• The Transactions of the Korea Information Processing Society
• /
• v.5 no.3
• /
• pp.592-605
• /
• 1998

주문형 비디오(VOD) 서버는 대용량의 비디오 데이터를 저장하고 사용자에게 이를 실시간으로 전송하여야 하는 제약 조건을 만족시켜야 한다. 기존의 VOD 서버 시스템은 실시간 반응 시간을 보장하기 위해 대부분 비디오 데이터의 영구 저장 장치로 하드 디스크를 사용하지만 대용량의 비디오 데이터를 저장하는 데에는 경제성과 신뢰성의 문제점이 대두된다. 본 논문은 이러한 문제점을 보완하기 위해 대용량 저장 장치인 광자기 디스크 쥬크박스를 사용하는 복합 다단계 VOD 서버에서 다양한 비디오 데이터저장 방법들을 제안하고 각 방법의 저장 비용 및 성능을 비교 분석한다. 또한, 복합 다단계 시스템과 하드 디스크를 기반으로 하는 서버의 특성을 고려하여 비디오 데이터를 저장함으로써 비용 효과적인 VOD 서버 구성 방법을 제안한다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.1
• /
• pp.1-9
• /
• 2016

Optimum cross-sectional shape of an automotive disc brake was developed based on FEM thermal analyses and the Taguchi method. Frictional heat flux and convection heat transfer coefficients were first calculated using equations and applied to the disc to calculate accurate temperature distribution and thermal deformations under realistic braking conditions. Maximum stress was generated in an area with highest temperature under pads and near the hat of ventilated disc and vanes. The SN ratio from Taguchi method and MINITAB was applied to obtain the optimum cross-sectional design of a disc brake on the basis of thermal deformations. The optimum cross-section of a disc can reduce thermal deformation by 15.2 % compared to the initial design.

• Journal of the Korean Institute of Gas
• /
• v.20 no.1
• /
• pp.40-45
• /
• 2016

Brake judder is one of the most serous problems in automotive-brake systems.it has not been eradicated despite all the efforts that many researchers and engineers have made the reduce it by studying its causes and mechanisms. Brake discs play a significant role in judder.The driver experiences judder as vibrations in the steering wheel,brake pedal and floor.in the higher freqency range.the structural vibrations are accompanied by a sound. Brake judder primarily affects the comfort but could,when confronting an inexperienced driver for the first time,lead to faulty reactions and reduced driving safety.

• Korean Journal of Optics and Photonics
• /
• v.12 no.1
• /
• pp.61-66
• /
• 2001

Defocused Fourier plane holograms are stored in disk-type holographic memories where thin recording media are used, the areal storage density per hologram and the intensity uniformity of the signal beam at the recording plane are studied. As the pixel pitch of the spatial light modulator that represents binary data increases, the storage density per hologram increases if exact Fourier holograms are stored. When defocused Fourier plane holograms are stored, however, we show that there exists an optimal pixel pitch that maximizes the area storage density per hologram in general, to increase the areal storage density per hologram, f/# of the Fourier transform lens that focuses the data image should be as small as possible. In this case, not only the intensity distribution at the recording plane but also the recording area becomes very sensitive to the degree of defocusing. Therefore, even if the exact Fourier plane holograms are stored, the defocusing effect owing to the medium thickness should be taken into account to achieve the maximal areal storage density per hologram.logram.

• Korean Journal of Optics and Photonics
• /
• v.11 no.1
• /
• pp.58-64
• /
• 2000

Assuming that the performance of holographic storage media is ideal, we estimate the area storage density of disk-type holographic memories, when the method of either angle multiplexing, or rotational multiplexing, or both are used. The area storage density is strongly dependent on the f numbers (ratio of focal length to diameter) of both the Fourier transform lens in the signal arm, denoted by $F/#_2$, and the angle range over which the reference beam is incident (or, the equivalent f number corresponding to the angle range denoted by $F/#_1$). The area storage density is largely independent of the pixel pitch of the spatial light modulator when the Fourier plane holograms are recorded, while it is sensitive to the pixel pitch when the image plane holograms are recorded. In general, to obtain high area storage density, the Fourier or at least near Fourier plane holograms rather than the image plane holograms should be recorded. In addition, when the thickness of the recording materials are less than approximately $500\mu\extrm{m}$, rotational multiplexing gives higher area storage densities than angle multiplexing does. To increase the storage density further, however, it is desirable to use both of the two multiplexing methods in combination.nation.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.11
• /
• pp.11-19
• /
• 1994

Turnaround time of a job performing frequent disk I/O operations is greatly affected by I/O bottleneck which incurs due to the large gap in the speeds of I/O devices and the CPU. This paper proposes to employ a Write Dedicated Buffer(WDB) in disk arrays to improve the response time for read requests and analyzes the scheduling policies and the efficiency of the WDB. Through a series of simulations we show that, among the three policies examined, the partial stripe join(PSJ) policy is the most effective in terms of response time for both read and write requests and that, especially when using a WDB on declustered arrays, improvement of response time for read requests becomes greater as the request rate increases.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.87-90
• /
• 2003

It has been well known that the major feature of compressible flow fields might be different depending on their formation processes. The objectives of the present study is to investigates the effect of jet development on the time history of supersonic jet flow field, accompanying nonequilibrium condensation. Especially, the behaviors of Mach disk diameter and location in a supersonic moist air jet are presented in terms of nozzle pressure ratio and initial relative humidity. The relative humidity of moist air is controlled at the nozzle supply, and the nozzle pressure ratio is varied to obtain the moderately underexpanded flows at the exit of the nozzle, installed in an indraft wind tunnel. It is found that at the same pressure ratio the Mach disk diameter increases with the initial relative humidity, while moves further upstream. Furthermore, the values of Mach disk diameter and location for increasing pressure ratio show larger than those for increasing.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.1
• /
• pp.88-95
• /
• 2004

The previous disk scheduling schemes for best-effort applications do not guarantee the real-time requirement of multimedia objects and the real-time disk scheduling schemes do not satisfy throughput of multimedia server. So, this paper propose a two-step disk scheduling scheme to satisfy the requirement of best-effort as well as soft real-time applications. This scheme is based on the round robin algorithm that imposes different weights on the best-effort task and the real-time one. The experiment results on the Linux kernel have shown that both best-effort tasks and real-time tasks could get fair service.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.5
• /
• pp.385-392
• /
• 2018

This paper suggests a new method to estimate the roll and pitch damping moment coefficients of a flying disc through sensor data from the onboard IMU module. This method can be easily performed than wind tunnel or computational fluid dynamics methods because it estimates aerodynamic coefficients simply after accumulating the inertial data through several repeated flight experiments. Estimated coefficients are applied to a simulator which is based on the flight dynamics of a flying disc. Finally, the predicted flight trajectory is compared with the true position provided by GPS, which demonstrated the validity of the proposed estimation method.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.427-430
• /
• 2007

Gas turbine disk components have been used by Ni-base superalloys which have high temperature strength for enduring stress induced by high speed rotation. This study introduced the overview of development strategy of precision forging of turbine disk and closed-die forging process for manufacturing good quality gas turbine disk. To make superior quality turbine disk, it is important to select optimal forging process conditions like preform shape, die shape and forging temperature etc. In this paper, closed-die forging process has been studied through the rigid-plastic finite element simulation. Proposed forging process can be used for the successful manufacturing of small-size gas turbine disk.