• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.376-377
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.125-126
• /
• 2013

• Tribology and Lubricants
• /
• v.16 no.1
• /
• pp.1-8
• /
• 2000

Friction and wear tests have been performed on nylon, acetal resin, and PTFE (polytetrafluoroethylene), in reciprocating dry sliding conditions against steel discs. According to the results, acetal resin showed the lowest wear rates and PTFE exhibited the lowest friction coefficient. The prominent wear mechanisms found were adhesion and abrasion.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2004.10a
• /
• pp.231-232
• /
• 2004

• Proceedings of the KWS Conference
• /
• 1994.05a
• /
• pp.211-214
• /
• 1994

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.158-158
• /
• 2011

천수방정식과 같은 쌍곡선형 미분방정식의 불연속 해에 대한 Riemann 해법은, 1950년대 말 공기동역학 분야에서 S. K. Godunov의 선구적인 시도 이후, 다양한 영역에서 성공적으로 적용되고 있다. 당초 제안된 해법은 공간에 대해 1차 정도였으나, 2차의 정도를 얻을 수 있는 기법이 1970년대 말 B. van Leer에 의해 제안되었으며, MUSCL로 불린다. 서로 인접한 격자의 보존변수가 고려된 경사가 도입되어 두 격자에 의해 공유되는 변의 좌 우에서 선형으로 보존변수가 재구축되는 MUSCL은 제한자와 함께 이용될 때, 구조 격자 체계에서 비교적 단순하면서도 효과적인 적용성이 입증되었다. 그런데, 이 기법을 2차원의 비구조 격자 체계에 적용하는 경우, 인접한 모든 격자의 보존변수를 고려한 평면의 경사를 결정해야 하는 어려움이 따른다. 특히, 삼각형 비구조 격자에 적용할 경우 최적의 평면을 결정하기 위해 Green-Gauss 적분식이나 최소-자승법 등을 이용하게 된다. 이에 비해, 2010년 T. Buffard와 S. Clain이 제안한 다중경사 기법은 격자의 각 변에서 경사가 각각 결정되는 방법으로 계산량이 많은 Green-Gauss 적분식이나 최소자승법을 피할 수 있는 장점이 있는 것으로 알려져 있다. 정확해가 알려진 두 경우에 대해 몇 가지 제한자를 적용한 결과를 1차 정도의 해와 함께 비교하였으며, superbee 제한자에 의한 결과가 우수하였으나, 희유파와 충격파가 맞닿는 곳에서 수치 분산이 나타났다. minmod 제한자의 결과가 대체로 무난하였으며, 이를 2차원 댐 붕괴 문제에 적용하여 1차 정도의 해와 비교하였다. 마찰이 없고 초기 수심이 댐 상류에서 10 m, 하류에서 5 m로서 물이 차 있는 경우, 1차 정도의 해에서 나타나는 수치 소산이 2차 정도에서는 발생되지 않았다. 댐 하류에서 초기에 수심이 영으로 바닥이 드러난 경우에서 마찰의 영향을 검토하였다. 마찰이 있는 경우, 마찰 경사 항의 Manning 계수를 0.04로 두었으며, 마찰에 의한 영향이 잘 드러났다. 수심이 50 mm 보다 작은 경우에는 마찰을 적용하지 않았다. 이 연구는 환경부 '차세대 핵심환경기술개발 사업'의 지원에 의한 것이다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.15 no.2
• /
• pp.61-69
• /
• 2011

In this paper, the factors affecting the dynamic characteristics of a polyurethane spring restoring disk bearing are analysed to predict the dynamic behavior of the bearing. The prediction results and the test results are compared. The Young's modulus of the polyurethane spring, which varies according to strain of spring and the friction coefficient, of PTFE (PolyTetraFluoroEthylene), which varies according to the velocity and pressure of PTFE, are considered as the factors influencing the dynamic characteristics. W-PTFE virgin products are used and polyurethane springs are produced for the tests. The equation related to changing the friction coefficient and the modulus of elasticity are obtained through an inverse estimation of the test results. The estimation results, considering the factors affecting the dynamic characteristics, simulate the test results more appropriately than the estimation without the consideration of those factors.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.12 no.1
• /
• pp.57-66
• /
• 2008

An experimental study was performed to evaluate seismic reduction performance and applicability of 3-dimensional floor isolation system to the main control room of nuclear power plant. A friction pendulum system(FPS) and air spring were designed and fabricated for 3-dimensional floor isolation system. Two kind of the partial experimental model of a main control room attached to the FPS and air spring were tested on the shaking table. The experimental model consisted of a control panel, a $2.5m{\times}2.5m$ access floor, four FPS and air springs. The artificial time histories based on the vertical and horizontal floor response spectrums(OBE, SSE) of the main control room were used as the earthquake input signals in the test. Compared to non-isolated system, the seismic response of experimental models using 3-dimensional floor isolation system were shown considerable seismic reduction performance.

• Journal of Welding and Joining
• /
• v.17 no.5
• /
• pp.69-76
• /
• 1999

A copper-tungsten sintered alloy(Cu-W) has been friction welded to a tough pitch copper in order to investigate the effect of upset pressure on friction weldability. Under the condition of friction time 0.8sec, upset pressure 150MPa, the tensile strength and Charpy impact value of the friction welded joint were 336MPa, $400KJ/m^2$ respectively. And highest temperature of the weld measured was below $800^{circ}K$ which is very lower than melting point of Cu($1356^{circ}K$). Under the same conditions, W grains picked up in Cu matrix from Cu-W profitably affected on these mechanical fracture, and were dispersed in Cu by plastic flow during brake time.

• Journal of the Korean Ceramic Society
• /
• v.39 no.1
• /
• pp.79-85
• /
• 2002

Plasma-sprayed Cr$_2$O$_3$-based coatings containing MoO$_3$were studied to gain a better understanding of the influence of MoO$_3$composition in the coatings on their tribological behaviour. A reciprocal type tribo-tester was employed to examine friction and wear behavior of the specimens at room temperature. The physical characteristics of worn surfaces were investigated by scanning electron microscopy and chemical composition of the coating surfaces was analyzed using a X-ray photoelectron spectrometer. The results showed that friction coefficient of the MoO$_3$-added coatings were lower than those without MoO$_3$addition. However pure Cr$_2$O$_3$coating showed the lowest wear loss at the self-mated test. The larger protecting layers were observed at the worn surface of plasma spray coated specimens with MoO$_3$addition. XPS analysis of the protecting layer indicated that MoO$_3$composition was dominantly formed at the surface. MoO$_3$composition in the protecting layer appears to be more favorable in reducing the friction.