• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.794-798
• /
• 2002

This paper deals with a moving coil type linear motor for fast access of the miniature ODD. This slim-line motor is composed of the mover supported by guide mechanism, the coil wound into it, and the yoke attached to the permanent magnet for stator. The driving force is generated by the PM of the stator and the current in the coils of the mover. Magnetic circuit analysis and Finite Element Method are applied to estimate the thrust force at air gap. In order to compare the force characteristics between two methods, various experiment results are applied to verify on a prototype. Also the flexible modes of the motor are predicted through the FEM and the structural components are modified to locate this on high frequency region.

• Journal of KSNVE
• /
• v.11 no.2
• /
• pp.315-322
• /
• 2001

This paper is focused on the frictionally induced thermoelastic instability (TEI) in automotive disk brakes. This instability leads to the formation of localized high temperature contact regions known as hot spots. This article investigates the themoelastic instability in automotive disk brake systems consisting of a finite thickness layer (disk) and two half-planes (pads) using a perturbation method. The antisymmetric mode involves hot spots located alternately on two sides of the disk. As a result the circumferentially periodic hot spots produce rotor surface distortion and Induce low frequency vibration. Also the effects of system parameters on the critical speed for TEI are investigated.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.10
• /
• pp.1092-1098
• /
• 2009

The squeal propensity of an automotive disc brake system is studied in the theoretical and computational manner. The rotating disc is in contact with two stationary pads and the nonlinear friction is engaged on the contact surface. The friction-coupled equations of motion are derived in the finite element(FE) of the actual brake disc and pad. From the general definition of friction force, the rotation and in-plane mode effects can be included properly in the brake squeal model. The eigenvalue sensitivity analysis and the mode shape visualization at squeal frequencies are also conducted for the detailed investigation. It is found that the squeal propensity is strongly influenced by rotation effect and the in-plane mode can be involved in squeal generation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.207-211
• /
• 2009

To investigate the vibration characteristics of compact disc player(CDP) due to excited vibration and disturbances, it is necessary to consider the transmissibility of the CDP. The disturbances as well as the temperature in the vehicle are the one of the important factors when CDP is designed. In this study, the effect on the temperature of the oil damper, which is applied to anti-vibration system of the CDP, was investigated. When the temperature was changed from -30 to 90 and the properties of the oil damper (hardness of rubber, viscosity of oil) were changed, the transmissibility was measured.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2513-2519
• /
• 2000

Free vibration characteristics of an initially stressed CD/DVD disk, which is designed for increasing critical speeds of current optical disks, are analyzed using the Rayleigh-Ritz technique based on variational formulations. Natural frequencies of the new disk depend on membrane stresses caused by disk rotation as well as residual stresses imposed during the cooling process of the injection molding. Critical speeds are calculated for the various initial patterns of radial and circumferential stresses. Initially imposed tensile stresses increase the natural frequencies of all the vibration modes except zero nodal diameter mode, whose natural frequency is independent of circumferential stress. A new disk with initial tensile stress of 0.5MPa is shown to have its critical speed about 30 % higher than the current optical disk.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.359.2-359
• /
• 2002

To satisfy operation condition in information storage device, the suspension shape is very important since it correlates to dynamic characteristics. Therefore, it is necessary to analyze the dynamic characteristics by using finite element analysis, shape optimization. The suspension has various modes according to different kinds of frequency bandwidth. Sway mode and second torsion mode are especially critical among them. (omitted)

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.10 s.103
• /
• pp.1169-1176
• /
• 2005

In this study, experimental tests for driving noise of various optical disk drives (ODD) have been performed using 1/2' microphone noise measurement system. Several new and old ODD models by different manufacturers are practically considered and compared for realistic driving conditions. Sound insulation case with absorbing material for the present experimental tests is designed and constructed using CATIA system. It is found that average data transfer rate, operating RPM, and sound noise level seem to be different for the ODD models with same denoted speed by different manufacturers. Moreover, driving sound noise level can be largely affected by both tray shape and driving speed even for the condition of the same apparent data transfer rate.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.11
• /
• pp.1075-1082
• /
• 2004

This research demonstrates the shock response analysis of a head disk assembly subjected to a half-sine shock pulse in the axial direction. In case of disk analysis, the numerical method presented by Barasch and Chen is used. Galerkin method is used with mode shape by numerical method. Head-suspension system is modeled as the cantilever in order to get simulation results. Simulation results of HDA are calculated by Runge-Kutta method. Finally, shock responses of head and disk are analyzed according to the change of the rotating speed of the disk.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.565-570
• /
• 2001

대상 기계구조물의 유한요소 모델로부터 구한 해석결과가 실험결과와 오차를 나타낼 때, 이러한 오차를 줄일 수 있도록 유한요소 모델의 변경이 요구된다. 유한요소 모델개선은 이러한 역문제(Inverse Problem)를 다루는 체계적인 접근법이다. 일반적으로 유한요소 모델에서 변경할 수 있는 매개변수의 개수는 실험결과의 개수보다 많으므로 실험결과와 일치되는 개선된 유한요소 모델은 무한하다고 할 수 있다. 그러나, 개선된 유한요소 모델이 물리적 타당성을 갖도록 매개변수의 변경량에 제한을 주면 일반적으로 초기 유한요소 모델에 비해 실험결과와의 오차가 개선된 근사해만 존재하게 된다. 따라서, 모델개선 과정을 통해 구한 개선된 모델은 오차의 평가기준 또는 목적함수에 따라 정해진 다양한 근사해 중 하나이다. 기존의 모델개선 방법에서는 단 하나의 오차 평가기준 또는 목적함수를 사용하고 이를 최소화 하는 모델을 구한다. 개선된 모델을 구하기 이전에는 사용된 평가기준이 타당한지 검토할 수 없으므로 대부분의 경우, 시행착오법으로 목적함수를 설정하게 된다. 본 논문에서는 다목적 최적화 기법을 이용한 오차 평가기준을 소개하고 이를 하드디스크커버 유한요소 모델개선에 응용한다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.6
• /
• pp.606-611
• /
• 2008

Consumer's product selection measures are being shifted from the units' operational performance to overall performance. Low noise, low vibration, and low power consumption rate, etc. which used to be additional quality indices, now become vital performance factors. Especially, noise and vibration characteristics are being considered as equivalent to/or even more critical than operational performance in certain products such as office machines and home entertainment systems, which share the same space with human being's daily life. Therefore, noise reduction and sound quality improvement technology becomes an inevitable design issue for those applications. Qualitative noise characteristics of rotating polygonal disk applied to digital printer systems are presented. Overall sound pressure level change and tonal noise variation with respect to the geometrical properties of polygonal disk, operational speed, and others are briefly discussed based on experimental results.