• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.6
• /
• pp.1021-1029
• /
• 1992

A rational and straightforward method is introduced for developing continuum models of large platelike periodic lattice structures based on energy equivalence. The procedure for developing continuum plate models involves the use of existing well-defined finite element matrices for the easy calculation of strain and kinetic energies of a repeating cell, from which the reduced stiffness and mass matrices are obtained in terms of continuum degrees- of-freedom defined in this paper. The equivalent continuum plate properties are obtained from the direct comparison of the reduced matrices for continuum plate with those for lattice plate. The advantages of the present continuum method are that it may be applied to arbitrary lattice configurations and may give most diverse equivalent continuum plate properties including all kinds of coupling, while other methods may give only limited structural properties. To evaluate the continuum method developed in this paper, free vibration analyses for both of continuum and lattice plates are conducted. Numerical results show that the present continuum method gives very reliable structural and dynamic properties compared to other well-recognized methods.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.1
• /
• pp.29-38
• /
• 1994

Linear composite theory as well as a finite element program is developed for axisymmetric elastomeric bearings. This study is limited to axisymmetrically loaded horizontal layered systems with linear, elastic, small' deformation conditions. A multiscale method is used in the development of the composite theory which enables us to model inhomogeneous layered composites as equivalent homogeneous, orthotropic material. Only continuity of the prime variables is required for the finite element analysis, allowing the use of simple $C_o$ elements whereas rather complicated theories presented in the past need more requirements. Four node isoparametric elements are used in the study. The developed theory of this paper is limited to linear conditions, however, the analysis can be extended to nonlinear behavior of flexible material in elastomeric bearing by using multiscale method presented here. Two numerical examples are examined and compared to the results of discrete and previously obtained composite analysis to verify the theory.

• Tunnel and Underground Space
• /
• v.14 no.6 s.53
• /
• pp.423-428
• /
• 2004

The stability of tunnels is usually analyzed as plain strain condition and rock bolts are assumed as 2 dimensional equivalent continuum structures. In this study, 2 and 3 dimensional numerical analyses were conducted to verify the validity of 2 dimensional analysis of rock bolts. Since the results of 2 dimensional analysis showed more than $10\%$ differences in poor rocks, it seems that 3 dimensional analysis is required in poor rocks.

• Journal of the Korean GEO-environmental Society
• /
• v.4 no.2
• /
• pp.77-91
• /
• 2003

The Hoek-Brown failure criterion for rock masses developed first in 1980 is widely accepted and has been applied in a variety of rock engineering problems including slope analyses. The failure criterion was modified over the years because rock mass strength by the original failure criterion in 1980 was overestimated. The modified failure criterion, named Generalized Hoek-Brown Failure Criterion, was proposed with a new classification called the Geological Strength Index(GSI) in 1994. Generally, Hoek-Brown failure criterion is applied in numerical analyses of rock mass behaviors using equivalent Mohr-Coulomb parameters estimated by linear regression method. But these parameters estimated by this method have some inaccuracies to be applied and to be incorporated into numerical models and limit equilibrium programs. The most important issue is that this method cannot take account of non-linear characteristics of Hoek-Brown criterion, therefore, equivalent Mohr-Coulomb parameters is used as constant values regardless of field stress distribution in rock masses. In this study, the numerical analysis on rock slope stability considering non-linear characteristics of Hoek-Brown failure criterion was carried out. Futhermore, by the latest Hoek-Brown failure criterion in 2002, the revised estimating method of equivalent Mohr-Coulomb parameters was applied and rock mass damage criterion is introduced to account for the strength reduction due to stress relaxation and blast damge in slope stability.

• Journal of the Korean Magnetics Society
• /
• v.20 no.3
• /
• pp.100-105
• /
• 2010

For predicting magnetic signals due to the remanent magnetization distributed on a ferromagnetic ship hull, this paper presents an efficient methodology for solving inverse problems, where the material sensitivity analysis based on the continuum mechanics is combined with the equivalent magnetic models. To achieve this, the 3D magnetic charge model and the magnetic dipole moment model are introduced and material sensitivity formulae applicable to each equivalent model are derived. The formulae offer the first-order gradient information of an objective function with respect to the variation of the magnetic charge or magnetic dipole and so an optimal solution can be easily obtained regardless of the number of design variables. To validate the proposed method, the numerical results are comparison with the real measurements of a mock-up model.

• Journal of the Korean GEO-environmental Society
• /
• v.20 no.5
• /
• pp.13-21
• /
• 2019

There are many cuts or natural rock slopes that remain stable for a long time in the natural environment with steep slopes ($65^{\circ}$ to $85^{\circ}$). In terms of design practice, the rock mass consisting of similar rock condition and geological structures is defined as a good continuum rock slope, and during the process of decision making angle of this rock slope, it will be important to establish the geotechnical properties estimating method of the continuum rock on the process of stability analysis in the early stages of design and construction. In this study, the stability analysis of a good continuum rock slope that can be designed as a steep slope proposed a practical method of estimating the shear strength by induced from the Hoek-Brown failure criterion, and in addition, the design applicability was evaluated through the stability analysis of steep rock slope. The existing method of estimating the shear strength was inadequate for practical use in the design, as the equivalent M-C shear strength corresponding to the H-B envelope changes sensitively, even with small variations in confining stress. To compensate for this problem, it was proposed to estimate equivalent M-C shear strength by iso-angle division method. To verify the design applicability of the iso-angle division method, the results of the safety factor and the displacement according to the change in angle of the cut slope constructed at the existing working design site were reviewed. The safety factor is FS=16~59 on the 1:0.5 slope, FS=12~52 on the 1:0.3 slope, most of which show a 10~12 percent reduction. Displacement is 0.126 to 0.975 mm on the 1:0.5 slope, 0.152 to 1.158 mm on the 1:0.3 slope, and represents an increase of 10 to 15%. This is a slightly change in normal proportion and is in good condition in terms of stability. In terms practical the working design, it was confirmed that applying the shear strength estimated by Iso-angle division method derived from the H-B failure criterion as a universal shear strength for a good continuum rock mass slope was also able to produce stable and economic results. The procedure for stability analysis using LEM (Limit Equilibrium Analysis Method) and FEM (Finite Element Analysis Method) will also be practical in the rock slope where is not distributed fault. The study was conducted by selecting the slope of study area as a good rock condition, establishing a verification for which it can be applied universal to a various rock conditions will be a research subject later on.

• Computational Structural Engineering
• /
• v.10 no.4
• /
• pp.131-142
• /
• 1997

In this paper the kinematics of damage for finite elastoplastic deformations is introduced using the fourth-order damage effect tensor through the concept of the effective stress within the framework of continuum damage mechanics. Unlike the approach of strain equivalence or energy equivalence, which is applicable only to small strains, the proposed kinematic description provides a relation between the effective strain and the damage elastoplastic strain in finite deformation. This is accomplished by directly considering the kinematics of the deformation field both real configuration. The proposed approach shows that it is equivalent to the hypothesis of energy equivalence at finite strains. The damage effect tensor in this work is explicitly characterized in terms of a kinematic measure of damage in the elastoplastic domain through a second-order damage tensor.

• Computational Structural Engineering
• /
• v.9 no.1
• /
• pp.65-76
• /
• 1996

The initiation and growth of microcracks or microvoids inside concrete results in the progressive degradation of concrete. This damage processing along processing along with plastic deformation is main cause of nonlinear behavior of concrete. In this study, a continuum damage model of concrete is developed for the analysis of the nonlinear behavior of concrete due to damage and elasto-plastic deformation. Anisotropic damage tensor is used to describe the anisotropy of concrete and hypothesis of equivalent elastic energy is used to define the effective elastic tensor. The damage model including the damage evolution law and constitutive equation is derived with damage variable and damage surface which is defined by damage energy release rate by using the Helmholtz free energy and dissipation potential based on the thermodynamic principles. By adopting a typical plasticity model of concrete, plasticity of concrete is included to this model. Afinite element analysis program implemented with this model was developed and finite element analysis was performed for the analyses of concrete subjected to uniaxial and biaxial loadings. Comparison of the results of analysis with those of experiments and other models shows that the model successfully predicts the nonlinear behavior of concrete.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.3
• /
• pp.223-233
• /
• 2011

A ceramic monolithic catalyst is a honeycomb structure that consists of two layers. The honeycomb structure is regarded as a continuum in structure and heat-flow analysis. The equivalent mechanical properties of the honeycomb structure were determined by performing finite element analysis (FEA) for a test specimen. Bending strength experiments and FEA of the test specimen used in ASTM C1674-08 standard test were performed individually. The bonding coefficient between the cordierite ceramic layer and the washcoat layer was almost zero. The FEA test specimen was modeled on the basis of the bonding coefficient. The elastic modulus, Poisson's ratio, and the thermal properties of the ceramic monolithic substrate were determined by performing the FEA of the test specimen.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.8 no.2
• /
• pp.155-166
• /
• 1988

An "equivalent homogeneous, orthotropic" model that includes edge effects and an accompanying finite element analysis is presented for elastomeric bearings. The model is developed for two-dimensional configurations with horizontal layers, and for linear, elastic, small deformation conditions. The equivalent homogeneous theory, in addition to capturing the overall response characteristics of the layered elastomeric bearing system, approximately models the important edge effects, which occur at and near boundaries that cut the layers, and the stress concentrations at layer interfaces. The primary dependent variables for the theory have been selected such that the highest derivatives appearing in the strain energy function are first-order, thus requiring only $C_0$ continuity of the finite element approximations. As a result, the finite element analysis is simple and computationally efficient. Numerical examples are presented to verify the theory and to illustrate potential applications of the analysis.