The data path of the instruction set needs additional 65 bits memory and 344 equivalent gates, 0.19 ns delay under TSMC $0.25{\mu}m$ technology. The instruction set reduced the execution time of the variable length code decoding process in H.264/AVC by about 55%.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.171-171
• /
• 2017

전산유체역학(CFD: Computational Fluid Dynamics)를 이용한 스마트팜 환경 내부의 정밀 제어 연구가 진행 중이다. 시계열 데이터의 난해한 동적 해석을 극복하기위해, 비선형 모델링 기법의 일종인 인공신경망을 이용하는 방안을 고려하였다. 선행 연구를 통하여 환경 데이터의 비선형 모델링을 위한 Tensorflow활용 방법이 하드웨어 가속 기능을 바탕으로 월등한 성능을 보임을 확인하였다. 그럼에도 오프라인 일괄(Offline batch)처리 방식의 한계가 있는 인공신경망 모델링 기법과 현장 보급이 불가능한 고성능 하드웨어 연산 장치에 대한 대안 마련이 필요하다고 판단되었다. CFD 해석을 위한 Solver로 SU2(http://su2.stanford.edu)를 이용하였다. 운영 체제 및 컴파일러는 1) Mac OS X Sierra 10.12.2 Apple LLVM version 8.0.0 (clang-800.0.38), 2) Windows 10 x64: Intel C++ Compiler version 16.0, update 2, 3) Linux (Ubuntu 16.04 x64): g++ 5.4.0, 4) Clustered Linux (Ubuntu 16.04 x32): MPICC 3.3.a2를 선정하였다. 4번째 개발환경인 병렬 시스템의 경우 하드웨어 가속는 OpenCL(https://www.khronos.org/opencl/) 엔진을 이용하고 저전력 ARM 프로세서의 일종인 옥타코어 Samsung Exynos5422 칩을 장착한 ODROID-XU4(Hardkernel, AnYang, Korea) SBC(Single Board Computer)를 32식 병렬 구성하였다. 분산 컴퓨팅을 위한 환경은 Gbit 로컬 네트워크 기반 NFS(Network File System)과 MPICH(http://www.mpich.org/)로 구성하였다. 공간 분해능을 계측 주기보다 작게 분할할 경우 발생하는 미지의 바운더리 정보를 정의하기 위하여 3차원 Kriging Spatial Interpolation Method를 실험적으로 적용하였다. 한편 병렬 시스템 구성이 불가능한 1,2,3번 환경의 경우 내부적으로 이미 존재하는 멀티코어를 활용하고자 OpenMP(http://www.openmp.org/) 라이브러리를 활용하였다. 64비트 병렬 8코어로 동작하는 1,2,3번 운영환경의 경우 32비트 병렬 128코어로 동작하는 환경에 비하여 근소하게 2배 내외로 연산 속도가 빨랐다. 실시간 CFD 수행을 위한 분산 컴퓨팅 기술이 프로세서의 속도 및 운영체제의 정보 분배 능력에 따라 결정된다고 판단할 수 있었다. 이를 검증하기 위하여 4번 개발환경에서 운영체제를 64비트로 개선하여 5번째 환경을 구성하여 검증하였다. 상반되는 결과로 64비트 72코어로 동작하는 분산 컴퓨팅 환경에서 단일 프로세서 기반 멀티 코어(1,2,3번) 환경보다 보다 2.5배 내외 연산속도 향상이 있었다. ARM 프로세서용 64비트 운영체제의 완성도가 낮은 시점에서 추후 성공적인 실시간 CFD 모델링을 위한 지속적인 검토가 필요하다.