• Clean Technology
• /
• v.19 no.2
• /
• pp.156-164
• /
• 2013

In this study, we analyzed the operational characteristics of a 0.25 MW methanation pilot plant. Isothermal reactor controled the heat released from methanation reaction by saturated water in shell side. Methanation process consisting of isothermal reactor and adiabatic reactor had advantages with no recycle compressor and more less reactors compared with methanation process with only adiabatic reactors. In case that $H_2$/CO ratio of syngas was under 3, carbon deposition occurred on catalyst in tube side of isothermal reactor and the pressure of reactors increased. In case that $H_2$/CO ratio was maintained around 3, no carbon deposition on catalyst in tube side of isothermal reactor was found by monitoring the differential pressure of reactors and by measuring the differential pressure of several of tubes filled with catalyst before and after operating. It was shown that CO conversion and $CH_4$selectivity were over 99, 97%, respectively, and the maximum $CH_4$productivity was $695ml/h{\cdot}g-cat$.

• Journal of the Korean Chemical Society
• /
• v.55 no.2
• /
• pp.262-267
• /
• 2011

The denaturing high performance liquid chromatography(DHPLC) with fluorescence detector assay is very useful tool for detecting nucleic acids. Furthermore, loop-mediated isothermal amplification(LAMP) constitutes a potentially valuable tool for rapid diagnosis of pathogenic microorganisms. In this study, we evaluated the specificity, detection limit, and sensitivity of a LAMP method and DHPLC method for rapid detection of the hepatitis b virus(HBV). As a result, the LAMP assay reported here has the advantage of rapid detection whereas, DHPLC assay has more sensitivity than other assays. These findings suggest that LAMP and DHPLC assay may be good tool for rapid diagnosis of clinical HBV infection.

• Journal of the Mineralogical Society of Korea
• /
• v.22 no.4
• /
• pp.289-295
• /
• 2009

The characteristics of phosphate desorption on kaolinite was studied by batch adsorptiondesorption experiments. Desorption procedure was carried out through sequential extraction method at pH 4. The phosphorous contents were measured using UV-VIS-IR spectrophotometer with 820 nm wavelength. The adsorption-desorption reaction of P on kaolinite was irreversible, and most of adsorbed P on kaolinite were not easily dissolved to aqueous solution, but may might be fixed on kaolinite surface. The desorption isotherms were well fitted with the Freundlich and Temkin equations in the case of short reaction and long reaction time, respectively. The desorption reaction was divided into the early fast reaction and the later slow reaction. The percentage of desorption generally decreased with increasing adsorbed P concentration and increasing desorption reaction time.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.7
• /
• pp.1193-1203
• /
• 2000

In this study, in order to remove Cd(II) from aqueous solutions, strongly acidic cation exchange resin(SK1B) by Diaion Co. was employed as an adsorbent. Experiments were mainly performed in two parts at room temperature($25{\pm}5^{\circ}C$) : batch tests and adsorption kinetics tests. In batch tests adsorption equilibrium time, pH effects, temperature effects, several adsorption isotherms, and finally desorption tests were examined. In differential bed tests, an optimum flow rate and an overall adsorption rate were obtained. In the batch experiment, adsorption capability increased with pH and became constant above pH 6 and adsorption quantity increased with temperature. Batch experimental data found that Freundlich and Sips adsorption isotherms were more favorable than Langmuir adsorption isotherm over the range of concentration (5~15ppm). The desorbent used in the desorption test was hydrochloric acid solution with different concentrations(0.01~2N). The degree of regeneration increased with concentration of desorbent and decreased slightly with the number of regeneration. In the continuous flow process using a differential bed reactor, the optimum flow rate was $564m{\ell}/min$ above which the film diffusion resistance was minimized. The overall adsorption rate for the removal of Cd(II) by cation exchange resin was found as follows ; $r=1.3785C_{fc}^{1.2421}-2.0907{\times}10^{0.0746C_i}\;q_e^{0.0121C_i-0.0301}$

• Applied Chemistry for Engineering
• /
• v.18 no.5
• /
• pp.511-515
• /
• 2007

The yield of oil was rapidly increased at $440^{\circ}C$ compared to $400^{\circ}C$ and $420^{\circ}C$ when the isothermal pyrolysis of waste ship lubricating oil was carried out in tubular type reactor, and pyrolysis was almost finished within 30 min. The yield of gas was decreased depending on the reaction temperature in which that of solid was not much changed. Pyrolysis experiments of waste ship lubricating oil were carried out with used ZSM-5 produced from a petrochemical process. The yield of gas was highly increased in the case of used ZSM-5 and fresh ZSM-5 compared to the case without catalyst. The produced oil and gas were almost constant for fresh ZSM-5 and used ZSM-5 at the same reaction temperature. In the reaction temperature $400{\sim}440^{\circ}C$, the selectivity of $C_5-C_{11}$ was two times higher with fresh ZSM-5 and used ZSM-5 than the case without catalyst.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2004.04a
• /
• pp.135-138
• /
• 2004

본 연구는 중금속으로 오염된 폐수처리에 있어 친환경적 유기흡착제로서 휴믹물질의 활용성을 평가하기 위한 기초 연구로서 이탄(peat moss)으로부터 Humin을 분리 한 후, 중금속 이온(Cd(II),Cu(II))과의 흡착특성을 조사하였다. 이탄으로부터 추출한 peat-Humin의 함량은 94%이상을 나타냈으며, 분자의 작용기 특성은 일반 토양 휴믹물질(soil humic substance)과 유사하였다. peat-Humin과 중금속 이온(Cd(II),Cu(II))과의 흡착 반응은 5분내에 빠른 흡착형을 보였으며, pH 5-6에서 가장 높은 중금속 제거율을 보였다. pH 3의 산성조건에서도 50%정도의 제거율을 보였다. pH 5에서의 등온흡착 실험결과를 Freundlich 등온식에 적용하여 해석한 결과, 각의 중금속에 대한 peat-Humin의 흡착상수(Kf)는 Cd(II)이 8.07 그리고 Cu(II)가 4.56으로 나타났다.

• Korean Chemical Engineering Research
• /
• v.57 no.3
• /
• pp.420-424
• /
• 2019

In SNG (synthetic natural gas) process by proposed RIST(Research Institute of Industrial Science & Technology)-IAE(Institute for Advanced Engineering) (including three adiabatic reactors and one isothermal reactor), the methanation reaction and water gas shift (WGS) reaction take place simultaneously, and the supply of steam with syngas might control the temperature in catalyst bed and deactivate the catalyst. In this study for development of SNG process, the characteristics of the methanation reaction with a Ni-based catalyst by prepared RIST and using a low $H_2/CO$ mole ratio (including $CO_2$ 22%) are evaluated. The operating conditions ($H_2O/CO$ ratio of the $1^{st}$ adiabatic reactor, operating temperature range of $4^{th}$ isothermal reactor, etc.) were reflected the results from previous studies and in the same condition a pilot scale SNG process is carried out. As a results, the pilot scale SNG process is stable and the CO conversion and $CH_4$ selectivity are 100% and 96.9%, respectively, while the maximum $CH_4$ productivity is $660ml/g_{cat}{\cdot}h$.

• Polymer(Korea)
• /
• v.37 no.2
• /
• pp.240-248
• /
• 2013

The curing behaviors of diglycidyl ether of bisphenol A (DGEBA) with mercaptan hardener were studied by the comparison with amine-adduct type hardener. Curing behaviors were evaluated by DSC at dynamic and isothermal conditions. In the DSC, the dynamic experiments were based on the method of Kissinger's equation, and the isothermal experiments were fitted to the Kamal's kinetic model. Activation energy of epoxy/amine-adduct type hardener was ca. 40 kcal/mol. As the functional group of mercaptan hardener, -SH increased, on epoxy/mercaptan hardeners, the activation energies decreased from 28 to 19 kcal/mol. Epoxy/amine-adduct type hardener was initiated at $90^{\circ}C$ or higher. However, epoxy/mercaptan hardeners reduced the initiation temperatures below $80^{\circ}C$ and shortened the durations of curing reaction within 10 min. We found out that the reaction kinetics of epoxy with mercaptan hardener followed the autocatalytic reaction models, and the maximum reaction rates were shown at the conversions of 20~40%.

• Korean Chemical Engineering Research
• /
• v.51 no.6
• /
• pp.692-699
• /
• 2013

In this study, isothermal (350, 375, 400, 425, 450, 500, $850^{\circ}C$) experiments were carried out using a custom-made thermobalance to analyze the thermal decomposition properties of refuse plastic fuel (RPF), which is to be used as a cofiring fuel with a sub-bituminous coal at commercial circulating fluidized bed (CFB) boiler in Korea. In isothermal pyrolysis results, no change in the reaction model was observed in the temperature range of $375{\sim}450^{\circ}C$ and it was revealed that the first order chemical reaction (F1) is the most suitable among 12 reaction models. The activation energy shows similar results irrespective of application of reaction model in that the activation energy was 39.44 kcal/mol and 36.96 kcal/mol when using Arrhenius equation and iso-conversional method ($0.5{\leq}X{\leq}0.9$) respectively. Mean-while, the devolatilization time ($t_{dev}$) according to particle size (d) of RPF could be expressed as $t_{dev}=10.38d^{2.88}$ at $850^{\circ}C$, operation temperature of CFB and for even distribution and oxidation of RPF in CFB boiler, we found that the relationship of average dispersion distance (x) and particle size was $x{\leq}1.58d^{1.44}$.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.4
• /
• pp.451-461
• /
• 2022

CFD analysis including optimization process was conducted to design shell and tube CO₂ methanation reactor cooling system. The high-pressure saturated water flowed into the cooling system and was evaporated by heat flux from reacting tubes. The optimization process decided the gap between tubes and reactor diameter to satisfy objective functions related to temperature. The results showed that the gap and diameter reduced about 30% and 3.6% respectively. Averaged surface temperature satisfied the target value and the min-max deviation was minimized.