• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.7
• /
• pp.4835-4841
• /
• 2015

The effect of particle size and compaction pressure on the thermoelectric properties of n-type $FeSi_2$ was investigated. The starting powders with various particle size were pressed into a compact (compaction pressure; $70{\sim}220kg/cm^2$). The compact specimens were sintered at 1473 K for 7 h and annealed at 1103 K for 100 h under Ar atmosphere to transform to the semiconducting ${\beta}$-phase. The microstructure and phases of the specimens were observed by SEM, XRD and EDS. The electrical conductivity and Seebeck coefficient were measured simultaneously for the same specimen at r.t.~1023 K in Ar atmosphere. The electrical conductivity increased with decreasing particle size and hence the increases of relative density of the sintered body and the amount of residual metallic phase ${\varepsilon}$-FeSi due to a increase of the electrical conductivity. The Seebeck coefficient exhibited the maximum value at about 700~800 K and decreased with decreasing particle size. This must be due to a increase of residual metallic phase ${\varepsilon}$-FeSi. On the other hand, the change of compaction pressure appeared to have little effect on the thermoelectric properties. Consequently, the power factor would be affected more by particle size than compaction pressure.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.18 no.4
• /
• pp.607-614
• /
• 1996

Nasal bone fracture is common in mid-facial trauma patients. In these patients, facial bone and nasal bone fracture are reducted at same time, but definite nasal reduction is difficulty in these patients because of nasotracheal intubation during general anesthesia and facial swelling in early facial trauma patients. If nasal packing and MMF are needed, there are difficult to maintain the reducted nasal bone because of some difficulty in airway maintenance after nasal packing and increasing the patient discomfort. So postoperative nasal deformity is more common in these combined patients. Secondary rhinoplasty is necessary in these patients who have deformed nasal bone, and there are many methods and materials for secondary rhinoplasty. But if primary nasal bone was reducted symmetrically, it is easy in secondary rhinoplasty. We present 7 cases of secondary rhinoplasty in mid-facial trauma patients who had combined nasal bone fracture. In these patients, primary nasal bone reduction carried with closed reduction method during primary facial bone reduction. About 6 months later, we performed secondary rhinoplasty with iliac bone and alloplastic materials. So we report these cases with literatures.

• Food Engineering Progress
• /
• v.13 no.3
• /
• pp.169-175
• /
• 2009

Water soluble polysaccharides (WSP) and arabinogalactan of Portulaca oleracea L. (POL) were increased after extrusion and commercial cellulase treatment. Arabinose and galactose content increased more about 1.5 times than those of raw POL, and rhamnose also increased about 2.6 times in WSP. High molecular weight fraction (I) of POL depending on extrusion condition including Ext I, Ext II and Ext III degraded into low molecular weight fraction (II) about 37, 29, and 26%, respectively, ranged from 67,000-69,000 Da of molecular weight. Especially, the molecular weight and composition of WSP with extruded, were increased from 9 to 13% in low molecular weight fraction, compared to those of raw POL. Solubilization and degradation of polysaccharides were a directly propotional to specific mechanical energy in POL extrusion. WSP obtained by extrusion at Ext I and Ext II were found to be effective antioxidants in different in vitro assays with regards to 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical scavenging activity and Trolox equivalent antioxidant capacity (TEAC). However, these results suggest that WSP obtained using extrusion and subsequent enzymatic treatment may be an effective method to produce arabinogalactan from POL and be used as a functional food ingredients.

• Journal of the Korea Concrete Institute
• /
• v.13 no.4
• /
• pp.406-413
• /
• 2001

Up to this day, reinforced spun concrete pipes have been widely used as drain pipes. However, many reinforced spun concrete pipes are exposed to the deteriorated environment such as freezing-thawing damage and chemical attack by the growth of a sulfur-oxidizing bacterium isolated from corroded concrete. The purpose of this study is to evaluate the effects of lining by polymer-modified mortar using polymer dispersions as cement modifier on the development in durability of reinforced spun concrete pipe. The polymer-modified mortars were prepared with various polymer types and polymer-cement ratios, and tested for compressive and flexural strengths, acid, freezing-thawing, and heat resistances. And then, the reinforced spun concrete pipe product lined by polymer-modified mortars was tested for adhesion in tension and surface conditions according to curing temperatures in the field. From the test results, it is apparent that the polymer-modified mortars have good mechanical properties and durability as a lining material. In practice, all polymers can be used as lining the materials for reinforced spun concrete pipe, and types of polymer, and polymer-cement ratio and curing conditions are controlled for a good lining product.

• Journal of Chest Surgery
• /
• v.34 no.9
• /
• pp.692-697
• /
• 2001

Background: The left main coronary artery surgical angioplasty has become the choice of surgical procedure in isolated LM disease. We have performed 22 cases of LMCA surgical angioplasy since 1996. We report the immediate and long term result of the surgical angioplasty with their postoperative angiography. Material and Method: Between July 1994 and October 2000, 22 patients(11 men and 11 women) were subjected to surgical patch angioplasty of the LMCA, 1 patient had an additional angioplasty performed on the proximal right coronary artery. The LMCA was approached anteriorly with or without transection of the main pulmonary artery(21 cases), and in a patient who had undergone an aortic valve replacement, LMCA was approached superiorly with transection of the ascending aorta. Additional grafting was required in 5 cases. The on-lay patch was used with autologous pericardium in 6 cases and bovine pericardium in 16 cases. Result: There was no operative mortality. There was 30~50% stenosis of the anastomosis site in 3 cases at the postop. coronary angiography. Coronary angiography was reperformed in 5 cases between 5th months and 15th months postoperatively. There was 40~60% stenosis of the anastomosis site in 2 cases. There was one death at 42nd months postoperatively but the cause was unknown. No patient complained of angina with a mean follow up of 48.$\pm$22.5 months. Conclusion: There were only several coronary angiographic results in long term follow-up but we had relatively good clinical results for LMCA surgical angioplasty in the immediate and long term. The excellence of LMCA surgical angioplasty needs the result of the long term follow-up.

• Elastomers and Composites
• /
• v.43 no.4
• /
• pp.253-258
• /
• 2008

In this study polyamide 6,6 based thermoplastic composite with graphite and carbon black had been examined feasibility for separators of fuel cell which requires good mechanical and electrical properties with gas impermeability. The effects of molding pressure and filler content on the properties of the composite were investigated. Maximum flexural modulus was obtained about 80 wt% graphite, while electrical conductivity increased with graphite content. Flexural strength increased with molding pressure and tended to level-off from $400\;kgf/cm^2$. Molding pressure did not affect the electrical conductivity. The addition of carbon black enhanced the electrical conductivity of the composite. Mechanical properties were decreased under acidic condition.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.43.2-43.2
• /
• 2009

Al-Mg 알루미늄 합금은 강도가 높고 성형성이 우수하여 수송기기 경량화용 소재로서 사용량이 증가하고 있다. 특히고강도 특성을 보이는 Al-Mg-Mn합금은 자동차, 선박및 철도차량등의 형재 및 판재로 그 사용량이 증가하고 있다. 또한 결정립을 미세화 시킨 Al-Mg-Mn합금판재의 경우에는 온간성형으로 복잡한 형상의 판재부품제조에 사용되고 있다. 연속주조공정인 Twin roll strip casting(TRC)은용탕으로부터 직접 판재를 생산할 수 있는 공정으로 주로 순알루미늄계열의 판재 생산에 사용되고 있으나 최근에는 고강도 판재의 저비용 생산을 위하여 고합금계 판재에 적용하는 연구가 수행되고 있다. 합금량이 높은 고강도Al-Mg계 합금의 TRC 주조시 고액공존구간이 커서 더욱 정밀한 공정제어가 필요하다. 또한 기존의 슬라브주조방식보다 높은 냉각속도로 주조가 가능하기 때문에 결정립 및 정출상의 미세화공정으로 응용되기도한다. 본 연구에서는 TRC공정을 기초로 주조시 열간 압연의효과를 동시에 부여하는 용탕직접압연공정을 개발하였으며 상용 고강도 알루미늄 합금인 5083합금 판재를제조하였다. 또한 기존 Al-Mg 합금에 Mn을 첨가하여 용탕직접압연함으로서 정출상의 크기 및 밀도를 제어하여 강도가 우수한 Al-Mg-Mn 합금판재를 제조하는 기술을 개발하였다. 용탕직접압연된 Al-Mg-Mn계 합금의 경우에 주조시 높은 냉각속도로 인하여 결정립이 미세하고 Al6Mn과 같은 미세한 정출상이 다량 형성되었으며, 최종압연 및 열처리에 의하여 높은 강도를 갖는 고강도 알루미늄 합금 판재의 제조가 가능하였다.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.244-249
• /
• 2001

In this paper, we present the simultaneous measurement of the fabricaition strain and temperature during and after cure of unsymmetric composite laminate uising fiber optic sensors. Fiber Bragg grating/extrinsic Fabry-Perot interferometric (FBG/EFPl) hybrid sensors are used to measure those measurands. The characteristic matrix of sensor is analytically derived and measurements can be done without sensor calibration. A wavelength-swept fiber laser is utilized as a light source. FBG/EFPI sensors are embedded in a graphite/epoxy unsymmetric cross-ply composite laminate at different direction and different location. We perform the real time measurement of fabrication strains and temperatures at two points of the composite laminate during cure process in an autoclave. Also, the thermal strains and temperatures of the fabricated laminate are measured in thermal chamber. Through these experiments, we can provide a basis for the efficient smart processing of composite and know the thermal behavior of unsymmetric cross-ply composite laminate.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.174-174
• /
• 2013

현재 자동차 강판 시장에서는 승객들의 안전 확보와 연비 향상을 위하여 자동차 강판의 경량화 및 고장력화가 급속히 진행되고 있다. 더불어 소비자는 더욱 아름답고 멋있는 외관을 추구하면서 정교한 디자인이 가능할 수 있도록 높은 성형성을 갖는 강판에 대한 요구도 또한 증대되고 있다. 따라서 강도와 성형성을 동시에 확보할 수 있는 DP형, TRIP형 등의 다양한 컨셉을 갖는 변태강화형 고장력강에 대한 개발 요구가 점점 심화되고 있으나 이들 고장력강의 상 제어를 위하여 첨가된 Si, Mn등의 성분들이 표면에 안정한 산화물을 형성하기 때문에 이러한 고장력강은 표면 품질이 열위한 것으로 보고 되고 있다. 따라서 기존 연구에서는 열처리중 표면으로 확산되어 올라오는 Si, Mn 산화물의 저감을 위하여 분위기 중 산소농도나 노점등을 조절하거나, 산화전처리, 선도금처리 등을 통하여 Si, Mn 의 표면 선택산화를 제어하여 도금 결함을 최소화하려는 연구가 많이 진행되고 있다. 그러나 이러한 연구들은 대부분 강판 표면에서의 산화/환원의 반응에 대한 분위기 요인을 제어하는 연구들이며 실제 Si, Mn등의 산화성 원소들이 어떠한 조건에서 어떠한 경로들을 통해서 이동하여 표면으로 올라오는지에 대한 연구는 부족한 상황이다. 따라서 본 연구에서는 산화성 원소들의 표면 확산 거동에 대한 고찰을 위하여 다양한 열처리 온도 조건을 통한 표면 도금성 경향, 합급화 경향 및 표면 분석결과를 바탕으로 확산 거동에 대한 경향을 밝히고자 하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.184-184
• /
• 2008

저온 동시 소성 세라믹(LTCC, Low Temperature Co-firing) 기술 중에서 테이프 캐스팅(tape casting)은 얇고 균일한 세라믹 그린 쉬트를 연속 성형할 수 있으며 성형된 쉬트의 밀도, 표면상태, 두께제어 등이 매우 중요하다. 얇고 균일한 세라믹 그린 쉬트를 제작하기 위해서 슬러리의 분산성과 레오로지 특성은 매우 중요한 요소이며 첨가되는 유기물 첨가제들의 종류와 함량비는 슬러리의 분산성과 점도에 큰 영향을 미친다. 본 연구에서는 유기물 첨가제의 종류와 함량에 따른 슬러리의 점도와 그린 쉬트의 밀도 및 두께 제어에 미치는 영향을 고찰하였다. 바인더로는 acryl, polyvinyl 계를 사용하였으며, 가소제는 glycol, phatalate 계를 사용하였다. 각각 2 종류의 바인더와 가소제의 함량에 따른 레올로지 거동과 그런 쉬트의 밀도를 측정하였다. 각 조성별로 준비된 슬러리를 사용하여 테이프 캐스팅 방법으로 제작된 그린 쉬트의 두께를 측정하여 유기물 첨가제 조성이 그린 쉬트의 두께제어에 미치는 영향을 평가하였다.