• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2033-2035
• /
• 2001

본 연구는 기존의 자전거에 전기 구동장치를 장착시켜서 자전거의 페달링에 의하여 검출된 답력을 이용한 보조 동력 구동장치에 대한 개발이다. 답력의 검출은 불시의치차를 이용한 동력 전달장치를 이용하였다. 이 장치의 입력기어에서 출력기어로 동력을 전달하는 아이들 피니언 기어와 결합된 캐리어를 동력 전달시 발생하는 반력에 의한 각도를 이용하여 토크량을 측정하였다. 동력전달을 할 경우 발생하는 반력에 의한 회전각을 자기센서를 이용하여 답력을 측정하였다. 이 답력을 구동회로에 인가하여 보조동력을 자전거에 인가함에 따라 주행을 쾌적하게 하도록 개발하였으며 실험을 통하여 실용성을 고찰하였다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.1
• /
• pp.78-83
• /
• 2001

To establish the optimized capacity of power transformer, this paper proposed the total demand factor of power supply facility. For this purpose, it was measured and analysed the operating pattern of power supply acility Installed in the apartment. As a result, it is found that the demand factor of each facility is following that : i) In case of [Xlwer water suwly facility ; 47[%], ii) In case of waste water facility ; 44[%]. Also, it was analysed that the optimized total demand factor of power load is proper 42[%1 than 52[%] to lead the efficiency operation.ration.

• Proceeding of EDISON Challenge
• /
• 2013.04a
• /
• pp.331-336
• /
• 2013

본 연구에서는 인간동력 항공기의 주익에 적용할 에어포일 형상에 대한 공력 특성을 파악하였다. 인간동력 항공기 날개에 적용하기에 적절한 에어포일을 조사하였으며, DAE11, DAE21, DAE31, SG6043 익형에 대하여 전산유체해석 프로그램인 EDISON_CFD를 통하여 비교하였다. 인간동력 항공기의 낮은 비행속도를 감안하여 $6{\times}10^5$의 저 레이놀즈수에서 받음각에 따른 양력계수, 항력계수, 양항비 등을 얻어내어 상호 비교 분석하였다. 본 연구를 통해 인간동력 항공기 주익에 적용할 저 레이놀즈 에어포일 형상을 최종적으로 선택할 수 있는 근거 자료를 확보하였다.

• Journal of ILASS-Korea
• /
• v.27 no.4
• /
• pp.203-210
• /
• 2022

Combustion and performance of a spark-ignition engine fueled with propane and butane were analyzed under different compression ratio. The electricity efficiencies of propane and butane increased with increasing the electricity production. The heat release rates of propane and butane were similar at a compression ratio of 9:1 because both fuels had similar optimal ignition timings without knocking combustion. Therefore, the difference in electricity efficiencies of engine generators was insignificant. However, at a higher compression ratio of 11:1, the butane engine generator had a lower electricity efficiency than the propane engine generator because its ignition timing retarded to suppress the knocking combustion.

• Journal of ILASS-Korea
• /
• v.27 no.2
• /
• pp.101-108
• /
• 2022

Performance and emissions with different diesel injection methods were analyzed in a natural gas-diesel, dual-fuel engine under low-load conditions. Natural gas was supplied to intake port during the intake stoke to form a natural gas-air premixed mixture for all methods. Diesel was injected directly into the cylinder during the compression stroke in three ways: early injections, late injections, and a combination of early and late injections. The early injections had the highest thermal efficiency among the three methods owing to its highest combustion efficiency. The wide dispersion of diesel before the combustion initiation also allowed superior emissions characteristics.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.16 no.2
• /
• pp.140-153
• /
• 1987

Main objective of this study is to provide heating cost allocation method according to the amount of heating energy consumption in apartments. Heating energy consumptions are calculated by DOE-2.1A program. As a result, heat loss ratio in Ondol heating system, heating cost coefficients of apartments and its using method is presented. Maximum heating cost coefficient rate is 2.63.

• Journal of the KSME
• /
• v.42 no.9
• /
• pp.41-45
• /
• 2002

이 글에서는 전기에너지를 기계적 에너지로 변환시켜 차량에 필요한 동력을 발생시키는 전기동력장치인 모터와 모터제어기에 대하여 그 기술 현황을 소개하고자 한다.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.18 no.1
• /
• pp.29-35
• /
• 1989

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.12 no.3
• /
• pp.179-188
• /
• 1983

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.3
• /
• pp.267-273
• /
• 2013

In order to provide effective operating conditions for the fan in a wet cooling tower with film fill, a new program to search for the minimum fan power was developed using a model of the optimal total annual cost of the tower based on Merkel's model. In addition, a type of design map for a cooling tower was also developed. The inlet water temperature and heat load were considered as key parameters. The present program was first validated using several typical examples. The results showed that for a given heat load, a three-dimensional graph of the fan power (z-axis), mass flux of air (x-axis, minimum fan power), and inlet water temperature (y-axis, maximum of minimum fan power) showed a saddle configuration. The minimum fan power increased as the heat load increased. The conventionally known fact that the most effective cooling tower operation coincides with a high inlet water temperature and low air flow rate can be replaced by the statement that there exists an optimum mass flux of air corresponding to a minimum fan power for a given inlet water temperature, regardless of the heat load.